SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON product. EPSON is not responsible for any use of this information as applied to other products.
Your projector includes these outstanding features: ■ Connectivity Your EPSON PowerLite projector can be connected to four computer and five video sources (up to a total of six sources at the same time). You can include an independent sound channel for each of the six sources.
Built-in help system Provides assistance for common problems. Available from the button on the projector or the remote control. Help support.epson.com Download FAQs and e-mail your questions to EPSON support. ® Support card. Keep the...
Start Here kit for details. To register, simply fill out the registration card included in your Start Here kit and mail it to EPSON. Or you can register online at www.epson.com/webreg. Registering also lets you receive special updates on new accessories, products, and service.
* Remove the plastic film from the projector’s control panel. Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location.
These cables may be included with your video player; check the appropriate section in Chapter 1 to make sure of the kind of cable you need. You may be able to purchase it from EPSON (see page 14) or from your video dealer.
Optional Accessories To enhance your use of the projector, EPSON provides the following optional accessories: Product Replacement lamp and air filter Air filter set Mounting hardware: Projection screens: Lenses: Cables: Macintosh adapter set (monitor and desktop adapter) Remote control cable set...
Setting Up the Projector his chapter gives you basic information on setting up the projector: where to position it and how to connect it to a video source (such as a VCR or DVD player) or to a notebook or desktop computer.
Place the projector on a sturdy, level surface. Make sure there is plenty of space for ventilation around and under the projector. Do not set the projector on top of loose papers that could block the vents under the projector.
Page 17
(see page 43). Screen Side View If you place the projector below screen level, you’ll have to tilt it up by extending its feet. This causes the image to lose its square shape, but you can correct the distortion by pressing the described on page 44.
To find the distance when you know the screen’s diagonal size: ■ ■ To find a screen’s diagonal size when you know the distance: ■ ■ Setting Up the Projector Distance at Wide setting (inches) = × (diagonal screen size [inches] Distance at Tele setting (inches) = ×...
Connecting to Video Equipment You can connect up to five video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video-output connections: ■ RCA connector (composite video) ■ S-video connector ■...
2. Connect the cable to the yellow video output connector on your player and the yellow Video 3. If you want to play sound through the projector, see page 33 for instructions on connecting an audio cable. 4. If you don’t need to make any other connections, see Chapter 2 for instructions on turning on the projector and adjusting the image.
3. If you want to play sound through the projector, see page 33 for 4. If you don’t need to make any other connections, see Chapter 2 Setting Up the Projector equipment, or you can purchase it from EPSON; see page 14). connector on the projector: S-Video instructions on connecting an audio cable.
3. If you want to play sound through the projector, see page 33 for instructions on connecting an audio cable. 4. If you don’t need to make any other connections, see Chapter 2 for instructions on turning on the projector and adjusting the image.
2. Connect the cable to the video port on your player and the 3. If you want to play sound through the projector, see page 33 for 4. If you don’t need to make any other connections, see Chapter 2 Setting Up the Projector If your player has a single VGA connector, see below.
Page 25
2. Connect the cable to your player and the corresponding connectors on the projector. 3. If you want to play sound through the projector, see page 33 for instructions on connecting an audio cable. 4. If you don’t need to make any other connections, see Chapter 2 for instructions on turning on the projector and adjusting the image.
Connecting to a Computer You can connect the PowerLite projector to any computer that has a note standard VGA, BNC, or DVI-D (or DFP) dual-link monitor port, The projector accepts a wide including desktop models and PC notebook computers, Macintosh range of resolutions and PowerBooks and iBooks, and hand-held devices.
Connecting to the Computer 1 or 2 Port Follow these instructions to connect to one or both of the projector’s Computer ports: 1. Locate the computer VGA computer cable that came with the projector. If your computer provides video output through BNC connectors, you can use a BNC/VGA cable instead (commercially available).
(to the H/C Sync or V Sync ports). port. play sound through the projector (see page 33), or connect a USB cable to use the remote control as a mouse (see page 31). for instructions on turning on the projector and adjusting the image.
3. Connect the other end to your computer’s DVI port. 4. Optionally, you can connect an external monitor (see page 32), play sound through the projector (see page 33), or connect a USB cable to use the remote control as a mouse (see page 31).
If so, you’ll need to use a Macintosh desktop adapter to connect the VGA cable to your computer (available from EPSON; see page 14). 1. To use the adapter, remove its cover as 2.
