Mitsubishi Electric 800 Series Instruction Manual page 14

Parameter list
Pr. Name
100, 111, 112,
121 to 124, 200,
211, 212, 221 to
Emergency drive mode
523 224, 300, 311,
selection
312, 321 to 324,
400, 411, 412,
421 to 424, 9999
Emergency drive 0 to 590 Hz,
524
running speed 9999
MODBUS RTU
0 to 999.8s,
539 communication check
9999
time interval
USB communication
547 0 to 31
station number
USB communication check
548 0 to 999.8s, 9999
time interval
549 Protocol selection 0, 1
NET mode operation
550 command source 0, 1, 9999
selection
PU mode operation
551 command source 1 to 3, 9999
selection
552 Frequency jump range 0 to 30Hz, 9999
553 PID deviation limit 0 to 100%, 9999 9999
PID signal operation
554 0 to 3, 10 to 13
selection
555 Current average time 0.1 to 1.0s
556 Data output mask time 0 to 20s
Current average value 0 to 500A
557 monitor signal output
0 to 3600A
reference current
Second frequency search 0 to 32767,
560
gain 9999
PTC thermistor protection 0.5 to 30kΩ,
561
level 9999
Energization time
563 (0 to 65535)
carrying-over times
Operating time
564 (0 to 65535)
carrying-over times
Second motor excitation 0 to 400 Hz,
565
current break point 9999
Second motor
566 excitation current low- 0 to 300%, 9999 9999
speed scaling factor
Second motor speed
569 0 to 200%, 9999 9999
control gain
570 Multiple rating setting 0 to 3
571 Holding time at a start 0 to 10s, 9999
4 mA input check 1 to 4, 11 to 14,
573
selection 21 to 24, 9999
Second motor online
574 0 to 2
auto tuning
Output interruption 0 to 3600s,
575
detection time 9999
Output interruption
576 0 to 590Hz
detection level
Output interruption
577 900 to 1100%
cancel level
Traverse function
592 0 to 2
selection
Maximum amplitude
593 0 to 25%
amount
Amplitude
594 compensation amount 0 to 50%
during deceleration
Amplitude
595 compensation amount 0 to 50%
during acceleration
Amplitude acceleration
596 0.1 to 3600s
time
Amplitude deceleration
597 0.1 to 3600s
time
X10 terminal input
599 0,1
selection
First free thermal 0 to 590Hz,
600
reduction frequency 1 9999
First free thermal reduction
601 1 to 100%
ratio 1
First free thermal 0 to 590Hz,
602
reduction frequency 2 9999
First free thermal
603 1 to 100%
reduction ratio 2
First free thermal 0 to 590Hz,
604
reduction frequency 3 9999
Power failure stop
606 external signal input 0, 1
selection
Motor permissible load
607 110 to 250%
level
Second motor 110 to 250%,
608
permissible load level 9999
PID set point/deviation
609 1 to 5
input selection
PID measured value
610 1 to 5
input selection
Acceleration time at a 0 to 3600s,
611
restart 9999
14
INVERTER FUNCTION SETTING
Setting Initial
Pr.
range value
Reverse rotation
617 excitation current low-
speed scaling factor
9999
Cumulative pulse clear
635

signal selection
Cumulative pulse
636

division scaling factor
9999
Control terminal
option—Cumulative
637

pulse division scaling
9999
factor
Cumulative pulse
638

storage
0
Brake opening current
639
selection
9999
Brake operation
640
0
frequency selection
Second brake
9999
641 sequence operation
selection
Second brake opening
642
9999
frequency
Second brake opening
643
9999
current
Second brake opening
644
current detection time
0
Second brake operation
645
1s time at start
0s Second brake operation
646
frequency
Rated

