Sealey WCR02 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instructions gloves
1. SAFETY
WARNING! Before use, ensure that there is nothing attached to the motorcycle, that will foul on the clamp.
‰
Maintain the clamp in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Locate the clamp in a suitable area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate lighting.
9
Also ensure that the floor/ground is level and strong enough (preferably concrete) to take the weight of the clamp and the motorcycle.
DO NOT mount the clamp on tarmacadam, as the surface may be unstable.
8
Ensure that the clamps are free from oil and grease before positioning a motorcycle in the clamp.
9
Keep the clamp clean for the best and safest performance.
9
Maintain correct balance and footing whilst positioning the motorcycle in the clamp.
9
Ensure that the floor is not slippery and wear non-slip shoes.
9
Ensure that the motorcycle is adequately secured to the clamp if to be used for transportation purposes.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT use the clamp for a purpose it is not designed to perform.
8
DO NOT operate the clamp if it is damaged.
8
DO NOT use the clamp when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT allow untrained persons to use the clamp.
8
DO NOT make any modifications to the clamp.
8
Before removing a motorcycle from the clamp, ensure that there are no obstructions or persons in the path of the motorcycle.
9
WARNING: The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
‰
may occur.
It must be understood that common sense and caution are factors which cannot be built into this product, but must be
9
applied by the operator.
2. INTRODUCTION
Increases the stability of the motorcycle by clamping the bottom and front of the tyre. Features a pivot clamp which locks the front
wheel securely by the motorcycle weight. Suitable for fitting on trailers, in vans or to motorcycle lifts (Requires suitable fixings). Fully
adjustable to fit wheels Ø15"-21"(380-535mm). Minimum/Maximum tyre width: 50-130mm. Please note: Motorcycle must also be
secured using tie-down straps. Fittings not included.
3. SPECIFICATION
Model No.:.................................................................WCR02
Applications:
MC365, MC365A, MC401, MC401A, MC454, MC455, MCW360, MT400, MT700
4. ASSEMBLY
4.1. Bolt tyre stop in place (fig.1) using supplied fixings.
5. INSTALLATION
5.1. Identify the mounting holes in the base.
5.2. PERMANENT INSTALLATION.
5.2.1. Choose the installation site carefully so that there is good access to both
insert and extract the motorcycle from the clamp..
5.2.2. Ensure that the motorcycle and clamp DO NOT become a hazard.
5.2.3. Use anchor bolt fixings (not supplied) to secure the chock to a solid
concrete surface.
5.3. INSTALLATION FOR TRANSPORTATION.
5.3.1. When used for the transportation of motorcycles, the clamp must be firmly bolted to the floor of the vehicle using suitable fixings.
5.3.2. Check the underside of the floor panel before drilling any holes. Make sure that you DO NOT strike any important vehicle parts.
© Jack Sealey Limited
MOTORCYCLE ROLL-IN WHEEL CLAMP -
BOLT DOWN
MODEL NO:
Wear safety Wear protective
footwear clothing
Original Language Version
WCR02
fig.1
WCR02 Issue 1 07/09/20