IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
LASER BEAM SAFETY PRECAUTIONS This BD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on.
IMPORTANT SAFETY PRECAUTIONS Product Safety Notice Also check areas surrounding repaired locations. J. Be careful that foreign objects (screws, solder Some electrical and mechanical parts have special droplets, etc.) do not remain inside the set. safety-related characteristics which are often not K.
Page 6
Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards. 1.
STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is When soldering, be sure to use the Pb free solder. indicated as shown. How to Remove / Install Flat Pack-IC Top View Bottom View 1.
Page 8
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
Page 9
2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Page 10
Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Note: (1) Identification (location) No. of parts in the figures This flowchart indicates the disassembly steps to gain (2) Name of the part access to item(s) to be serviced. When reassembling, (3) Figure Number for reference follow the steps in reverse order.
Page 12
[7] DC Fan Motor [6] *Rear Panel Fan Cover (S-5) Fan Plate (S-4) (S-3) (S-6) (S-2) CN1005 (L-1) CN1004 CN5000 (L-1) Fig. D4 (L-2) *See Reference Notes 3. [2] Front Unit Fig. D2 [8] *BD Main CBA (S-7) & BD Mechanism Assembly [4] Front-B CBA (L-4)
Page 13
Power Cover Main PCB Bracket [10] Power (S-10) Supply CBA (S-9) (S-10) [9] AV CBA (S-9) (S-10) Desolder (S-9) Fig. D6 3. How to Eject Manually 1. Remove the Top Cover, Front Unit and BD Main CBA & BD Mechanism Assembly. 2.
HOW TO INITIALIZE THE BLU-RAY DISC PLAYER To put the program back at the factory-default, initialize the BD player as the following procedure. Note: By initializing, network is reset to disconnected state and “Network Service Disclaimer” appears on the screen. 1.
FIRMWARE RENEWAL MODE Note: The file extension of the available firmware is The appearance shown in (*1) of Fig. c is “b35”. described as follows: 1. Turn the power on and remove the disc on the tray Appearance State and close the tray. Now Loading...
Page 16
How to Verify the Firmware Version 1. Turn the power on. 2. Remove the disc on the tray and close the tray. 3. Press [1], [2], [3], [4], and [INFO] buttons on the remote control unit in that order. Fig. h appears on the screen. "...
Page 17
FIRMWARE RENEWAL MODE (for User) 1. Press [ ] button to display Setup menu. 6. Firmware loading starts. Fig. f will appear on the screen and Fig. g appears on the VFD. 2. Select Settings - Advanced Setup - Others - Software Upgrade - Disc Upgrade.
TROUBLESHOOTING FLOW CHART NO.1 The power cannot be turned on. See FLOW CHART No.2 <The fuse blows out.> Is the fuse normal? Is normal state restored when once unplugged Check if there is any leak or short-circuiting on the power cord is plugged again after several seconds? primary circuit component, and service it if defective.
Page 19
FLOW CHART NO.6 P-ON+13V-A(-B) is not outputted. Is 13V voltage supplied to the emitter of Q2603? Check D1023, C1018, C1024, C1026, L1003 and their periphery circuit, and service it if defective. Check Q2601 and PWSW4 line and service it if Is 12V voltage supplied to the base of Q2603? defective.
Page 20
FLOW CHART NO.11 P-ON+1.8V is not outputted. Is 5V voltage supplied to Pin(3) of IC2602? Check D1011, D1013, D1014, C1019, C1025 and their periphery circuit, and service it if defective. Is the "H" signal inputted to Pin(7) of IC2602? Replace IC2000. Replace IC2602.
Page 21
FLOW CHART NO.15 The key operation is not functioning. Are the contact point and the installation state Re-install the switches (SW3007-SW3011) of the key switches (SW3007-SW3011) normal? correctly or replace the poor switch. When pressing each switches (SW3007-SW3011), Check the switches (SW3007-SW3011) and their periphery, and service it if detective.
Page 22
FLOW CHART NO.18 The disc tray cannot be opened and closed. [No Disc] indicated. Both functions of picture and sound do not operate normally. Replace the BD Main CBA & BD Mechanism Assembly. FLOW CHART NO.19 Picture does not appear normally. Set the disc on the disc tray, and playback.
Page 23
FLOW CHART NO.20 Audio is not outputted normally. Set the disc on the disc tray, and playback. Replace the BD Main CBA & BD Mechanism Are the analog audio signals outputted to each pin Assembly. of CN2200? CN2200 16PIN AUDIO(L) CN2200 18PIN AUDIO(R) Are the analog audio signals inputted to each pin Check each line between each pin of CN2200...
INTERNET RADIO (vTuner) ERROR CODE Error Code appears in the error screen when the unit “Summary Error Code” are shown in the list below. detects an error, as shown below. The code is used to Summary specifically determine the cause of error. Error message Error Code Network Error...
Page 25
Detailed Error Code table (vTuner – HTTP Status Code) Status Code Description 201 Created A new resource was created by this unit’s request. 202 Accepted This unit’s request was accepted but its processing is not completed. 204 No Content Though the server processed the request, there was no content. This unit caches latest resource and the requested resource is not modified.
Page 26
Status Code Description An exception error occurred during communication between the server or the 701 Protocol Error broadcast. 702 Start Up Error The application of this unit failed to start. 703 URL Error The URL which this unit specified is in invalid form. Connection with the proxy which exists between this unit and the server or the 705 Connect Failed broadcast has failed.
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 34
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.
Page 35
Power Supply Schematic Diagram CAUTION ! CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. NOTE: For continued protection against fire hazard, If Main Fuse (F1001) is blown , check to see that all components in the power supply replace only with the same type fuse.
Page 36
AV 1 Schematic Diagram 1-11-4 E5SK6SCAV1...