inverter Second brake operation
647

current time at stop
Second deceleration
9999
648 detection function
selection
9999
Second brake opening
650
current selection
0
Second brake operation
651
frequency selection
0
Speed smoothing
653
control
9999
Speed smoothing cutoff
654
frequency
Analog remote output
655
selection
656 Analog remote output 1
657 Analog remote output 2
2
658 Analog remote output 3
9999
659 Analog remote output 4
Increased magnetic
9999
660 excitation deceleration
operation selection
0
Magnetic excitation
661
increase rate
1s
Increased magnetic
662 excitation current level 0 to 300%
0Hz
Control circuit
663 temperature signal
1000%
output level
Regeneration
0
665 avoidance frequency
gain
10%
Power failure stop
668
frequency gain
10% User parameter auto
675 storage function
selection
10% 679 Second droop gain
Second droop filter time
680
constant
5s
Second droop function
681
activation selection
5s
Second droop break
682
point gain
0
Second droop break
683
point torque
9999
Tuning data unit
684
switchover
100%
686 Maintenance timer 2
9999 Maintenance timer 2
687 warning output set time 0 to 9998, 9999 9999
688 Maintenance timer 3
100%
Maintenance timer 3
689
warning output set time
9999
690 Deceleration check time
1
Second free thermal
692
reduction frequency 1
150%
Second free thermal
693
reduction ratio 1
9999
Second free thermal
694
reduction frequency 2
2
Second free thermal
695
reduction ratio 2
3
Second free thermal
696
reduction frequency 3
9999
699 Input terminal filter
Setting Initial
Name
range value
0 to 300%, 9999 9999
0 to 3 0
0 to 16384 1
0 to 16384 1
0 to 3 0
0, 1 0
0, 1 0
0, 7, 8, 9999 0
0 to 30Hz 3Hz
0 to 400% 130%
0 to 2s 0.3s
0 to 5s 0.3s
0 to 30Hz 6Hz
0 to 5s 0.3s
0, 1 0
0, 1 0
0, 1 0
0 to 200% 0
0 to 120Hz 20Hz
0, 1, 10, 11 0
1000%
1000%
800 to 1200%
1000%
1000%
0, 1 0
0 to 40%, 9999 9999
100%
0 to 100°C 0°C
0 to 200% 100%
0 to 200% 100%
1, 9999 9999
0 to 100% 9999
0 to 1s 9999
0 to 2, 10, 11,
9999
20 to 22
0.1 to 100% 9999
0.1 to 100% 9999
0, 1 0
0 (1 to 9998) 0
0 (1 to 9998) 0
0 to 9998, 9999 9999
0 to 3600s,
1s
9999
0 to 590Hz,
9999
9999
1 to 100% 100%
0 to 590Hz,
9999
9999
1 to 100% 100%
0 to 590Hz,
9999
9999
5 to 50ms, 9999 9999
Setting
Pr. Name
range
Maximum motor 0 to 400Hz,
702
frequency 9999
Induced voltage 0 to 5000mV/
706
constant (phi f) (rad/s), 9999
707 Motor inertia (integer) 10 to 999, 9999 9999
711 Motor Ld decay ratio 0 to 100%, 9999 9999
712 Motor Lq decay ratio 0 to 100%, 9999 9999
Starting resistance tuning
717 0 to 200%, 9999 9999
compensation
Starting magnetic pole 0 to 6000μs,
721 position detection pulse 10000 to
width 16000μs, 9999
724 Motor inertia (exponent) 0 to 7, 9999
Motor protection current 100 to 500%,
725
level 9999
Second motor induced 0 to 5000mV/
738
voltage constant (phi f) (rad/s), 9999
Second motor Ld decay
739 0 to 100%, 9999 9999
ratio
Second motor Lq decay
740 0 to 100%, 9999 9999
ratio
Second starting
741 resistance tuning 0 to 200%, 9999 9999
compensation
0 to 6000μs,
Second motor magnetic
742 10000 to
pole detection pulse width
16000μs, 9999
Second motor 0 to 400Hz,
743
maximum frequency 9999
Second motor inertia
744 10 to 999, 9999 9999
(integer)
Second motor inertia
745 0 to 7, 9999
(exponent)
Second motor
746 protection current level 100 to 500%, 9999 9999
0, 10, 11, 20, 21,
50, 51, 60, 61, 70,
71, 80, 81, 90, 91,
Second PID action
753 100, 101, 1000,
selection
1001, 1010, 1011,
2000, 2001, 2010,
2011
Second PID control
0 to 590Hz,
754 automatic switchover
9999
frequency
Second PID action set
755 0 to 100%, 9999 9999
point
Second PID 0.1 to 1000%,
756
proportional band 9999
Second PID integral 0.1 to 3600s,
757
time 9999
Second PID differential 0.01 to 10.00s,
758
time 9999
759 PID unit selection 0 to 43, 9999
Pre-charge fault
760 0, 1
selection
761 Pre-charge ending level 0 to 100%, 9999 9999
762 Pre-charge ending time 0 to 3600s, 9999 9999
Pre-charge upper detection
763 0 to 100%, 9999 9999
level
764 Pre-charge time limit 0 to 3600s, 9999 9999
Second pre-charge fault
765 0, 1
selection
Second pre-charge
766 0 to 100%, 9999 9999
ending level
Second pre-charge
767 0 to 3600s, 9999 9999
ending time
Second pre-charge
768 0 to 100%, 9999 9999
upper detection level
Second pre-charge time
769 0 to 3600s, 9999
limit
Operation panel monitor
1 to 3, 5 to 14,
774
selection 1
17 to 20, 22 to 36,
Operation panel monitor 38 to 46, 50 to 57,
775
selection 2 61, 62, 64, 67, 68,
71 to 75, 87 to 98,
Operation panel monitor
776 100, 9999
selection 3
4 mA input fault
777 0 to 590Hz, 9999
operation frequency
778 4 mA input check filter 0 to 10s
Operation frequency
779 during communication 0 to 590Hz, 9999
error
Acceleration time in
791 0 to 3600s, 9999
low-speed range
Deceleration time in
792 0 to 3600s, 9999
low-speed range
Pulse increment setting 0.1, 1, 10, 100,
799
for output power 1000kWh
0 to 6, 9 to 14,
Control method
800 20, 100 to 106,
selection
109 to 114
801 Output limit level 0 to 400%, 9999 9999
802 Pre-excitation selection 0, 1
Constant output range
803 torque characteristic 0 to 2, 10, 11
selection
Initial
value
9999
9999
9999
9999
9999
9999
9999
9999
9999
0
9999
100%
1s
9999
9999
0
0
9999
9999
9999
9999
9999
0s
9999
9999
9999
1kWh
20
0
0