Table of Contents
Advertisement
AM-NX1
Pin No.
Pin Name
98
XMUTE
99
XPATCH
100
SI0
101
SO0
102
SCK0
103
XGUM_ON
104
BEEP
105
XOPT_CTL
106
XHP_STBY
107
AOUT_SEL
108
REC_OPR_LED
109
MDVCC_CTL
110
OPVCC_CTL
111
BATT_CTL
112
VREC_CTL
113
XRST_CHG_IC
114, 115
PD_S0, 1
116
LINK_MON
117
PL_CTL
118
GND_SW
119, 120
NC
121
SLD_MON
122
VLON
123
SLEEP
124
FFCLR
125
CHGI_CTL1
126
CHGI_CTL2
127
ORANGE_LED
128
CHG_LED
129
XTEST
130
XRF_RST
131
XEXT_PWR
132
XHOLD_SW
133
COUT_MON
134
CHG_ADSEL
135
CHGI_SEL
136
XDC_IN
137
SPDL_MON
138
XCS_PWR_IC
139, 140
NC
141
XCS_LCD
142
LCD_STB
XRST_MTR _D
143
RV
54
I/O
O
Analog muting control signal output to the headphone amplifier "L": muting ON
I
Patch function detection terminal "L": patch function (fixed at "L" in this set)
I
Serial data input from the nonvolatile memory
O
Serial data output to the nonvolatile memory and power control
O
Serial clock output to the nonvolatile memory and power control
I
Rechargeable battery detection switch input terminal "L": rechargeable battery in detect
O
Beep sound control signal output to the headphone amplifier
O
Power supply ON/OFF control signal output for the DIN PD drive Not used
O
Power supply control signal output to the headphone amplifier Not used
O
HP/LINE changeover signal output to the headphone amplifier Not used
O
DOWNLOAD LED ON/OFF control signal output terminal
O
Power supply control signal output for the OP modulation Not used
O
Power supply control signal output for the OP laser Not used
O
Control signal output for the voltage step up circuit in the external battery case Not used
O
VREC voltage control signal output Not used
O
Reset signal output to the battery charge control IC
O
PD IC mode changeover signal output to the optical pick up
O
Linking area monitor signal output Not used
O
Plunger control signal output Not used
O
Ground changeover switch control signal output terminal Not used
O
Not used
I
Sled servo monitor signal input
O
Not used
O
System sleep control signal output to the power control "H": sleep
O
Input latch output for the start switching to the power control
O
Charge current limit ON/OFF control signal output at the time of adaptor use "L": limit ON
O
Charge current limit value changeover control signal output at the time of adaptor use Not used
O
Orange LED ON/OFF control signal output Not used
O
LED ON/OFF control signal output for CHG (charge display) "H": LED ON
I
Terminal for the test mode setting (normally open) "L": test mode
O
Reset control signal output to the RF amplifier "L": reset
External power supply (AC adaptor/charging stand) detection signal input
I
"L": external power supply ON
I
HOLD switch input terminal "L": hold ON
I
Traverse count measurement monitor input
O
A/D terminal of the battery charge contro IC output selection signal output
Charge/discharge changeover control signal output for the current sense amplifier
O
"L": discharge, "H": charge
I
DC plug detection signal input terminal "L": DC power supply, "H": battery
I
Spindle servo monitor signal input
O
Chip select signal output to the power control
O
Control signal output for the D class headphone amplifier Not used
O
Chip select signal output to the liquid crystal display module Not used
O
Strobe signal output to the liquid crystal display module
O
Reset control signal output to the motor driver "L": reset
Description
Advertisement
Table of Contents
