Advertisement
DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item replaced by a qualified electrician.
8
1.3.
BATTERY SAFETY PRECAUTIONS
WARNING! Battery contains Lithium-ion which is dangerous. Handle with care to avoid damage, fire, corrosion or personal injury.
‰
Charge battery prior to its first use. The battery will have been shipped in a low charge state. To reduce the risk of burns or fire:
9
DO NOT Attempt to open, disassemble, modify or service the battery pack.
8
DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT Expose to temperatures above 40°C (104°F).
8
Replace only with the battery pack designated for this product.
9
Use only the supplied charging base provided to charge the battery.
9
DO NOT attempt recharging the battery by means of an engine generator or a DC power source.
8
WARNING! Dispose of spent batteries correctly as they contain Lithium-ion. DANGER! DO NOT attempt to disassemble the
‰
battery. For safety and environmental reasons DO NOT discard in domestic waste or by burning. ONLY discard or recycle
according to local authority regulations.
1.4.
GENERAL SAFETY
Disconnect the polisher from the battery unit before changing accessories, servicing or performing any maintenance.
9
Maintain the polisher and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the polisher is switched off before installing the battery pack.
9
Keep the polisher and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the polisher e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
Ensure battery pack is correctly inserted into the polisher handle and latched in place before attempting to switch on polisher.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep children and unauthorised persons away from the working area.
9
Store polisher and charger in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
9
DO NOT use the polisher where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the polisher.
8
DO NOT operate the polisher if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the polisher operating unattended.
8
DO NOT carry the polisher with your finger on the power switch.
8
DO NOT use the polisher for a task it is not designed to perform.
8
DO NOT operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the polisher or battery wet or use in damp or wet locations.
8
2.
INTRODUCTION
Compact, lightweight cordless polisher. Comfortable housing with soft grip to help reduce vibration. Variable speed control trigger makes this
polisher very easy-to-use. Supplied with side handle and polishing pad as well as a 1 hour mains charger and 1 x 2Ah rechargeable Lithium-ion
battery.
3. SPECIFICATION
Model No. ............................................................ CP108VCP
Battery ............................... 10.8V 2Ah Lithium-ion (Included)
Consumable parts .............................CP108VBP 2Ah Battery
Free speed ..........................................0-2400rpm/0-7600rpm
Noise power/pressure .......................................... 91/80dB(A)
Vibration/rating .............................................. 4.7m/s²/1.5m/s²
Pad size .................................................................... Ø75mm
Emissions rating ................................................... 91/80dB(A)
Replacement parts .....................CP108VMC - Mains charger
Thread size ....................................................................... M6
Vibration/uncertainty
Main Handle ................................................. ahAG:4.700m/s²
Auxiliary handle......................... ahAG:3.334m/S2 k=1.5m/s²
4. BATTERY CHARGING
4.1.
Fully charge the battery before first use.
WARNING! Only recharge batteries with the charger supplied.
‰
4.2.
Remove battery by squeezing buttons in on each side. Insert into battery charger.
4.3.
Connect charger to mains supply and red LED will light to signal charging. Once charging is complete LED turns green.
4.4.
Remove from mains supply, remove battery and insert into tool until a click is heard.
4.5.
BATTERY CHARGE STATUS TEST
4.5.1.
Press trigger, all LEDs lit: battery charged, one LED lit: battery needs charging.
4.6.
In order to maintain battery efficiency:
DO NOT fully discharge. After every use fully charge the battery, charge every 4 months even if tool is not used.
8
If a decrease of performance of the tool is noticed, charge the battery.
© Jack Sealey Limited
fig.1
Original Language Version
CP108VCP
Issue 1 13/01/21
Advertisement