Connecting the Cable for Remote Mouse Control If you’ve connected a computer as described in this chapter, you can use the projector’s remote control as a wireless mouse. This lets you control your computer and click through slideshow-style presentations, such as PowerPoint away.
Connecting an External Monitor If you want to monitor your presentation close-up (on a monitor note placed beside the projector) as well as on the screen, you can connect The monitor can display images from any connected an external monitor. You can use it to check on your presentation or computer or video source.
Playing Sound Through the Projector You can play sound through the projector’s speaker system, or you can attach an external speaker system. (Attaching speakers to the projector instead of directly to the audio source lets you use the projector’s remote control to adjust the sound.)
2. Connect the stereo mini-jack end of your audio cable to the 3. Connect the other end of the cable to your speaker system. You The projector’s internal speaker system is disabled while sound is output to the external speakers.
If you turn on your connected computer or video equipment before starting the projector, the projector automatically detects and displays the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source manually (see page 38).
Page 37
New Hardware Wizard saying your computer has found a plug-and-play monitor; if so, click If you want to allow the projector to turn on directly when you plug it in (or when you turn on the power when the projector is plugged in to a wall switch-controlled outlet) you can enable the direct power on option.
Selecting the image source lets you switch between images input from To focus and adjust the different pieces of equipment connected to the projector (such as a image, see page 42. If a computer or DVD player). projected image fails to appear, see page 39 for help.
(Allow a few seconds for the projector to sync up after pressing the button.) If you’re using a Windows/PC notebook, press the function key ■...
Page 40
If you’re using Macintosh OS X: You may need to set up your system to display the same image on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select 2. Make sure the 3.
Page 41
If you’re using OS 8.6 to 9.x: You may need to set up your system to display the same image on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select Monitors Monitors and Sound.
If the image still isn’t large enough, you may need to move the projector farther away from the screen. You can also use the buttons on the remote control to zoom in on a portion of the image.
If the image is too low on the screen, you can raise it using the Lens Shift buttons. This is the best method for adjusting the height of the image. If you need to raise the image further, you can tilt the projector upward by extending the feet.
Adjusting the Image Shape In most cases, you can maintain a square or rectangular image by placing the projector directly in front of the center of the screen and using the Lens Shift (instead of tilting the projector upward) to adjust the image height.
Page 45
Enter 6. Use the pointer button on the remote control (or the arrow buttons on the projector) to adjust the shape. 7. Repeat steps 5 and 6 as needed to adjust any remaining corners. 8. When done, press to exit the menu system.
If you’ve connected a computer and the image doesn’t look right, or it doesn’t fit properly on the screen, press the remote control (or the control panel). This automatically resets the projector’s tracking, sync, resolution, and position settings. note You must be projecting an image for this button to have any effect.
After the projector has cooled, the orange light stays on and the exhaust fan shuts off. If you want to turn the projector on again, wait until the orange light stops flashing. Then press the 4.
Giving Your Presentation presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 30 feet away. You can use the remote control to adjust the picture and sound...
Point the remote control either at the front or back of the projector, or at the screen. Stand within about 30 feet of the projector. If you want to operate the projector from a greater distance, a remote control cable set is available (see page 14).
Using the Navigation Buttons The remote control has various buttons that let you navigate the projector’s help and menu systems; they also let you use the drawing tools to highlight your presentation. With an optional USB cable connecting the projector to your computer, the buttons can be used in place of your computer’s mouse, letting you walk about freely while...
Or you can control all of the projectors simultaneously by setting the remote control’s ID to zero. Setting the Projector ID The projector’s default ID is 1. If you need to change it, follow these steps: 1. Press the 2.
2. Press one of the numbered buttons on the remote control to select the desired ID (0 through 9). Select zero to control all projectors, or select a number to match the ID of the projector(s) you want to operate.
Replacing the Batteries If the projector stops responding to the remote control, check the following: ■ ■ caution If the buttons do not light up, replace the batteries as described below: When replacing batteries, 1. Turn the remote control over.
Switching Between Picture Sources If your projector is connected to more than one computer and/or video source, you can switch between the different sources: On the projector’s control panel, there are two ■...
Previewing Picture Sources You can use the Preview function to help you select the image source. 1. Press note Movies are displayed as still images on the preview screen. Currently selected source note A red highlight surrounds the preview window for the currently selected source.
A/V Mute the image and sound and darken your screen. (If you’ve connected an external monitor to the projector, it will continue displaying.) This feature is useful if you want to temporarily redirect your audience’s attention without the distraction of a bright screen.
