Advertisement
Immediately switch off the power tool if the insertion tool gets jammed. The power tool can lash out to the side.
9
Wait until the power tool has come to a standstill, before putting it down.
9
Only use the device for sawing plastic, wood, metal and building materials using the suitable saw blade. The device may be used for:
9
• Sawing work,
• Straight and curved cuts,
• Flush cutting of protruding workpieces
Whilst adhering to the technical data. We recommend using the power tool with original Sealey accessories.
9
The device is not intended for processing glass or stone.
9
Check the device for damages and proper functioning before each use. If you notice damages, no longer use the device.
9
do not use the device when the device or your hands are damp or wet!
8
Work on the electrical components must only be carried out by an authorised specialist company!
9
There is a risk of a short-circuit due to liquids penetrating the housing!
9
do not immerse the device and the accessories in water. Make sure that no water or other liquids can enter the housing.
8
The insertion tool might still be hot after the application. Burn hazard when touching the insertion tool.
9
do not touch the insertion tool bare-handed! Wear protective gloves!
8
warning! Hand injuries Crushing hazard near saw blade and guide shoe if handled without due care. Wear protective gloves!
‰
warning! Sharp object Parts of the saw blade are sharp. Risk of injuries if handled without due care. Wear protective gloves!
‰
warning! Toxic dusts! The harmful/ toxic dusts produced during operation pose of risk to the health of the operator and persons
‰
in the vicinity.
do not process materials containing asbestos. Asbestos is considered carcinogenic.
8
warning! Make sure not to hit power, gas or water lines when working with a power tool. If necessary, use a pipe detector to
‰
check the wall you want to drill in or slit open.
warning! Risk of injuries caused by flying parts or bursting tool heads.
‰
warning! Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way!
‰
warning! The device is not a toy and does not belong in the hands of children.
‰
warning! Risk of suffocation! do not leave the packaging lying around. Children may use it as a dangerous toy.
‰
Vibration emissions can cause a health hazard if the device is used for an extended period of time or if it is not properly handled
9
and maintained.
Keep a sufficient distance from heat sources.
9
note:
If you store or transport the device improperly, the device may be damaged.
note:
For transporting the device, use the transport case included in the scope of delivery in order to protect the device from external
influences. Before transporting the device, observe the following:
Switch off the device.
9
Allow the device to cool down.
9
Remove the tool from the tool holder.
9
2. introduCtion
The CP1200 Series has been designed to make everyday tasks quick and easy. Quality slim, stylish and lightweight tools, powered by one
interchangeable lithium battery. Lithium-ion battery technology delivers better power and performance over traditional nickel-cadmium batteries.
Ergonomic composite housings with soft grip make this a comfortable, easy-to-use kit.
3. speCifiCation
Model no:................................................................. Cp1208
Battery: ................................. 12V 1.5Ah Li-ion (not included)
Consumable Parts: ................................ CP1200BP - Battery
nett Weight: .................................................................. 1.2kg
no load Speed: ................................................... 0-3000spm
noise Power/Pressure: ..........................................95 / 84 dB
Replacement Parts: .................. CP1200MC - Mains Charger
Stroke length:........................................................... 14.5mm
Vibration/Uncertainty: ................................... 13.78 / 1.5 m/s2
Cutting Capacities: ..............................................................
Metal: ............................................................................. 8mm
Wood: .......................................................................... 65mm
Plastic: ......................................................................... 50mm
4. operation
4.1.
general inforMation:
4.1.1.
Keep the venting slots clear to prevent the motor from overheating.
4.1.2.
Before every application, make sure that you have selected the correct tool for the
intended use.
4.2.
CHanging tHe saw Blade
4.2.1.
Turn the quick-release chuck to the side and hold it in this position (fig.1).
4.2.2.
If a saw blade is inserted, remove the saw blade from the quick-release chuck.
4.2.3.
Insert the saw blade into the quick-release chuck. Make sure that the teeth of the
saw blade point downwards.
4.2.4.
Push the saw blade into the quick-release chuck up to the stop.
4.2.5.
Let go of the quick-release chuck. The quick-release chuck must return to its initial
position.
4.2.6.
Check whether the saw blade is properly locked in place.
© Jack Sealey limited
Original Language Version
fig.1
CP1208 Issue 1 25/03/19
Advertisement
