Power consumption Environmental Temperature Humidity (non-condensing) Storage: 10 to 90% RH 2/05 Epson PowerLite 737c Projector Front, rear, upside-down (ceiling mount) 1 W monaural 4:3 (horizontal:vertical) 1:1.2 36 dB (Low Brightness mode) Supports USB (type B) UHE (Ultra High Efficiency)
Follow these steps to plug in and turn on the projector: 1. Remove the lens cap. Caution Do not use the projector with the lens cap in place. The heat generated by the lamp can damage the cap. 2. Connect one end of the power cord to the projector’s power inlet.
Source button on Search If you’re using a Macintosh You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select click 2. Select Arrangement If you’re using a Macintosh with OS 8.6 to 9.x:...
If the image is too low, you can raise it by extending the projector’s front adjustable foot. 1. Stand behind the projector. Press up on the blue foot release lever and lift the front of the projector to extend the front adjustable foot.
Adjusting the Image Shape The projector automatically corrects images that are distorted when the projector is tilted up or down (up to a 15° tilt). The Keystone window appears on the screen while the projector makes the correction. If the projected image still isn’t rectangular or has a “keystone”...
Menu Note: When Direct Power On is enabled, shut down the projector as you normally would. Follow the instructions in the next section. (The projector will start automatically when power is restored after a power failure if it is plugged in.) Shutting Down the Projector When you’ve finished using the projector, follow the...
❏ Do not expose batteries to heat or flame. ❏ Dispose of used batteries according to local regulations. ❏ Remove the batteries if you won’t be using the projector for a long time. Follow these steps to replace the AAA alkaline batteries: 1.
If you enter the incorrect password 30 times in a row, the projector is locked and remains locked until an authorized Epson servicer can unlock it. You can also create a user’s logo for the projector, to be displayed as the startup screen and/or AV/Mute screen.
EasyMP as EasyMP the source. 2. Locate the Epson 802.11 b/g card that came with your projector. Insert it with the label facing upward. Note: Only the Epson 802.11 b/g card is guaranteed to work.
Page 11
(802.11g or 802.11b) access point or an AirPort (or AirPort Extreme) base station, and one or more computers with wireless network cards or adapters. 1. Switch the projector to EasyMP mode and insert the Epson 802.11 b/g card. 2. When you see the EasyMP screen, press the...
Page 12
Epson PowerLite 737c Projector 6. Select the appropriate settings for your mode: ESSID Ad hoc: Enter an ESSID in the ESSID textbox. Access point: Enter an ESSID, which is the SSID name of your access point or the name of your AirPort network.
Page 13
If you don’t see this tab, you may need to enable your wireless card or network device by clicking device settings; then follow any instructions on the screen to enable the device. 2/05 Epson PowerLite 737c Projector Obtain IP address . Otherwise, select Use the following IP and enter the required information.
Page 14
10.Click the AirPort icon on the menu bar at the top of the Macintosh desktop. You see the AirPort status menu: 11.Check to make sure AirPort is turned on. 12.Select your projector’s ESSID (ad hoc) or the name of your AirPort network (access point). System 2/05 icon.
Page 15
Note: You must have installed EMP NS Connection from your projector CD-ROM. See the User’s Guide for installation instructions. 1. Make sure you’ve inserted the Epson 802.11 b/g card in the projector’s card slot (see page 10). 2. Windows: Select EMP NS Connection Start menu.
Page 16
Epson PowerLite 737c Projector 4. Once the name of your projector appears, select it and click . If more than one projector is listed, you can select Connect up to four additional projectors and connect to them at the same time. If the selected projector is being used by another person, you can still connect to it;...
Page 17
Indicates search in progress If the search fails to find a projector with the specified IP address, the searching icon turns into a question mark. If this happens, run EasyMP to check the projector’s IP address, then repeat this step.
To start EMP Monitor, click Start > Programs Programs > EPSON Projector > EMP Monitor If you’ve added the program to the Startup programs folder, it may already be open. If so, click the icon in the system tray on...
Page 19
(or port) they are projecting an image, and if a problem occurs. Status icon Video Source icon Note: To monitor a projector when it’s in standby mode (plugged in but not projecting), you must first select setting in the projector’s Extended menu. Standby Mode...
If you need the most current status information about your projectors, click the button. Refresh Note: To turn on a projector when it’s in standby mode (plugged in but not projecting), first select Network ON setting in the projector’s Extended menu. Configuring the Monitoring Interval...
Power If dirt is difficult to remove or the filter is torn, replace it. Contact your dealer or call Epson at (800) 873-7766 to obtain a new set (part number V13H134A08). In Canada, please call (800) 463-7766 to locate a dealer.
Turn the projector off when not in use. Continuous use may reduce the overall life of the product. Contact your dealer or call Epson at (800) 873-7766 in the United States for a replacement lamp. Request part number . In Canada, please call (800) 463-7766 to locate a V13H010L32 dealer.
False ceiling plate Security bracket/cabling for gyro lock mounts Adjustable ceiling channel You can purchase these accessories from an Epson authorized reseller. For product information and to find the nearest authorized reseller, please call 800-GO-EPSON (800-463- 7766) or browse our catalog of products at www.epson.com, select the product you are interested in, and click "Where to...