Displaying a Picture-in-Picture Video If you’re displaying an image from equipment connected to the DVI, note Computer 1, Computer 2, or BNC port, you can open up a smaller Depending on your picture-in-picture (P-in-P) window on the screen. This window can equipment’s ports, you may be able to connect either a display video from either the Video or S-Video port.
Controlling the Volume To change the volume, press the up) side of the button. Volume Volume If necessary, you can adjust the tone using the projector’s menu system. See page 73. (volume down) or (volume note To temporarily shut off the sound (and picture), press button.
Highlighting Your Presentation You can display a pointer to call out something on the screen, or draw straight or curved lines to emphasize particular points. There are three preset pointer tools you can choose from, and each one can be customized for a different look.
Customizing the Pointer Tools You can customize the shape and size of each of the three pointer tools, select the color and width of the line made with each pointer, and set how fast you can move the pointer across the screen. 1.
Enter To use the remote control this way, you have to connect a USB cable (not included) between your computer and the projector (see page 31). While projecting a presentation, this setup also lets you use the buttons to move through your slideshow.
You can transfer any image from your computer or video source to the projector, and then use it as your startup screen. You can also use it as the screen to be displayed when the projector is not receiving a signal...
Enter Saving the logo may take a few moments. Do not use your projector or video source (computer, DVD player, etc.) while the logo is being saved. the menu screen. button to display the menu screen (if not already Menu displayed).
Fine-tuning the Projector ou can use the projector’s on-screen menus to adjust the image, sound, and other features. This chapter covers the following information: Using the menu system ■ Adjusting the image quality ■ Adjusting the image size, shape, and position ■...
Using the Menu System You can use the remote control (or the projector’s control panel) to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button note You can also use the buttons...
Reset All Reset All Preset Reset Reset ]: Select ]: Enter To restore all the projector settings to their factory-default values, select Reset All pointer button to adjust pointer button to highlight the Enter button to save your button to exit.
Enter ■ Sharpness Adjusts the sharpness of the image. Adjust 0000 Auto Manual Adjust Select [Presentation [Presentation Select Auto Manual Execute [Menu]: Exit to let the projector Auto and then Manual...
Auto (or the button on the projector). Auto/Enter This automatically resets the projector’s tracking, sync, resolution, and position settings. If further adjustment is needed, you can change these settings manually as described below. ■...
Page 70
Resolution (in the Video menu) If your image is distorted (compressed, stretched, partially cut off, or doesn’t completely fill the display area), the projector’s resolution setting may not match that of your computer. Select to let the projector adjust the resolution automatically; or...
■ Keystone (in the Setting menu) Squares up the shape of the image after the projector has been tilted upward or angled to one side (see page 44). If you notice lines or edges looking jagged after adjusting the shape, decrease the Sharpness setting (see page 68).
Adjusting the Color The projector provides several ways for you to adjust the color: ■ Color Mode button ■ ■ ■ ■ ■ Fine-tuning the Projector Color Mode button (also in the Video menu) Lets you quickly adjust the color and brightness for various environments.
]: Enter 2. Use the pointer button to highlight the desired option, then adjust it as needed: ■ Volume ■ Treble ■ Bass Execute [Menu]: Exit note You can also adjust the volume using the remote control. Fine-tuning the Projector...
Using Direct Power On You can set up the projector to turn on immediately once it is plugged in (or receives power from a wall switch). 1. Press the 2. Use the Make sure you do not unplug the projector to turn it off. You must power off the projector as described on page 47 to allow it to cool down, or you will damage the projector.
Image Setup Options Use these settings to change how the projector processes incoming video signals. Several of these settings should normally be left at the factory default setting (except for the Computer1, Computer2, and BNC Input settings).
■ ■ Communication Setup Options These options let you set up the projector so it can be monitored and controlled from a remote computer (see Chapter 5). ■ note When this setting is on, you cannot view or change the projector’s network settings.
■ Sleep mode (in the Setting menu) When sleep mode is on, the projector turns off the lamp if it has not received any input signals for 30 minutes. Turn sleep mode off if you want the lamp to remain on all the time (this is the default setting).
You can also purchase an optional Kensington MicroSaver anti-theft device to connect to the lock port on the projector’s left side. See page 14 for ordering information. Setting Up Password Protection 1.
Page 79
If the length of time is set to “0,” the password entry screen only appears when the power is turned on the first time after the projector has been plugged in. note Make a note of your password and keep it in a safe place.
