1. Manuals
  2. Brands
  3. Epson Manuals
  4. Projector
  5. PowerLite D6150
  6. User manual

Epson PowerLite D6150 User Manual

Epson powerlite d6150: user guide
Hide thumbs Also See for PowerLite D6150:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Maintenance Manual, Operating Manual
®
PowerLite
D6150/D6155W/D6250
User's Guide

Advertisement

Table of Contents
loading

Related Manuals for Epson PowerLite D6150

Summary of Contents for Epson PowerLite D6150

  • Page 1 ® PowerLite D6150/D6155W/D6250 User's Guide...

  • Page 3: Table Of Contents

    Projector Parts Locations ... 14 Projector Parts - Front/Top ... 15 Projector Parts - Rear ... 16 Projector Parts - Base... 17 Projector Parts - Control Panel ... 18 Projector Parts - Remote Control... 19 Setting Up the Projector ... 21 Projector Placement... 21 Projector Setup and Installation Options ...
  • Page 4 Connecting to External Speakers ... 36 Connecting to External USB Devices ... 37 USB Device Projection... 37 Connecting a USB Device or Camera to the Projector... 38 Selecting the Connected USB Source ... 38 Disconnecting a USB Device or Camera From the Projector... 39 Connecting to a Document Camera ...
  • Page 5 Turning Off the Projector ... 67 Selecting the Language for the Projector Menus... 68 Adjusting the Image Height ... 69 Image Shape... 70 Correcting Image Shape With Quick Corner... 70 Correcting Image Shape With the Keystone Buttons... 72 Resizing the Image With the Zoom Ring ... 74 Focusing the Image Using the Focus Ring...
  • Page 6 Password Security Types ... 95 Setting a Password ... 95 Selecting Password Security Types... 96 Entering a Password to Use the Projector ... 97 Saving a User's Logo Image to Display... 99 Locking the Projector's Buttons ... 101 Unlocking the Projector's Buttons ... 101 Installing a Security Cable ...
  • Page 7 Solutions When No Image Appears on an External Monitor... 151 Solutions When There is No Sound or Low Volume ... 152 Solving Projector or Remote Control Operation Problems ... 152 Solutions to Projector Power or Shut-Off Problems... 152 Solutions to Problems With the Remote Control... 153 Solutions to Password Problems ...
  • Page 8 Supported Video Display Formats... 162 Notices ... 164 Important Safety Information ... 164 Important Safety Instructions... 164 FCC Compliance Statement... 167 Trademarks ... 168 Software Copyright... 169 Copyright Notice... 196 Copyright Attribution ... 196...

  • Page 9: Introduction To Your Projector

    The PowerLite D6150, D6155W, and D6250 projectors include these special features: Bright, high-resolution projection system • PowerLite D6150/D6155W: Up to 3500 lumens of brightness (white light output and color light output) PowerLite D6250: Up to 4000 lumens of brightness (white light output and color light output) •...

  • Page 10: Product Box Contents

    Introduction to Your Projector Related concepts Projector Parts Locations Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping. Make sure your projector box included all of these parts:...
  • Page 11 Projector Remote control Remote control batteries (two AA alkaline) Power cord VGA computer cable Cable clips Cable cover Password Protected sticker Projector documentation CD Projector software CD...

  • Page 12: Additional Components

    Parent topic: Projector Features Optional Equipment and Replacement Parts You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online www.epsonstore.com Epson offers the following optional accessories and replacement parts for your projector:...

  • Page 13: Warranty And Registration Information

    In addition, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada. See the Extra Care Road Service brochure for details.

  • Page 14: Notations Used In The Documentation

    Projection Operation Guide installed with this manual from your projector CD. • If you still need help after checking this manual and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. For details, see "Where to Get Help".

  • Page 15: Projector Parts - Front/Top

    Parent topic: Introduction to Your Projector Projector Parts - Front/Top Exhaust vent (with shutter) Projector status lights Remote receiver Zoom/focus ring cover Foot release lever Front adjustable foot Lens cover glass Speaker Air intake vent (air filter) Optional wireless LAN module indicator light...

  • Page 16: Projector Parts - Rear

    Focus ring Cable cover Control panel Lamp cover Parent topic: Projector Parts Locations Projector Parts - Rear Optional wireless LAN module port and stopper Cable cover screw holes RS-232C port Monitor Out port Audio Out port A/C input port Cable clip holes...

  • Page 17: Projector Parts - Base

    USB TypeA port USB TypeB port Computer2 port Audio2 port Computer1 port Audio1 port L-Audio-R audio ports S-Video port Video port HDMI port Trigger out port Parent topic: Projector Parts Locations Projector Parts - Base Mounting bracket holes Alternate mounting bracket holes...

