Page 1
Konin klijke Philips Electronics N.V. or their respective owners. T P Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
1.Product inforamtion……….……………………………………………………………………………………3 2.Connections overview……..…..…..………………..…………………………………………………………4 3.Mechanical Instructions………………….…………………………………………………………………….5 Cable dres s ing ( 43" 6412 s eries )…………….……………………………………………………………5 Cable dres s ing ( 49" 6412 s eries )…………….……………………………………………………………5 Cable dres s ing ( 65" 6412 s eries )…………….……………………………………………………………6 Cable dres s ing ( 49" 6482 s eries )…………….……………………………………………………………6 Cable dressing (49"/55"/65"...
3.2 As s embly/P an el R emo val 3.2.1 Stand removal 1. Remove the fixation screws [1] that secure the stand 2. Take the stand bracket out from the set. 3.2.2 IR board Control Unit 1. Unplug the connector from the SSB. Caution: be careful, as these are very fragile connectors! 1.
Page 9
3.2.3 Rear Cover Warning: Disconnect the mains power cord before removing the rear cover. 1. Remove fi x ation screws [2] and [3] that secure the base assy.. 2. Gently lift the rear cover from the TV. Make sure that wires and cables are not damaged while lifting the rear cover from the set. ( 64x2 series) (7502 series)
Page 10
3.2.4 Keyboard Control Unit Release the connector from the SSB Board. Caution: be careful, the Keyboard is catch on the Back cover, please be careful to avoid damage the fragile connectors! Remove all the fixation screws from the keyboard control panel [1] and take it out from the Back cover When defective, replace the whole unit.
Page 11
(55" 9002 series) 3.2.5 Small Signal Board (SSB) Caution: it is mandatory to remount all different screws at their original position during re-assembl y . Failure to do so may result in damaging the SSB. 1. Release the clips from the LVDS connector that connect with the SSB[1]. Caution: be careful, as these are very fragile connectors! 2.
Page 12
3. Remove all fixation screws from the PSU. 3. The PSU can be taken out of the set now. 3.2.7 Speakers 1. Gently release the tapes that secure the speaker cables. 2. Unplug the speaker connector from the SSB. 3. Take the speakers out. When defective, replace the both units.
Service Modes Service Modes The Service Mode feature i s split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, whi c h can be used by the Service engineer to repai r /align a TV set. ...
Page 14
With the “LEFT/RIGHT” keys, it is possible to: – (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 15
Public Broadcasting Service password Reset. etc. How to Activate the Factory mode To acti v ate the Factory mode, use the following method: Press the following key sequence on the remote control transmitter: from the “menu/home” press “1999”, directl y followed by the ...
Page 16
Line number for every line (to make CSM language independent). Set the screen mode to full screen (all contents on screen is visible). After leaving the Customer Service Mode, the original settings are restored. Possibility to use “CH+” or “CH-” for channel surfing, or enter the specific channel number on the RC. ...
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading Step 1: Ready for F/W Upgrade 1. Rename the software as “autorun.upg” 2. Prepare a USB memory. 3. Copy the software to USB flash disk(root directory). Note the version of this F/W before you change the software file name. Step 2: F/W Upgrade 1.
Page 18
4. Press OK to start software upgrade 5. Upgrade in progress...
Page 19
Step 3: Check the SW version 1. After burning software, TV will restart 2. Press “Menu+1999+back”, enter Factory mode to check if the software version is correct Caution: Please make sure that software upgrade is finished before unplug the USB and AC power! 5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set.
Page 20
5.2.3 Error codes overview In this chassis only “layer 2” error codes are available and point to problems on the SSB. They are triggered by LED blinking when CSM is activated. Onl y the following layer 2 errors are defined: 5.2.4 How to Clear the Error Buffer The error code buffer is cleared in the following cases: •...
Page 21
“Di s play Code” in below tab. After resetting the Di s play Code, restart the set immediatel y . CTN_ALT Panel Type Display Code Setting Set Option Code BOM# 43PUS6412/05 TPT430U3-EQYSHM.G S1T 49PUS6412/05 TPT490U2-EQYSHM.G SC1T 49PUS6482/05 TPT490U2-EQYSHM.G SC1S 49PUS7502/05 TPT490U2-EQLSJA.G SC4E...
Circuit Descriptions Introduction The TPM17.3E LA is a new chassi s launched in EU in 2017. The w hole range is covered by MT5596UGIJ+ NT72333/NT72334 platform. The major deltas versus its predecessor support DVB-C, DVB-T, DVB-T2, DVB-S, DVB-S2 with also USB3.0,WIFI/multi-media, Video out The TPM17.3E LA LA chassi s comes w ith the follow ing stylings: series xxPUS64x2/xx ...