Using the Projector When Password Protection Is On note When the projector is first plugged in and the power is turned on, the If an incorrect password is password entry screen appears. entered three times in succession, the message “The projector’s operation will be...
(see page 85). To use the EasyManagement software, first install it as described on page 82. Then connect and configure each projector you want to monitor, so it can be recognized on your network (see page 84). This chapter covers the following: ■...
Installing the EasyManagement Software The projector software CD-ROM includes the software you need to use the projector’s EMP Monitor and EMP Network Manager. System Requirements Before you install the software, make sure your computer meets these note requirements: The software cannot be ■...
Page 83
Manager instructions on the screen to finish installing it. 4. If you want to be able to manage the projector remotely from this computer, select the option for same way. 5. When done installing the software, click the Once installed, you can access these programs from your computer’s...
Projector Before using the EMP software to manage your projector(s), you have to connect each projector you want to monitor to your network and configure it with an appropriate IP address. 1. Connect the projector to your network using a commercially...
Page 85
Num button ■ To change the network addresses from the projector’s control panel, press the right and left arrow buttons to select the part of the address you want to enter, then use the up and down arrow buttons to increase or decrease the numeric value.
To close EMP Monitor, right-click the program icon shown above, then select Exit Registering a Projector Before you can monitor a projector, you have to register it. Follow these steps: 1. Open EMP Monitor as described above. You see this screen: Click here...
Page 87
If the name of a projector and enter the projector’s does not appear, you can give it a name or change its existing one in EMP NetworkManager (see page 95). Click here Close Managing the Projector from a Remote Computer...
Network ON setting in Standby Mode the projector’s menu system (see page 76). For detailed status information, select the projector in question and click Managing the Projector from a Remote Computer Status icon Video Source icon View details...
Page 89
You may also see this error if Standby Mode is turned off (see page 76). The following table explains the meaning of the video source icons: Video source icons Computer 1 Computer 2 S-Video Video Managing the Projector from a Remote Computer...
To turn on a projector when button to see a description of its meaning.) Make sure you’ve selected it’s in standby mode the projector(s) you want to operate (with the mouse pointer) before (plugged in but not projecting and not in full clicking one of the buttons.
If you need to have the most current status information about your projectors, click the button in the EMP Monitor screen. Refresh You can also select how often EMP Monitor checks the projector status: 1. From the Tool menu, select You see this screen.
Using EMP NetworkManager You can use EMP NetworkManager to send out messages by e-mail, notifying you when a problem occurs with a projector. Before running EMP NetworkManager, make sure you’ve installed the software as described on page 82. Then follow the steps below to create e-mail settings for each projector you want to monitor.
2. If you’d like to register a projector manually and you know its IP address, click the Projector address selection You see this screen: 3. Enter the projector’s IP address and click icon is added to the EMP NetworkManager screen.
Creating the E-Mail Settings 1. If 2. Double-click the icon for the projector whose e-mail settings you 3. EMP NetworkManager connects to the projector, and you see note The projector must be plugged in (projecting or in standby mode) for you to be able to connect to it.
Page 95
11. When you see the test message window, you can send a message with the heading “TEST MAIL” to the addresses you have entered. The projector’s name and IP address are included in the body of the message. 12. When done making all your projector settings, close the EMP NetworkManager.
Understanding the Notification Messages If a projector experiences a problem, it sends an e-mail message to each of the addresses you provided using EMP NetworkManager. The message includes the heading “EPSON Projector” in the subject line. The body of the message contains: ■...
XGA (1024 × 768) or better display adapter and monitor ■ Installing the Software 1. Turn on the computer’s power, start Windows, and then place the EPSON Projector Software for Multi Screen CD-ROM into the computer’s CD-ROM drive. The installer will start automatically. 2. Click...
Guide. Follow these steps to view the guide: ® Acrobat Reader to view the guide. 1. Insert the EPSON Projector Software for Multi Screen CD-ROM 2. Double-click the 3. Right-click on the 4. Double-click the 5. Double-click the The guide opens in Adobe Acrobat.
Any dirt or smears on the lens may show up on your projected image. warning You also need to periodically clean the air filters on the projector. A Before you clean any part of clogged air filter can block ventilation needed to cool the projector.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. ■ ■ Cleaning the Projector Case Before you clean the case, first turn off the projector and unplug the power cord. ■ ■ ■ Maintaining the Projector Remove the cap before cleaning Use a canister of compressed air to remove dust.
