Additionalfeatures; Lastscenememory; Screensaver; Systemselect - LG DV8631C Owner's Manual

25
Additional Features
Last Scene
Memory
This
player
memorizes last
scene
from the last disc
that is viewed. The last
scene
remains in memory
even
if you
remove
the disc from the
player
or
switch
off the
player.
If you load
a
disc that has the
scene
memorized,
the
scene
is
automatically
recalled.
Note:
This player does not memorize the
scene
of
a
disc if you
switch off the
player
before
commencing to play
the disc.
Screen Saver
The
screen saver
appears when you leave the DVD
player
in
Stop
mode for about five minutes. If the
Screen Saver is displayed for five minutes, the DVD
Player automatically turns
itself off.
System
Select
You must select the appropriate
system
mode for your
TV
system.
If NO DISC appears in the
display
window,
press and hold PAUSE
on
the front
panel
for
more
than 5 seconds
to
be able
to
select
a system
(PAL,
NTSC,
or
AUTO).
Video Mode Setting
?
With certain
discs,
the
playback picture
may be
flickering
or
Dot Crawl is shown
on
straight lines. That
means
Vertical interpolation
or
De-interlace is not
perfectly
matched with the disc. In this
case,
the
picture quality
may be
improved by changing
the
video mode.
?
To
change
the video
mode,
press and hold OSD
about 3 seconds
during
disc
playback.
The
new
video mode number selected is
displayed
on
the TV
screen.
Check whether the video
quality
has
improved.
If
not,
repeat
the above
procedure
until
picture quality is improved.
?
Video mode
change
sequence:
MODE1
→
MODE2
→
MODE3
→
MODE1
?
If you
turn
off the power, the video mode will be
back
to
initial
state (MODE1).
Detailed
Descriptions
for Video Modes
MODE1: The
source
material of the DVD video
(film
material
or
video material) is determined from disc information.
MODE2: Suitable for
playing
film based
content
or
video
based material recorded by the progressive
scan
method.
MODE3: Suitable for
playing
video based content with
comparatively
little motion.
Note:
The video mode
setting only
works when the
Progressive
Scan mode is
set to
"On" in the
Setup
menu.
Controlling
other TVs with the remote control
You
can
control the sound
level, input
source,
and
power switch of your LG TV with the
supplied remote
control.
You
can
control the sound
level, input
source,
and
power switch of non-LG TVs
as
well. If your TV is
listed in the table below, set the appropriate
manufacturer code.
1.
While
holding
down TV POWER
button,
press the
number buttons to select the manufacturer code
for your TV
(see
the table
below).
2. Release TV POWER button.
Code numbers of controllable TVs
If
more
than
one
code number is listed, try entering
them
one
at
a
time until you find the
one
that works
with your TV.
Manufacturer Code Number
LG / GoldStar 1
(Default),
2
Zenith
1,3,4
Samsung 6,7
Sony 8,9
Hitachi 4
Note:
?
Depending
on your
TV,
some or
all buttons may not
function
on
the TV,
even
after
entering
the
correct
manufacturer code.
?
If you enter
a new
code number, the code number
previously
entered will be erased.
?
When you replace the batteries of the
remote,
the code
number you have
set
may be
reset to
the default
setting.
Set the
appropriate
code number
again.