  • Page 18: Projector Parts - Control Panel

    Source Search button (searches for connected sources) Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons Horizontal keystone adjustment buttons (adjust screen shape) and arrow buttons Help button (accesses projector help information) Esc button (cancels/exits functions) Enter button (selects options)

  • Page 19: Projector Parts - Remote Control

    Projector Parts - Remote Control Power button Computer button (cycles through connected computer sources) Video button (cycles through connected video sources)
  • Page 20 Help button (accesses projector help information) Color Mode button (selects display modes) Num button (switches buttons to number function for entering numbers) ID button (selects projector and remote control ID numbers) User button (customizable for different functions) USB button (cycles through connected USB sources)

  • Page 21: Setting Up The Projector

    • Place the projector on a sturdy, level surface or install it using a compatible mount. • Leave plenty of space around and under the projector for ventilation, and do not place it on top of or next to anything that could block the vents.
  • Page 22 Rear Ceiling...

  • Page 23: Projection Distance

    Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
  • Page 24 Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image. (Conversion figures may have been rounded up or down.) PowerLite D6150/D6250 4:3 Aspect Ratio Image or Screen...
  • Page 25 Screen or image size Projection distance (1) Wide to Tele 200 inches (508 cm) 223 to 363 inches (567 to 922 cm) 250 inches (635 cm) 280 to 454 inches (710 to 1154 cm) 300 inches (762 cm) 336 to 545 inches (853 to 1385 cm) 16:9 Aspect Ratio Image or Screen Screen or image size...
  • Page 26 Screen or image size Projection distance (1) Wide to Tele 150 inches (381 cm) 182 to 296 inches (463 to 753 cm) 200 inches (508 cm) 243 to 396 inches (618 to 1005 cm) 250 inches (635 cm) 305 to 495 inches (774 to 1257 cm) 275 inches (699 cm) 335 to 545 inches...
  • Page 27 Screen or image size Projection distance (1) Wide to Tele 150 inches (381 cm) 177 to 288 inches (450 to 732 cm) 200 inches (508 cm) 237 to 385 inches (602 to 978 cm) 250 inches (635 cm) 296 to 482 inches (753 to 1223 cm) 280 inches (711 cm) 332 to 539 inches...
  • Page 28 Screen or image size Projection distance (1) Wide to Tele 100 inches (254 cm) 133 to 217 inches (339 to 552 cm) 120 inches (305 cm) 160 to 261 inches (407 to 663 cm) 150 inches (381 cm) 201 to 327 inches (510 to 830 cm) 200 inches (508 cm) 268 to 436 inches...

  • Page 29: Projector Connections

    • For presentations or slide shows without a computer, you can connect USB devices (such as a flash drive or camera) or an optional document camera. Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode to ensure the projector's internal temperature is regulated properly.

  • Page 30: Connecting To Computer Sources

    Note: To connect a Macintosh that includes only a Mini DisplayPort or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's VGA video port. Contact Apple for compatible adapter options.

  • Page 31: Connecting To A Computer For Hdmi Video And Audio

    Connecting to a Computer for USB Mouse Control If you connected your computer to a Computer or HDMI port on the projector, you can set up the remote control to act as a wireless mouse. This lets you control computer presentations at a distance from your computer.

  • Page 32: Connecting To A Computer For Sound

    Connecting to a Computer for Sound If your computer presentation includes sound and you did not connect it using the projector's HDMI port, you can still play sound through the projector's speaker system. Just connect an optional 3.5 mm stereo mini-jack audio cable as described here.

  • Page 33: Connecting To An Hdmi Video Source

    Connecting to an HDMI Video Source If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable. 1. Make sure the projector and your video source are turned off. 2. Connect the HDMI cable to your video source's HDMI output port.

  • Page 34: Connecting To A Composite Video Source

    Input Signal Settings - Signal Menu Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable. 1. Make sure the projector and your video source are turned off.

  • Page 35: Connecting To A Video Source For Sound

    • Connect the other end of the cable to the projector's Audio port that corresponds to the Computer port you are using for video. • Connect the red and white plugs on the other end of the cable to the projector's L-Audio-R ports. Audio1 or Audio2 port...

  • Page 36: Connecting To An External Computer Monitor

    Connecting to an External Computer Monitor If you connected the projector to a computer using a Computer port, you can also connect an external monitor to the projector. This lets you see your presentation on the external monitor even when the projected image is not visible.

  • Page 37: Connecting To External Usb Devices

    3. Connect one end of the cable to your external speakers as necessary. 4. Connect the stereo mini-jack end of the cable to your projector's Audio Out port. Audio Out port Parent topic: Projector Connections Connecting to External USB Devices Follow the instructions in these sections to connect external USB devices to the projector.

