Sealey CP20VDD Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
1.1. GENERAL SAFETY
Disconnect the drill from the battery unit before changing accessories, servicing or performing any maintenance.
9
Maintain the drill and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the drill is switched off before installing the battery pack.
9
Keep the drill and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the drill e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
Ensure battery pack is correctly inserted into the drill handle and latched in place before attempting to switch on drill.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep chuck direction switch in the locked position until the drill is required for use.
9
Keep children and unauthorised persons away from the working area.
9
Keep drill and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
9
DO NOT use the drill where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the drill.
8
DO NOT operate the drill if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the drill operating unattended.
8
DO NOT carry the drill with your finger on the power switch. Keep chuck direction switch in the locked position.
8
DO NOT use the drill for a task it is not designed to perform.
8
DO NOT operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the drill or battery charger wet or use in damp or wet locations.
8
2. INTRODUCTION
i
Powerful, lightweight cordless drill/driver with hammer function. Comfortable composite housing with soft grip for added comfort. 2-13mm
keyless chuck. Three drill functions and 18 torque settings provide the control required to complete various tasks. Built in LED work light.
Forward, reverse and trigger lock. Supplied with belt hook for safer storage whilst not in use. Requires battery model no's CP20VBP2,
CP20VBP or CP20VBP4 20V Battery and Model No. CP20VMC Mains Charger.
3. SPECIFICATION
i
Model No: .............................................................CP20VDD
No Load Speed: .................................................... 1250 RPM
Impact Rate: ................................... 0-6000bpm/0-22500bpm
Drilling Capacities:
Chuck Size: ............................................................... Ø13mm
Wood: ....................................................................... Ø35mm
Metal: ........................................................................ Ø13mm
Concrete: .................................................................. Ø13mm
Maximum Torque:..........................................................35Nm
Noise Power..............................................................96.57dB
Noise Pressure .........................................................85.57dB
Vibration ................................................................. 2.546m/s
Uncertainty ................................................................. 1.5m/s
Weight: ........................................................................ 1.25kg
© Jack Sealey Limited
HAMMER DRILL/DRIVER 20V 13MM - BODY
ONLY
MODEL NO:
Wear a Wear ear Wear protective
mask protection
Original Language Version
CP20VDD
gloves
2
2
CP20VDD Issue 2 (3, 4) 08/05/18