Sealey LED28 Instruction Manual

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you
years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS &
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE
FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
 DO NOT shine directly into your, other person's or animal's eyes.
 DO NOT allow children to use the inspection lamp.
 DO NOT handle or move the inspection lamp whilst it is being charged.
 DO NOT use the inspection lamp if you suspect that the battery or the inspection lamp casing is damaged.
 DO NOT leave battery in a discharged state: recharge battery immediately.If the inspection lamp is not in use,
recharge the battery every 3 to 4 weeks.
1.3. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING INSPECTION LAMP TO THE POWER SUPPLY.
 WARNING! It is the user's responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An rccB
(residual current circuit Breaker) should be incorporated in the main distribution board. We also recommend that an
rcD (residual current Device) is used with all electrical products, particularly portable equipment which is plugged into
an electrical supply not protected by an rccB.
You must also read and understand the instructions concerning electrical safety paragraph 1.3.1 onwards.
1.3.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be
tested by a qualified electrician, using a Portable Appliance tester (PAt), at least once a year.
1.3.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition
of the appliance and the safety of the appliance operator. If in any doubt, contact a qualified electrician.
1.3.3. You must ensure that you:
 Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the
mains power supply. If worn or damaged DO NOT use.
 Important: check that the voltage marked on the charger plug is the same as the power supply to be used.
 uncoil the cable between charger and the inspection lamp.
 DO NOT pull the charger plug from the mains socket by the lead.
 DO NOT use any other type of charger with this inspection lamp.
 DO NOT try to take the charger plug apart.
 DO NOT use the charger plug to charge or power any other electrical item.
 DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).
 WARNING! NEVER substitute a standard 13amp 3 pin plug, or any other type of plug, for the charger plug.
2. INTRODUCTION
• Robust housing with bumper ring.
• 28 LEDs super bright LEDs.
• Incorporates LED charging indicator.
• Integral hanging loop and spring loaded gripper.
• Ideal for use in engine bays and dull work areas.
3. CHARGING
 IMPORTANT WARRANTY INFORMATION:
the battery fitted to this cordless tool is considered to
be a consumable item and its ability to accept charge
will reduce over time. We will warranty it against
mechanical and electrical defect for a period of one
year - this does not cover fair wear and tear. If the
battery is not properly charged before first use, or
regularly conditioned, its capacity will diminish.
under these circumstances we will not replace the
battery even if it is less than one year old.
3.1 Make sure the inspection lamp is switched off before
commencing charging.
3.2 uncoil the charging lead and plug the connector into
the charging socket built into the end of the inspection
lamp handle.
InstructIon MAnuAL for:
CORDLESS INSPECTION LAMP
MoDEL no :
• Battery service life: 3.5 to 7 hours per charge.
• Supplied with mains charger.
• Charging time: 14 hours.
• Charging output: 6V 500 mA DC.
• On/Off switch offers high or low output.
Original Language Version
LED28
LED28 Issue: 3 - 09/01/12