ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 1 из 21 ADJUSTMENT Service Mode Entering to Service Mode 1. Set VOLUME to minimum and press button once on remote control. ↓ ↓ ↓ ↓ 2. Press button again and hold button down. ↓...
Page 3
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 2 из 21 Displaying the Adjustment Menu Press MENU button on TV. Service Mode Press ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ Press Adjustment Mode Key Function in the Service Mode The following key entry during display of adjustment menu provides special functions. CAUTION: Never try to perform initialization unless you have changed the memory IC.
Page 4
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 3 из 21 Test signal selection Selection of the adjustment items (on TV or remote control) Change of the data value Volume +/- (on TV or remote control) Adjustment menu mode ON/OFF MENU button (on TV) Initialization of the memory (QA02) CALL + CH button on TV...
Page 5
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 4 из 21 Item Name of adjustment RCUT R CUT OFF GCUT G CUT OFF BCUT B CUT OFF RDRV R DRIVE GDRV G DRIVE BDRV B DRIVE BRTC BRIGHTNESS CENTER COLC COLOR CENTER UVTT BASE BAND TINT CNTX...
Page 6
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 5 из 21 FPLG2 Channel LOGO Vector Clip SW (SD) FPLG3 Channel LOGO Vector Clip SW (HD) Factory preset data will be loaded after setting Model ID data. (Refer to Initialization of Memory Data of QA02 and setting data of signal board.) Adjusting the Data Pressing of VOLUME +/- button will change the value of data in the range from 00H to...
Page 7
OPT5 value C3500 EU Ready 32C3500P/3502P/ 0x07 0x05 3005P/3006P 0x01 0x05 37C3500P/3502P/ 0x07 0x06 3005P/3006P 0x01 0x06 42C3500P/3502P/ 0x01 0x07 3005P/3006P 0x05 0x07 Ex. OPT4 value 0x05 indicates that panel vendor is AUO AMVA. OPT4 (bit7) (bit6) (bit5) (bit4) (bit3) (bit2)
Page 8
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 7 из 21 Ex. OPT5 value 0x05 indicates that panel size is 32. OPT5 (bit7) (bit6) (bit5) (bit4) (bit3) (bit2) (bit1) (bit0) Size Convert from Bit (Binary) to Hex The table for converting from bit (D7-D0) to hex (0x**). BIT (Binary) High nibble Low nibble...
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 8 из 21 E.g. If Bit D7-0 = 0101 1010, Hex data is 0x5A. Exit from Service Mode Pressing POWER button to turn off the TV once. Initialization of Memory Data of QA02 and Setting Data of Signal Unit After replacing QA02 or signal board, the following initialization is required.
Page 10
Perform "Auto tune" on the owner's manual. MODEL ID (HEX) Model name Panel vendor 0x01 32C3500P/3502P/3005P/3006P IPS 0x02 32C3500P/3502P/3005P/3006P LPL 0x03 37C3500P/3502P/3005P/3006P IPS 0x04 37C3500P/3502P/3005P/3006P LPL 0x05 42C3500P/3502P/3005P/3006P LPL 0x06 42C3500P/3502P/3005P/3006P AUO 0x07 0x08 0x09 0x10 0x11 0x12 0x13 0x14 0x15 0x16...
Page 11
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 10 из 21 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x30 0x31 0x32 0x33 Initializing Data setting flowchart after replacing the Signal Unit file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.029\42C... 21.05.2015...
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 11 из 21 Test Signal Selection file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.029\42C... 21.05.2015...
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 12 из 21 Every pressing of button on the remote control changes the built-in test patterns on screen as described below in Service Mode. Picture Signal Red raster Green raster Blue raster All Black All White Self Diagnostic Function 1.
Page 14
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 13 из 21 (1) Firmware : Version information of microprocessor Series name (AAAA) and market area (BB) and software program version (0000) (2) Time : Total hour of turn the TV on. (Unit : H) (3) BL_STATUS : Counter for saving BackLight on error.
Page 15
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 14 из 21 (SCART (S+AV)) (Component/Composite) HDMI1 HDMI2 DTV (Digital Only) Version Check Mode 1. Press "9" button twice on remote control during display of adjustment menu in the service mode. The version of main MPU will be checked. 2.
Page 16
EDID data check item. Display channel numbers depend on HDMI input numbers. OK : EDID data is enable. NG : EDID data is disable. (6) SW Ver Version information of DB software as Toshiba release. (Only digital model.) (7) MW Ver file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.029\42C... 21.05.2015...
