Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Printer
  5. SD-2060
  6. Key operator's manual

Sharp SD-2060 Key Operator's Manual

Electrostatic copying machineelectrostatic copying machine
Hide thumbs Also See for SD-2060:

Advertisement

Quick Links

Download this manual
Downloaded from:
http://www.usersmanualguide.com/
MODEL
SD-2060
ELECTROSTATIC
COPYING MACHINE
KEY OPERATOR'S GUIDE
• KEY OPERATOR CODE
NUMBER (P19)
• KEY OPERATOR
PROGRAMS
• OPTIONAL COUNTER
COMMANDER (SF-EA13)
• KEY OPERATOR
ASSISTANCE CALL
Page
2
3
23
25

Advertisement

loading

Related Manuals for Sharp SD-2060

Summary of Contents for Sharp SD-2060

  • Page 1 MODEL SD-2060 ELECTROSTATIC COPYING MACHINE KEY OPERATOR’S GUIDE Page • KEY OPERATOR CODE NUMBER (P19) • KEY OPERATOR PROGRAMS • OPTIONAL COUNTER COMMANDER (SF-EA13) • KEY OPERATOR ASSISTANCE CALL Downloaded from: http://www.usersmanualguide.com/...
  • Page 2 Downloaded from: http://www.usersmanualguide.com/...

  • Page 3: Table Of Contents

    Key Operator. The programs allow the Key Operator to tailor many functions of the SD-2060 for specific modes of operation. These pro- grams can only be accessed after a Key Operator Code Number has been entered.

  • Page 4: Key Operator Code Number (P19)

    KEY OPERATOR CODE NUMBER (P19) A Key Operator Code Number must be registered before using the key operator programs. The Key Operator must remember this number. Only this registered number will allow access to the key operator programs. Registering the Key Operator Code Number CLEAR/STOP AUDIT CLEAR...

  • Page 5: Key Operator Programs

    KEY OPERATOR PROGRAMS A complete list of all Key Operator Programs is provided below. These programs can only be accessed by first entering the Key Op- erator Code Number. If the optional Card Counter (SF-EA11) is installed, programs 10 to 16 and 18 cannot be accessed.
  • Page 6 KEY OPERATOR PROGRAMS Code No. Program Name Function Page No. Initial Status Sets the copier’s initial settings in the ready condi- Setting tion. Total Copy Count Recalls the total copy counts of the copier, RADF, duplex module, and staple sorter. Right/Left Shift Determines whether shift direction change is to be Direction Selection...

