Sealey HS107K Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
read instructions
Wear eye protection Beware hot surfaces Wear protective gloves
1. SAFETY
1.1. ELECTRICAL SAFETY
 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A
residual Current Circuit Breaker (rCCB) should be incorporated in the main distribution board. We also recommend that a residual Current
Device (rCD) is used. It is particularly important to use an rCD with portable products that are plugged into a supply which is not protected
by an rCCB. If in any doubt consult a qualified electrician. You may obtain a residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. the Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a
qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.
and use a Portable Appliance tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and
that the restraint is tight.
Double insulated products, which are always marked with this symbol
(brown) and neutral (blue) wires only.
to rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.
1.1.10. Products which require more than 13amps are supplied without a plug. In this case you must contact a qualified electrician to
ensure that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and
socket with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rCD fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that
the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the
use of 2.5mm² section cable. If an extension reel is to be used outdoors, ensure it is marked for outdoor use.
1.2. GENERAL SAFETY
Disconnect the hot air gun from the mains power before changing accessories, servicing or performing other maintenance.

Maintain the hot air gun in good condition, use an authorised service agent.

Use recommended accessories only. Unapproved accessories can be hazardous and will invalidate your warranty.

Wear appropriate protective clothing and equipment. Work gloves and eye protection are mandatory. Protect long hair and remove

loose fitting garments and jewellery. Maintain correct balance and footing and wear non-slip shoes.
Evaluate your work area before using the hot air gun. i.e. ceiling, floors and enclosures may contain flammable materials.

Keep the work area clean, uncluttered and well lit. Use the hot air gun only in a well ventilated area.

Ensure that small or irregular shaped objects are secured in a vice or clamps before you work on them.

Stay alert! Always pay attention to the work in hand when operating this hot air gun.

Guard against electric shock by not contacting grounded surfaces, i.e. pipes, radiators, etc. when using electric hand tools.

Keep the hot air gun handle dry, clean and free from oil and grease. Clean any paint or varnish from the nozzle after use.

Allow the hot air gun to cool before storing (only store when cold). Store the hot air gun in a safe, dry place out of the reach of

children.
DO NOT direct the hot airflow at yourself, others, animals or plants and DO NOT allow children to operate the hot air gun.

© Jack Sealey limited
InStrUCtIonS For:
VARIABLE TEMPERATURE HOT AIR GUN
KIT 2000W 50-450°C/90-600°C
HS107K
MoDEl no:
, are fitted with live
Original Language Version
RECOMMENDED
FUSE RATING: 13AMP
HS107K Issue: 3(l) - 24/03/15