Page 17
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 16 из 21 Left side is Application and UI version information of DB software. (Only digital model.) Right side is Firmware (Driver) version information of DB software. (Only digital model.) (8) A/D Adjust A/D adjustment item. --MAIN : It's enable only in double Window model.
Page 18
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 17 из 21 1. Press "9" button thrice on remote control during display of adjustment menu in the service mode. The status of this model will be checked. 2. During Status Check, the following displays are shown. * Status check display and Item are subject to the models.
Page 19
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 18 из 21 (7) SCREEN SIZE : Display the screen size as follows. Exact Scan Wide Super Live 2 Cinema 2 Super Live 1 Cinema 1 Subtitle 14:9 Note: Exact Scan is shown only for 1080p panel model with video input mode except pc. (8) OTHER STATUS : Other status information : Display three numbers of 2 byte data.
Page 20
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 19 из 21 (Video/TV) D3 (bit3) User remote control operation Disable Enable (Service mode and Supere User mode may possible to setting only) D2 (bit2) Disable SET UP MENU except Disable Enable language. (Display the language only) (tuning SETUP MENU) D1 (bit1) Disable SETUP MENU...
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 20 из 21 OPT7 FUNCTION DESCRIPTION 0 (Normal) D7 (bit7) Enable mode that speaker volume will be set Enable Disable in forced when turn ON the main power D6 (bit6) ~ Forced speaker volume 0 ~ 100 [decimal] (Normal: 0) D0 (bit0) Value above 100 is no effect.
Page 22
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 21 из 21 and turn ON the TV. 2 Green is OFF; Abnormal operation of Turn OFF the TV and unplug Red blinks continuously at 1- BUS line. the power cord. second intervals. Plug the power cord in again and turn ON the TV.
Стр. 1 из 1 FUNCTION AND OPERATION The Remote Control Simple at-a-glance reference of your remote control. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.198\42C... 21.05.2015...
Стр. 1 из 2 FUNCTION AND OPERATION Controls and Input Connections A wide variety of external equipment can be connected to the input sockets on the side of the television. Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the television may be used for some functions.
Стр. 2 из 2 Using the Controls and Connections file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.225\42C... 21.05.2015...
Page 26
Стр. 1 из 3 FUNCTION AND OPERATION Tuning the Television Using Quick Setup, Sorting Programme Positions Before switching on the television put your decoder and media recorder to Standby if they are connected. To set up the television use the buttons on the remote control. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.848\42C...
Page 27
Стр. 2 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.848\42C... 21.05.2015...
Page 28
Стр. 3 из 3 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.848\42C... 21.05.2015...
Стр. 1 из 4 FUNCTION AND OPERATION Manual Tune The television can be tuned-in manually using Manual tuning. For example: if the television cannot be connected to a media recorder/decoder with a SCART lead or to tune-in a station on another System. to move across the screen and select any of these Manual Tune options.
Page 30
Стр. 2 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.895\42C... 21.05.2015...
Page 31
Стр. 3 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.895\42C... 21.05.2015...
Page 32
Стр. 4 из 4 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.895\42C... 21.05.2015...
Page 33
Стр. 1 из 2 FUNCTION AND OPERATION Auto Tune Using Auto Tuning file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.641\42C... 21.05.2015...
Page 34
Стр. 2 из 2 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.641\42C... 21.05.2015...
Handling the LCD Module Стр. 1 из 4 SAFETY INSTRUCTION Handling the LCD Module Safety Precaution In the event that the screen is damaged or the liquid crystal (fluid) leaks, do not breathe in or drink this fluid. Also, never touch this fluid. Such actions could cause toxicity or skin irritation. If this fluid should enter the mouth, rinse the mouth thoroughly with water.
Page 36
Handling the LCD Module Стр. 2 из 4 3. If the panel surface becomes soiled, wipe with cotton or a soft cloth. If this does not remove the soiling, breathe on the surface and then wipe again. If the panel surface is extremely solied, use a CRT cleaner as a cleaner. Wipe off the panel surface by drop the cleaner on the cloth.
Page 37
Handling the LCD Module Стр. 3 из 4 6. CMOS-LSI circuitry is used in the LCD module, so avoid damage due to static electricity. When handling the module, use a wrist ground or anchor ground. 7. Do not expose the LCD module to direct sunlight or strong ultraviolet rays for an extended period of time.
Page 38
Handling the LCD Module Стр. 4 из 4 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa1.827\42C... 21.05.2015...