Page 37
AV 2 Schematic Diagram 1 NOTE: Either IC2001 or IC2002 is used for AV CBA. E5SK6SCAV2 1-11-5...
Page 38
AV 3 Schematic Diagram E5SK6SCAV3 1-11-6...
Page 41
BD Main 1 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section. E5SK6SCBD1 1-11-9...
Page 42
BD Main 2 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section. E5SK6SCBD2 1-11-10...
Page 43
BD Main 3 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section. E5SK6SCBD3 1-11-11...
Page 44
BD Main 4 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section. E5SK6SCBD4 1-11-12...
Page 45
BD Main 5 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section. E5SK6SCBD5 1-11-13...
Page 46
BD Main 6 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section. E5SK6SCBD6 1-11-14...
Page 47
BD Main 7 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section. E5SK6SCBD7 1-11-15...
Page 48
BD Main 8 Schematic Diagram E5SK6SCBD8 1-11-16...
Page 49
BD Main 9 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section. E5SK6SCBD9 1-11-17...
Page 50
BD Main 10 Schematic Diagram E5SK6SCBD10 1-11-18...
Page 51
BD Main 11 Schematic Diagram 1 NOTE: The order of pins shown in this diagram is different from that of actual IC6001. IC6001 is divided into nine and shown as IC6001 (1/9) ~ IC6001 (9/9) in this BD Main Schematic Diagram Section. E5SK6SCBD11 1-11-19...
Page 52
Power Supply CBA, AV CBA, Front-A CBA & Front-B CBA Top View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply.
Page 53
Power Supply CBA, AV CBA, Front-A CBA & Front-B CBA Bottom View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. C2303 PIN 7 OF PIN 9 OF PIN 16 OF PIN 24 OF If Main Fuse (F1001) is blown , check to see that all components in the power supply PLUS LEAD CN2200...
SYSTEM CONTROL TIMING CHARTS Power on Hand close [ Tray Close ] [ Tray Open ] SLED moves Start Start Start Start SLED position Hand close Tray close SLED inner initialization detection around moves SLED position Pick-up position Tray open initialization moves [ Tray Open ]...
Page 57
Parameter V*: Voltage T*: Event timer V0: 1.5 V T1: 0.3 s V1: 6.8 V T3: 0.4 s V2: 3.5 V T4: 2.0 s V3: -3.5 V T5: 0.2 s V4: -2.5 V T6: 3.0 s V5: -6.8 V T7: 3.0 s V6: 0.8 V T8: 2.0 s V7: -4.0 V...
IC PIN FUNCTION DESCRIPTIONS IC2000 (SUB MICRO CONTROLLER) Signal Function Name Signal Function Not Used Name FLASH- IN AD-KEY1 Key Date Input Not Used Not Used FLASH- Not Used Not Used Not Used 37 OUT PWSW2 Power On Signal Output 2 Not Used 38 OUT PWSW3 Power On Signal Output 3...
Page 59
IC5001 ( VFD DRIVER ) Signal Function Name Signal Function Name Not Used Not Used Not Used Grid Output Not Used IN OSC Oscillator Input Not Used IN VFD-DIN Serial Data Input Power Supply IN VFD-CLK Serial Clock Input IN VFD-STB Serial Interface Input Ground Not Used...
LEAD IDENTIFICATIONS SL431A-AT 2SA1980M Y 2SA1981Y-AT 2SA1980MG-AT 2SC5344 Y 2SC5343MG-AT STB1277LY-AT E C B R A K E C B 2SA1980SFY BD9321EFJ-E2 2SC5343SFG FA5573N-D1-TE1 PS2561A-1(W) PST8229NR SRA2205SF PST8229UR SRC1203SF 1: Anode 2: Cathode 3: Emitter 4: Collector 1 2 3 M101C77AGE1 BH76071FJ-E2 UTC4580TE...
EXPLODED VIEWS Cabinet 2L082 2L082 2L085 BD Main CBA & BD Mechanism Assembly 2L082 2L062 AC1001 2L072 F1001 FM1001 2L063 2L081 2L070 2L091 2L061 2L083 Power Supply CBA 2L061 2L062 AV CBA 2L061 Front-B CBA Front-A CBA See Electrical Parts List for parts with this mark.
Page 62
Packing Lower Side Upper Side X1-A X2-A S1-A S1-B Some Ref. Numbers are not in sequence. 1-17-2 E5SK6PEX...
ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C1027 CHIP CERAMIC CAP . B K 0.068µF/50V CHD1JK30B683 Before replacing any of these components, read C1033 CHIP CERAMIC CAP .(1608) B K 0.01µF/50V CHD1JK30B103 carefully the product safety notice in this service C1037...
Page 65
Ref. No. Description Part No. Ref. No. Description Part No. CHIP RES. 1/10W F 2k Ω R1020 RRXAFR5H2001 C2608 ELECTROLYTIC CAP . 1000µF/6.3V/M CEA102ENW016 CARBON RES. 1/4W J 1.5k Ω R1021 RCX4JATZ0152 C2609 CHIP CERAMIC CAP .(1608) B K 1µF/10V CHD1AK30B105 CHIP RES.
Page 67
FRONT-A CBA Ref. No. Description Part No. CHIP RES.(1608) 1/10W F 82.0 Ω R2302 RRXAFR5H82R0 Ref. No. Description Part No. CHIP RES.(1608) 1/10W F 82.0 Ω R2303 RRXAFR5H82R0 FRONT-A CBA (AV PCB D) ---------- CHIP RES.(1608) 1/10W F 82.0 Ω R2304 RRXAFR5H82R0 Consists of the following:...
Page 68
Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. BDP5320/F7 E5SK6UD 2010-06-03...