Sealey SA2004KIT.V2 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear ear
instruction protection
manual
1. saFetY
warNiNG! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
warNiNG! disconnect from the air supply before changing accessories, servicing or performing any maintenance.
‰
maintain the tools in good condition (use an authorised service agent).
9
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
maintain correct balance and footing. Do Not over reach, ensure the floor is not slippery and wear non-slip shoes.
9
warNiNG! Always wear approved eye and hand protection when operating these tools.
‰
use face, dust, or respiratory protection in accordance with cosHH regulations.
9
warNiNG! due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we recommend that
‰
suitable respiratory protection is worn.
depending on the task, the tool noise level may exceed 84dB in which case wear safety ear defenders.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Keep children and unauthorised persons away from the work area.
9
ensure that the workpiece is secure before operating the tool. never hold a workpiece by hand.
9
Do Not operate tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
warNiNG! ensure correct air pressure is maintained and not exceeded. recommended pressure 90psi.
‰
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are secure.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
Do Not use tools for tasks that they are not designed to perform.
8
Do Not operate tools if any parts are damaged or missing as this may cause failure and/or personal injury.
8
Do Not carry the tool by the hose, or yank the hose from the air supply.
8
Do Not place air line attachments close to your face and do not point at other people or animals.
8
Do Not direct air from the air line at yourself or others.
8
Do Not operate tools unless you have been instructed in their use by a qualified person.
8
Do Not carry tools with your finger on the trigger and avoid unintentional starting.
8
Do Not drop, throw or abuse the tools as they are precision instruments.
8
Do Not leave the tools operating unattended.
8
Do Not get the tools wet or operate in damp or wet locations.
8
Do Not allow tools to free run for an extended period of time as this will shorten their life.
8
2. iNtroDuctioN
comprehensive air tool kit containing: medium stroke air hammer, air die grinder, 1/2" drive air impact wrench and 1/2" drive air ratchet wrench.
includes a selection of Walldrive® sockets, extension bar, grinding points, chisels and many accessories. suitable for workshop and bodyshop
applications. supplied in carry case.
3. speciFicatioN
All tools:
max air consumption: ..........................................................5cfm
operating pressure: ...........................................................90psi
Air inlet size: .................................................................. 1/4"BsP
total weight: ..........................................................................8kg
ratchet wrench 1/2" sq. drive:
maximum torque: ................................................45lb.ft, (61nm)
Vibration: ...................................................................... 3.27m/s²
uncertainty: .................................................................... 1.5m/s²
noise power: .................................................................... 102dB
noise pressure: .................................................................. 91dB
© Jack sealey limited
instructions for
air tool kit 4pc with accessories
model no:
Wear eye Wear protective
protection gloves
Original Language Version
sa2004kit.V2
Wear a
mask
impact wrench 1/2" sq.drive:
Working/maximum torque: .......................200/230lb.ft, (312nm)
Vibration: ...................................................................... 5.17m/s²
uncertainty: .................................................................... 1.5m/s²
noise power: .................................................................... 105dB
noise pressure: .................................................................. 94dB
Air die grinder:
chuck size: .......................................................................Ø6mm
free speed: ................................................................ 22000rpm
Vibration: ........................................................................ 1.6m/s²
uncertainty: .................................................................... 0.8m/s²
noise power: .................................................................... 100dB
noise pressure: .................................................................. 89dB
sA2004Kit.V2 | issue 1 17/11/16