Стр. 1 из 1 PANEL IDENTIFICATION Panel Identification If the several panels are alternatively used in the same model without amending the model name, the identification marking will be shown at the last digit of the set serial number on the specification label on the back cover.
Page 40
U02A LOW-B U01A POWER U03D U03A B-B 11P AV TERM U04A B-B 23P SIGNAL B-B 50P U03B U03C FRONT HDMI...
Стр. 1 из 4 SAFETY INSTRUCTION WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" INSTRUCTIONS BELOW. Safety Precaution WARNING: SERVICING SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE OBSERVED BEFORE SERVICING THIS CHASSIS.
Page 42
Стр. 2 из 4 inflammability, voltage resistance, etc. therefore, use only replacement parts that have these same characteristics. Use only the specified parts when the mark is indicated in the circuit diagram or parts list. 7. Parts mounting and routing dressing of wirings should be the same as that used originally.
Page 43
Стр. 3 из 4 Resistance values in orms ( ). V: Voltmeter or oscilloscope (r.m.s. or peak reading) Input resistance : Input capacitance : 200 pF Frequency range : 15 Hz to 1 MHz and d.c. respectively Note: Appropriate measures should be taken to obtain the correct value in case of non sinusoidal waveforms.
Стр. 4 из 4 Product Safety Notice Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Стр. 1 из 2 SPECIFICATION file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.658\42C... 21.05.2015...
Page 46
Стр. 2 из 2 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.658\42C... 21.05.2015...
Page 59
AV BOARD SIGNAL BOARD PANEL DDR RAM DDR RAM*2 FLI8548 CORTEZ Plus w HDMI ATV(V) VBI Data Processor CVBS PANEL I/F R/G/B/FB EXT1 DCDi (SCART) Video Analog MADi TVOUT V 75ohm Decoder Front Scaling Driver TVOUT L/R CVBS/RGBFB/SY/C/Y/Cb/Cr/RGBHV (16port) LVDS SY/C 75ohm EXT2...
Стр. 1 из 2 SCHEMATIC DIAGRAM Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 61
Стр. 2 из 2 = Electrolytic capacitor = Mylar capacitor 3. The parts indicated with " " have special characteristics, and should be replaced with identical parts only. 4. Voltages read with DIGITAL MULTI-METER from point indicated to chassis ground, using a color bar signal with all controls at normal, line voltage at nominal AC volts.
Page 110
Стр. 1 из 2 CABINET Stand Exploded View A425 A426 A427 A428 A429 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.927\42C... 22.05.2015...
Page 111
Стр. 2 из 2 file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.927\42C... 22.05.2015...
Page 112
Стр. 1 из 35 PARTS LIST All Block Block : Block Location Parts No. Description U01A POW/INV (PE0372) U01A 75010088 PC BOARD ASSY, PE0372B1, POW/INV U01A POW/INV (PE0372) C801 76503510 CAPACITOR, PLASTIC FILM, LE224-C U01A POW/INV (PE0372) C802 76503510 CAPACITOR, PLASTIC FILM, LE224-C U01A POW/INV (PE0372) C803 76092567...
Page 113
Стр. 2 из 35 U01A POW/INV (PE0372) CN113 76092795 CAPACITOR, CERAMIC CHIP, 6.3V B 2.2UF K U01A POW/INV (PE0372) CN114 76092730 CAPACITOR, CERAMIC CHIP, 16V B 0.1UF K U01A POW/INV (PE0372) CN115 76100104 CAPACITOR, CERAMIC CHIP, 25V F 0.1UF Z U01A POW/INV (PE0372) CN116 76092730...
Page 132
Стр. 21 из 35 U04AS SIGNAL (PE0415) C3414 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C3415 75009853 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C3416 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C3417 75009853 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C3418 75009856...
Page 133
Стр. 22 из 35 U04AS SIGNAL (PE0415) C441 75009874 CHIP CERAMIC CAPACITOR (2012) U04AS SIGNAL (PE0415) C442 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C451 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C453 75010146 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C454 75009853...
Page 134
Стр. 23 из 35 U04AS SIGNAL (PE0415) C7908 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C7909 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C7910 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C7911 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C7912 75009856...
Page 135
Стр. 24 из 35 U04AS SIGNAL (PE0415) C7959 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C7960 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C7961 75009868 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C7962 75009868 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C7963 75009868...
Page 136
Стр. 25 из 35 U04AS SIGNAL (PE0415) C915 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C919 75009861 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C9202 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C9204 75009856 CHIP CERAMIC CAPACITOR (1608) U04AS SIGNAL (PE0415) C9205 75009868...
