Advertisement
Quick Links
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications ............................................ 1-1
[2] Operation panel......................................... 1-2
[3] Transmittable documents .......................... 1-3
[4] Installation ................................................. 1-4
[5] Quick reference guide ............................... 1-9
CHAPTER 2. ADJUSTMENTS
[1] Adjustments ............................................... 2-1
[2] Diagnostics and service soft switch .......... 2-2
[3] Troubleshooting...................................... 2-17
[4] Error code table....................................... 2-18
CHAPTER 3. MECHANISM BLOCKS
[1] General description .................................. 3-1
[2] Disassembly and assembly
procedures ....................................... 3-4
CHAPTER 4. DIAGRAMS
[1] Block diagram ............................................4-1
[2] Wiring diagram .......................................... 4-2
[3] Point-to-point diagram ............................... 4-3
Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SERVICE MANUAL
CONTENTS
SHARP CORPORATION
1 - 1
FACSIMILE
UX-2200CM
FO-2150CM
MODEL
CHAPTER 5. CIRCUIT DESCRIPTION
[1] Circuit description ...................................... 5-1
[2] Circuit description of control PWB .............. 5-2
[3] Circuit description of TEL/LIU PWB ......... 5-11
[4] Circuit description of
power supply PWB ............................ 5-14
[5] Circuit description of CIS PWB ............... 5-14
CHAPTER 6. CIRCUIT SCHEMATICS AND
PARTS LAYOUT
[1] Control PWB circuit ................................... 6-1
[2] TEL/LIU PWB circuit ............................... 6-12
[3] Ink sensor PWB circuit ........................... 6-14
[4] Printer PWB circuit ................................... 6-16
[5] Operation panel PWB circuit ................... 6-22
[6] IrDA PWB circuit ...................................... 6-23
[7] Power supply PWB circuit ....................... 6-25
CHAPTER 7. OPERATION FLOWCHART
[1] Protocol ..................................................... 7-1
[2] Power on sequence .................................. 7-2
CHAPTER 8. OTHERS
[1] Service tools .............................................. 8-1
[2] IC signal name .......................................... 8-6
PARTS GUIDE
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UX-2200CMU/CMC
FO-2150CMU/CMC
No. 00ZU220CMUSME
Advertisement
Related Manuals for Sharp FACSIMILE UX-2200CM
Summary of Contents for Sharp FACSIMILE UX-2200CM
- Page 1 " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. This document has been published to be used SHARP CORPORATION for after sales service only. The contents are subject to change without notice.
- Page 2 UX-2200CMU/CMC FO-2150CMU/CMC CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer.
- Page 3 Automatic/Dark selectable As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for procduct improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviation from these values in individual units.
- Page 4 IR IN USE light Press this key to select the reception mode. The selected mode will This blinks while the Sharp Color MFP is receiving data by infrared appear in the display. transmission from a notebook computer, digital camera, or Zaurus.
- Page 5 UX-2200CMU/CMC FO-2150CMU/CMC [3] Transmittable documents 5. Automatic Document Feeder Capacity Number of pages that can be placed into the feeder at anytime is as 1. Document Sizes follows: Normal size: max. ADF 20 sheets (14 lbs – 20 lbs) width 5.83”-8.5”(148 –...
- Page 6 UX-2200CMU/CMC FO-2150CMU/CMC TELEPHONE JACK 7. Use of Document Carrier Sheet A standard RJ11C telephone jack must be located near the machine. A document carrier sheet must be used for the following documents. This is the telephone jack commonly used in most homes and offices. •...
- Page 7 Note:The Sharp MFP is set for touch-tone dialing. If you are on a pulse dial (rotary) line, you must set the Sharp MFP for pulse dialing. Press the following keys on the operation panel: until Press...
- Page 8 The cartridge carrier will move to the center of the print compartment. Note: If the print cartridge moves loosely in the carrier, it is not Open the front cover of the Sharp Color MFP. locked into place. Repeat this step. Close the front cover.
- Page 9 • The cartridge will return to its home position. If you pressed 3 or 4 for a new cartridge, the Sharp MFP will print a test page for printhead alignment. If you installed a new print cartridge, look at the test page and locate the line that comes closest to forming a perfectly straight Pull the paper release plate toward you.
- Page 10 FO-2150CMU/CMC Clearing jammed prining paper The Sharp Color MFP has been set at the factory to scale the size of received faxes to letter size paper. If you have loaded legal paper, you must change the paper size setting to legal. Press these keys: Open the front cover of the Sharp MFP.
- Page 11 3: TRANSPARENCY or the 4 key for a new color cartridge. (Note: Setting 3 only appears if you inserted a The sharp MFP will print a test page for printhead sheet of media in the manual feeder.) alignment. 9. Select the copy print quality. Press 1 for 8.
- Page 12 Selecting the receiving unit to select and enter a symbol. 1. Press: 7. Press: 2. Press 1 for fax reception to the Sharp MFP, or 2 for fax reception to your computer. Note: For your computer to receive faxes automatically, the Color MFP reception mode must be set to AUTO.