To clean the air filters, follow these steps: 1. Turn off the projector and unplug the power cord. 2. To clean the filters, EPSON recommends using a small vacuum cleaner designed for computers and other office equipment. If you don’t have one, gently clean the filters with a soft brush (such as an artist’s paintbrush).
Replacing the Filters 1. Turn the projector over (unless it’s ceiling-mounted). 2. Remove the filters from the projector by sliding them out to the 3. Remove each filter from its holder by releasing the two tabs, as 4. Install new filters in the holders, aligning the tabs with the slots on 5.
■ The lamp warning light ■ Contact your dealer or call EPSON at (800) 873-7766 in the United States for a replacement lamp. Request part number In Canada, please call (800) 463-7766 for dealer referral. Follow these steps to replace the lamp: 1.
Page 104
Install them as described on page 102. 10. Reset the lamp timer as described in the next section. Maintaining the Projector the way). Then remove the cover. remove them). cover. (The projector won’t come on if the lamp cover is loose.)
1. Press the button on the remote control (or on the Menu projector’s control panel). You see the main menu. 2. Use the pointer button on the remote control (or the arrow buttons on the projector) to highlight...
When hand-carrying the projector, you should use the handle to lift it only a short distance (for example, to set it on a table). To move the projector over longer distances, place it on a rolling cart or use a dolly.
Solving Problems you how to contact technical support for problems you can’t solve yourself. If the projector is not working correctly, first look at its status lights note and check for possible solutions on page 108. If you’re having a You can also get on-screen problem with the image or sound, see page 112;...
The lights on top of the projector indicate the projector’s status and let you know when a problem occurs. If the projector seems to be indicating a problem, locate the pattern of lights in the table on the next page, then follow the recommended solutions.
Page 109
Description and solution If no lights are on, make sure the power cord is connected securely both at the power outlet and the projector. If you have just replaced the lamp, make sure the cover is securely fastened When the power light is orange, the projector is in sleep mode. Press the Power Orange button to turn it on.
Page 110
Then plug the power cord back in and press the Power button. If the projector continues to overheat, contact EPSON for help (see page 118). Warning: Except as specifically explained in this User’s Guide, do not attempt to service this product yourself.
Use the About menu to view information on the display settings of your computer and the number of hours the lamp has been used. To access the About menu: 1. Press the button. You see the projector’s main menu Menu screen. 2. Highlight the...
If you enter the wrong password nine times, the projector will not turn back on again and you will need to contact EPSON. If you forget your password or the projector becomes locked, contact EPSON as described on page 118.
Page 113
■ and the cover securely reattached, or the projector won’t come on. ■ If you just turned off the projector, it may still be cooling down. Wait until the power light stops flashing and remains orange; then press the P button to turn the projector back on.
Page 114
■ The image isn’t square, but tapered on the sides. ■ ■ If you can’t place the projector this way, correct the shape using the QuickCorner feature in the projector’s menu system (see page 45). Solving Problems Press the button on the remote control to make sure the Resize projector is displaying at the correct resolution or aspect ratio.
Page 115
Focus Make sure the lens is not fogged up by condensation. You may ■ need to wait before using the projector after moving it from a cold environment to a warm environment. If you’re projecting from a computer, press the ■...
Page 116
Press the button on the remote control; you can use Color Mode the preset options to adjust the projector’s brightness and color for various lighting environments. You can further adjust the color using various settings in the projector’s menu system (see page 72).
Make sure the remote control ID matches the ID of the projector ■ you want to operate (see page 52). If you don’t know the projector ID, set the remote control ID to zero; this lets it work with any projector. If you’ve held down the ■...
Telephone Support Services To use the EPSON PrivateLine Support service, call (800) 637-7661 and enter the PIN on the EPSON PrivateLine Support card included in your Start Here kit. This is the fastest way of speaking to a live representative, and it’s free. This service is available 6 Pacific Time, Monday through Friday, for the duration of your warranty period.
Installation permanent location, such as a theater or conference room. Placement and Mounting Guidelines The projector can be installed for four different viewing setups: front projection, ceiling mounting, rear projection onto a semi-transparent screen, or rear/ceiling projection, as shown: Front projection Rear projection To project from overhead, you’ll need the optional ceiling mounting...
If you’ve installed the wide-angle rear projection If you mount the projector on the ceiling above screen level, you’ll lens, you won’t be able to use have to tilt it down to center the image on the screen. This causes the the projector’s Focus, Zoom,...