Page 137
Стр. 26 из 35 U04AS SIGNAL (PE0415) E106 23466412 E02S0607ET15 U04AS SIGNAL (PE0415) FL201 75003060 FILTER CHIP BEAD INDUCTOR 47OH U04AS SIGNAL (PE0415) FL202 75003060 FILTER CHIP BEAD INDUCTOR 47OH U04AS SIGNAL (PE0415) FL203 75003060 FILTER CHIP BEAD INDUCTOR 47OH U04AS SIGNAL (PE0415) FL301 75010150...
Page 138
Стр. 27 из 35 U04AS SIGNAL (PE0415) IC331 75008003 IC ANALOG SWITCH U04AS SIGNAL (PE0415) IC360 75009955 AUDIO D/A CONVERTER U04AS SIGNAL (PE0415) IC371 75009908 DUAL AUDIO OP AMP U04AS SIGNAL (PE0415) IC380 75005765 IC EEP ROM U04AS SIGNAL (PE0415) IC381 75005765 IC EEP ROM...
Page 139
Стр. 28 из 35 U04AS SIGNAL (PE0415) PJ404 75009893 1MM PITCH B TO B CONNECTOR U04AS SIGNAL (PE0415) PJ80 75003061 CONNECTOR B-B FLOATING 1.25MM U04AS SIGNAL (PE0415) PJ920 23713949 B-PH-K-S(LF) U04AS SIGNAL (PE0415) Q324 75009815 NPN TRANSISTOR U04AS SIGNAL (PE0415) Q330 75009897 PNP TRANSISTOR...
Page 140
Стр. 29 из 35 U04AS SIGNAL (PE0415) R320 75010116 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R321 75010116 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R3210 75010114 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R3216 75010142 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R3217 75010142 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415)
Page 141
Стр. 30 из 35 U04AS SIGNAL (PE0415) R3812 75010140 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R3813 V01GD0001086 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R382 75007599 CHIP RESISTOR (1005) U04AS SIGNAL (PE0415) R3823 75009850 CHIP RESISTOR (1005) U04AS SIGNAL (PE0415) R3824 75007599 CHIP RESISTOR (1005) U04AS SIGNAL (PE0415)
Page 142
Стр. 31 из 35 U04AS SIGNAL (PE0415) R4261 75010142 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R431 75010114 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R432 75010142 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R433 75009837 CHIP JUMPER 1608TYPE U04AS SIGNAL (PE0415) R434 75010115 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415)
Page 143
Стр. 32 из 35 U04AS SIGNAL (PE0415) R718 75009837 CHIP JUMPER 1608TYPE U04AS SIGNAL (PE0415) R719 75009837 CHIP JUMPER 1608TYPE U04AS SIGNAL (PE0415) R730 75010134 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R732 75010134 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) R734 75010120 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415)
Page 144
Стр. 33 из 35 U04AS SIGNAL (PE0415) RM709 75009839 CHIP NETWORK RESISTOR (1005X4) U04AS SIGNAL (PE0415) RM710 75009839 CHIP NETWORK RESISTOR (1005X4) U04AS SIGNAL (PE0415) RM711 75009839 CHIP NETWORK RESISTOR (1005X4) U04AS SIGNAL (PE0415) RM712 75009839 CHIP NETWORK RESISTOR (1005X4) U04AS SIGNAL (PE0415) RM713 75009839...
Page 145
Стр. 34 из 35 U04AS SIGNAL (PE0415) W9135 75009837 CHIP JUMPER 1608TYPE U04AS SIGNAL (PE0415) W9136 75009837 CHIP JUMPER 1608TYPE U04AS SIGNAL (PE0415) W9143 75009837 CHIP JUMPER 1608TYPE U04AS SIGNAL (PE0415) W9150 75010126 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415) W9151 75010126 CHIP RESISTOR (1608) U04AS SIGNAL (PE0415)
Page 146
Стр. 35 из 35 Packing A702A 75006861 PAD, TOP PACKING Packing A702B 75006860 PAD, BOTTOM PACKING Packing A705 23518043 PACKING, JOINT file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.783\42C... 22.05.2015...
Стр. 1 из 2 PARTS LIST Precaution WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION" FOR DIRECT VIEW CTV ONLY, "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" OF THIS MANUAL. CAUTION: The international hazard symbols " " in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
Page 148
Стр. 2 из 2 : Metal Film : Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted. file://C:\Documents and Settings\Alexsandr\Local Settings\Temp\Rar$EXa0.173\42C... 22.05.2015...