Page 23
Always replace a defective fuse with one with the correct specifications! This part is available in the regular market. Consult the Philips Service web portal for the order codes of the boards. Important delta’s with the platform are: •...
Page 24
- side-view LED without scanning: PSL power panel - side-view LED with scanning: PSLS power panel - direct-view LED without 2D-dimming: PSL power panel - direct-view LED with 2D-dimming: PSDL power panel. PSL stands for Power Suppl y with integrated LED-drivers. PSLS stands for a Power Suppl y with integrated LED-drivers with added Scanning functionality (added microcontroller).
Page 25
6.3.2 Power layout SSB L4304 +3.5V_SB C4457 +12V AMBI C777 TUNER LNB C4309 +3.3V STANDBY L4101 +2.5V NT C4344 +1.8V EMMC-IO CM47 +1.5V DDR Power SSB Top View...
Page 27
6.4 Front-End Analogue and DV B-T, DV B-C, DV B-S;IS DB-T reception 6.4.1 DVB-C part The Front-End for analogue tuner consist of the following key components: • TUNER EUROPE TDSY-G480D • TUNER EUROPE TDQS-A701F • SCALER MT5596UGIJ HSFBGA-899 Below find a block diagram of the front-end application for DVB-C part. 6.4.2 DTB-T/T2 part The Front-End for DVT part consist of the following key components: •...
Page 28
6.4.3 DTB-S2 part The Front-End for DVT part consist of the following key components: • TUNER EUROPE TDSY-G480D • TUNER EUROPE TDQS-A701F • SCALER MT5596UGIJ HSFBGA-899 • DEMODULATOR Si2169-C60-GMR QFN-48 Below find a block diagram of the front-end application for DTV part. 6.5 HDMI Refer to below for the application.
Page 29
The following HDMI connector can be used: • HDMI 1: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC • HDMI 2: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC • HDMI 3: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC •...
Page 35
8-1-3 Main Power Ha i e r pr oj e c t 需加入12V s wi t c h COLD 12VS L9105 C9110 new part(ER31) 470UF 25V +12V C9130 U9105 SY NC 100N 50V T9101 POWER X'FMR C9105 C9106 C9107 2200uF 25V 470UF 25V 470UF 25V R9124...
Page 36
8-1-4 LED CN8601 +VLED COLD -VLED-1 R8605 HS8604 R8656 D8601/D8602 0 OHM 5% 1/8W C8617 C8620 C8604 R8606 R8607 -VLED-2 1.5NF 82K 2W 82K 2W +VLED D8602 FCF10A40 For LPB function HEAT SINK CONN D8601 FCF10A40 T8601 POWER X'FMR 22:10 FB8601 VLED +24V for PSU function...
Page 59
8-5-11 BE-NT72333f-GND NT72333 GND U3100H Y 10 Y 11 Y 12 Y 13 Y 14 Y 15 Y 16 Y 17 Y 18 Y 19 AA10 AA11 AA12 AA13 AA16 AA20 AA21 AB15 AB20 AB21 AC20 AC21 AC22 AC25 AC26 AD20 AD21 AD22...
Page 92
8-6-21 HDMI-SOC-ARC Clearance = 2 x tracewidth for all SCL and SDA HDMI TMDS signals Differential 100 Ohm nets R7200 100 OHM 1/16W U9400-6 Analog Power HDMI-CEC-IN HDMI-CEC-IN HDMI0-RX0P HDMI_CEC_1 HDMI_0_RX_0 HDMI0-RX0N HDMI_CEC_2 HDMI_0_RX_0B HDMI_0_RX_1 HDMI0-RX1P HDMI0-SCL +1V0-AVDD HDMI0-SCL HDMI_0_SCL HDMI_0_RX_1B HDMI0-RX1N M T 5 5 9 6 P ort0 = H D M I /M H L input...
Page 93
8-6-22 SCART-YPbPr-CVBS AGC-ANA-SOC AGC-ANA-SOC SOC-I2S-SD0 Close to SoC 1. Add ground shielding SOC-I2S-SD0 17 SOC-SPDIF SOC-SPDIF SOC-I2S-SD1 SOC-I2S-SD1 18 for all SCART and YPBPR TER-IFp-SOC TER-IFp-SOC TER-IFn-SOC NC/4.7K 1/16W and DVI signals of Audio TER-IFn-SOC 10000pF 50V C7501 C7500 R7500 NC/470PF 50V &...
8.9 E 715G8555 Keyboard control panel 8-9-1 Key Joystick key define CONN TO SSB JOYSTICK Direction switch Key function Resistance Voltage Range Center 2-5 short Menu 0.0 to 0.22 V CN01 CN04 Right 1-5 short 0.5V 0.39 to 0.60 V KEY 1 AMBI_SPI_CLK Left...