  • Page 7: Using The Key Operator Programs

    KEY OPERATOR PROGRAMS Using the Key Operator Programs Press the CLEAR/STOP key, the INTERRUPT key, and CLEAR/STOP the CLEAR/STOP key again. AUDIT CLEAR The following message will appear. INTERRUPT <P006> ENTER KEY OPERATOR CODE. ––––– Enter the key operator code number. The dashes on the message will change to asterisks.
  • Page 8 KEY OPERATOR PROGRAMS P10 Auditing Mode Program P10 is used to enable or disable the basic auditing mode of operation. When disabled, the message in the display will be “READY TO COPY.” Access to copying is open to any operator. When enabled, the message in the display will be “ENTER YOUR ACCOUNT NUMBER -----.”...
  • Page 9 KEY OPERATOR PROGRAMS To display an individual account Press key 2. The following message will appear. <P014> INPUT ACCOUNT NUMBER TO BE DISPLAYED AND PRESS START. ACCOUNT NUMBER NUMBER OF COPIES MADE ––––– ––––– Enter the account number and press the START key. The number of copies made will be displayed.
  • Page 10 KEY OPERATOR PROGRAMS To display the cost of a particular account Press key 2. The following message will appear. <P017> INPUT ACCOUNT NUMBER TO BE DISPLAYED AND PRESS START. ACCOUNT NUMBER BILLING ––––– ––––– Enter the account number and press the START key. The accumulated cost of copies made will be displayed.
  • Page 11 KEY OPERATOR PROGRAMS P14 Account Number Control Program P14 is used to enter account numbers, clear account num- bers, change an account number, or print all account numbers. For printing the data, an optional counter commander SF-EA13 is needed. (See page 23 for instructions to print.) When P14 is entered, the following message will appear.
  • Page 12 KEY OPERATOR PROGRAMS To change an account number Press key 3. The following message will appear. <P026> INPUT AN ACCOUNT NUMBER TO BE CHANGED. ACCOUNT # –––––, PRESS START. Enter the account number to be changed. Press the START key. The following message will appear.
  • Page 13 KEY OPERATOR PROGRAMS P15 Price/Copy Setting Program P15 is used to set the price per copy. Three price per copy values can be set (#1, #2, and #3). As copies are made, the cumula- tive cost of the copies is kept in memory. When P15 is entered, the following message will appear.
  • Page 14 KEY OPERATOR PROGRAMS P16 Account Limit Setting Program P16 is used to set the maximum number of copies which can be made against an assigned account number. When P16 is entered, the following message will appear. <P030> P16: ACCOUNT LIMIT SETTING. 1.LIMIT.
  • Page 15 KEY OPERATOR PROGRAMS To cancel all limits Press key 2. Press key 1. P17 Machine Identification Number Program P17 is used to enter or print the machine number, which will be printed with the machine auditing data using programs P11, P12, P14, and P29.
  • Page 16 KEY OPERATOR PROGRAMS P19 Key Operator Code Number Change See page 2, KEY OPERATOR CODE NUMBER. P20 Auto Exposure Adjust Use P20 to lighten or darken copies in the automatic exposure mode. The factory setting is “NORMAL.” When P20 is entered, the following message will appear. <G038>...
  • Page 17 KEY OPERATOR PROGRAMS P23 Auto Clear Setting Use P23 to set the time interval to return the copier to the initial set- tings after the last copy of a run has been completed. The time can be set from 10 to 240 seconds in 10 second increments. When P23 is entered, the following message will appear.
  • Page 18 KEY OPERATOR PROGRAMS P25 Limit of Maximum Copies Selected Use P25 to limit the maximum number of copies per copy run which can be input on the COPIES SELECTED display. When P25 is entered, the following message will appear. <P045> P25: LIMIT OF MAXIMUM COPIES SELECTED.
  • Page 19 KEY OPERATOR PROGRAMS P28 Initial Status Setting The copier will assume the initial settings when it is turned on, when the CLEAR ALL key is pressed, or when the auto clear interval has elapsed after a copy run. Use P28 to establish the initial settings. When P28 is entered, the following message will appear.
  • Page 20 KEY OPERATOR PROGRAMS P42 Right/Left Shift Direction Selection This program is used to determine if shift direction change is to be allowed when the CHANGE key is pressed. When P42 is entered, the following message will appear. <P053> P42: RIGHT/LEFT SHIFT DIRECTION SELECTION.
  • Page 21 KEY OPERATOR PROGRAMS P46 Disable Operation Program P46 is used to prevent operation of the copier. It will remain disabled until it is enabled by the key operator. When P46 is entered, the following message will appear. <P079> P46: DISABLE OPERATION. 1.YES 2.NO Select either yes or no using the 10-key pad.
  • Page 22 KEY OPERATOR PROGRAMS P73 Disabling of Job Program Changing Program P73 is used to prevent stored programs from being altered. When P73 is entered, the following message will appear. <P063> P73: DISABLING OF JOB PROGRAM CHANGING. 1.YES 2.NO To prevent job programs stored in memory from being erased or altered, press key 1.
  • Page 23 KEY OPERATOR PROGRAMS P77 Disabling of Covers and Inserts Program P77 is used to prevent the selection of COVERS and IN- SERTS modes. When P77 is entered, the following message will appear. <P067> P77: DISABLING OF COVERS AND INSERTS. 1.YES 2.NO To disable the COVERS and INSERTS modes, press key 1.
  • Page 24 KEY OPERATOR PROGRAMS P92 P Code List Printout Program P92 is used to print out the list of all programs. For printing the data, an optional counter commander SF-EA13 is needed. (See next page for instructions to print.) When P92 is entered, the following message will appear. <P080>...

  • Page 25: Optional Counter Commander (Sf-Ea13)

    Close the printer cover securely. NOTE: Use only specified printer paper. (Sharp Part No. SD-275PR) Do not expose the printer paper to high temperature, exces- sive humidity, or direct sunlight, as doing so could cause dis- colouration of the paper.

  • Page 26: For Printing Data Through Key Operator Programs

    OPTIONAL COUNTER COMMANDER (SF-EA13) For Printing Data through Key Operator Programs For printing data through the key operator programs, Counter Com- mander SF-EA13 must be connected to the copier. If optional Card Counter SF-EA11 is installed, refer to corresponding manual for printing data through SF-EA11. Set the mode switch at the right side of counter commander to [PPC].

  • Page 27: Key Operator Assistance Call

    Contact your authorised Sharp Service Centre for service. AUTOMATIC EXPOSURE IS OUT OF SERVICE. USE MANUAL EXPOSURE. <E018> Service by an authorised Sharp Service Technician is re- READY TO COPY. <E008> quired. Contact your Service Centre as soon as possible.
  • Page 28 SD-2060 SHARP CORPORATION PRINTED IN JAPAN Downloaded from: http://www.usersmanualguide.com/...
  • Page 29 This file has been downloaded from: www.UsersManualGuide.com User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes.. Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide, manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product, documentation manual, user maintenance, brochure, user reference, pdf manual Downloaded from:...