Installing Multiple Projectors If multiple projectors are installed in one room, you can assign to each projector a separate ID number. This lets the presenter use the remote control to operate each projector independently (see page 52). If you have multiple projectors installed at your place of business and want to be able to monitor and control them over a network, see “Managing the Projector from a Remote Computer”...
Appendix B: Technical Specifications General Type of display Size of LCD panels Lens Resolution (native format) Color reproduction Brightness (typical) Contrast ratio Image size Projection distance Projection methods Internal sound system Optical aspect ratio Zoom ratio Noise level Keystone correction Poly-silicon TFT active matrix Diagonal: 1.4 inches (35.6 mm) F=1.7 to 2.2, f=53 to 72 mm...
Projection Lamp Type Power consumption Lamp life Part number Remote Control Range Battery Mouse Compatibility Dimensions Height Width Depth Weight Electrical Rated frequency Power supply Power consumption Appendix B: Technical Specifications UHE (Ultra High Efficiency) 200 W Up to 7000 hours V13H010L26 Approx.
Environmental Temperature Operating: 41 to 104°F (5 to 40°C) Storage: 14 to 140 °F ( Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Operating altitude 0 to 7500 ft (0 to 2286 m) Safety United States FCC 47CFR Part 15B Class B (DoC) UL1950 Rev.
SDTV (480p) TV (525i) TV (625i) Compatible Computer Display Formats You can connect the projector to a wide range of computers, including PCs and notebooks, Apple Macintosh, Power Macintosh (including G3 and G4 systems), PowerBook computers, many iMac and iBook Although images are displayed at the projector’s native resolution of...
Page 127
You may need to modify existing presentation files if you created them for a different resolution. See your software documentation for details. The projector supports these monitor display formats: Mode Refresh Rate (Hz) VGAEGA VGA—60...
■ Do not use the projector near water or sources of heat. ■ Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company. ■ Place the projector near a wall outlet where the plug can be easily unplugged.
Page 130
If liquid has been spilled into the projector, or if it has been exposed to rain or water. If it does not operate normally when you follow the operating instructions, or if it exhibits a distinct change in performance, indicating a need for service.
Remote Control Information You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. The projector may not respond to remote control commands under the following conditions: ■ There is an object between the remote control IR emitter and the IR receiver on the projector.
Trade Name: Type of Product: Projector Model: Marketing Name: PowerLite 9300i Appendix C: Notices EPSON AMERICA, INC. 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806-2469...
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
(e.g., fuses), other than lamps. This warranty is not transferable. EPSON is not responsible for warranty service should the EPSON label or logo or the rating label or serial number be removed or should the product fail to be properly maintained or fail to function properly...
Page 135
To locate the Authorized EPSON Servicer nearest you, call the EPSON Connection at (800) 637-7661 + PIN or (562) 276-4394 in the U.S. and (905) 709-3839 in Canada or write to: Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012. Appendix C: Notices...
Default settings, restoring, 67 Desktop adapter, Macintosh, 30 Different image on notebook and screen, 39 to 41 Distance from projector to screen, 16, 123 Drawing on the screen, 60 to 61 DVI cable, 14, 29 EasyManagement installing software, 82 to 83...
Page 138
HP OpenView, 81 iMac, connecting to, 13 Image adjusting, 42 to 46, 68 to 72 capturing and saving in projector, 63 to 64 correcting shape, 44 to 45, 71, 114 fitting on screen, 46, 71, 114 focusing, 42 height, adjusting, 43 to 44...
Page 139
Network settings, 76, 84 to 85 New Hardware Wizard, 37 No-Signal Msg setting, 64, 77 Notebook computer, displaying on, 39 to 41 Options for projector, 13 to 14 Picture source, selecting, 38, 55 to 56 Picture, see Image Picture-in-Picture function, 58...
Page 140
46, 71, 114 different images on notebook and screen, 39 image and sound problems, 39 to 41, 112 to 116 projector problems, 107 to 116 remote control problems, 117 tapered image, 44 to 45 Turning off picture (using A/V Mute), 57...
EasyMP.net option access panel Status lights Handle Speaker Foot release button Control Panel Activates menu system Turns projector on and off Switches between equipment connected to ports Press and hold to use arrow buttons to adjust Tracking and Sync Squares up...
Source Preview Preset Auto Focus Zoom LensShift Volume Power Turns the projector on and off On/Off switch Turns the remote control on and off Pointer Moves cursor on the screen Effect Selects pointer or drawing tool Help Provides on-screen help...