  • Page 38: Connecting A Usb Device Or Camera To The Projector

    Projecting a Slide Show Connecting a USB Device or Camera to the Projector You can connect your USB device or camera to the projector's USB Type A port and use it to project a slide show or presentation. 1. If your USB device came with a power adapter, plug the device into an electrical outlet.

  • Page 39: Disconnecting A Usb Device Or Camera From The Projector

    Connecting to External USB Devices Connecting to a Document Camera You can connect a compatible Epson document camera to your projector's USB Type A port to project images viewed by the camera. Note: You may be able to connect different Epson document camera models to your projector's Computer ports.

  • Page 40: Attaching And Removing The Cable Clips

    Attaching and Removing the Cable Clips You can install the cable clips that came with your projector to provide additional support to the power and HDMI cables. 1. Plug in the power and HDMI cables. 2. Insert each guide into the cable clip holes near the power inlet and HDMI port.
  • Page 41 2. Place the cable cover on the projector as shown, guiding the cables through the notch on the base of the cable cover. 3. Tighten both cable cover screws. To remove the cover, loosen both screws and take the cover off of the projector.

  • Page 42: Installing Batteries In The Remote Control

    Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. 1. Open the battery cover as shown. 2. Insert the batteries with the + and – ends facing as shown.
  • Page 43 3. Close the battery cover and press it down until it clicks into place. Parent topic: Setting Up the Projector...

  • Page 44: Using The Projector On A Network

    EasyMP Network Projection Operation Guide installed from your projector CD for instructions. • EasyMP Monitor software (Windows only) lets you monitor and control your projector through the network. You can download the latest software and documentation from the Epson web site. Go to www.epson.com/support...

  • Page 45: Selecting Wired Network Settings

    Before you can project from multiple computers on your network, you must select the network settings for the projector using its menu system. Note: Make sure you already connected the projector to your wired network using the LAN port. 1. Turn on the projector.
  • Page 46 5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control.

  • Page 47: Wireless Network Projection

    Wired Network Projection Wireless Network Projection You can send images to your projector through a wireless network. To do this, you must install the optional Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless projection.

  • Page 48: Installing The Wireless Lan Module

    • Configuring the connection manually using the projector's Network menus After installing the module and setting up the projector, install the network software from the Epson Projector Software CD on your computer. Use the following software and documentation to set up, control, and monitor wireless projection: •...
  • Page 49 2. Remove the screw securing the wireless LAN module stopper, then remove the stopper. 3. Insert the wireless LAN module into the port.

  • Page 50: Using Quick Wireless Connection (Windows Only)

    Optional Equipment and Replacement Parts Using Quick Wireless Connection (Windows Only) You can use the optional Epson Quick Wireless Connection USB key to quickly connect the projector to a Windows computer wirelessly. Then you can project your presentation and remove the key when you are done.

  • Page 51: Selecting Wireless Network Settings Manually

    After a few minutes, your computer image is displayed by the projector. If it does not appear, press the LAN button on your projector remote control or restart your computer. 5. Run your presentation as necessary. 6. When you finish projecting wirelessly, remove the USB key from your computer.
  • Page 52 5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control.

  • Page 53: Wireless Lan Menu Settings

    9. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. After you complete the wireless settings for your projector, you need to select the wireless network on your computer.
  • Page 54 Description Selects the type of wireless connection: Quick: lets you quickly connect to one computer or use the optional Epson Quick Wireless Connection USB key to connect Advanced: lets you connect to multiple computers via a wireless network access point...

  • Page 55: Selecting Wireless Network Settings In Windows

    Wireless Network Projection Setting Up Wireless Network Security You can set up security for your projector to use on the wireless network. Set up one of the following security options to match the settings used on your network: • WEP encryption •...

  • Page 56: Wireless Security Menu Settings

    Wireless Security Menu Settings Parent topic: Wireless Network Projection Wireless Security Menu Settings Settings on the Security menu let you select the type of security and security settings that match the network you are connecting the projector to. Setting Security Options Description...

  • Page 57: Setting Up Projector Network E-Mail Alerts

    Setting Up Wireless Network Security Setting Up Projector Network E-Mail Alerts You can set up the projector to send you an e-mail alert over the network if there is a problem with the projector. 1. Press the Menu button on the remote control.
  • Page 58 Note: Your e-mail address can be up to 32 alphanumeric characters long. 9. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.

  • Page 59: Network Projector E-Mail Alert Messages

    • The IP address of the affected projector • Detailed information about the problem Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert. Parent topic: Setting Up Projector Network E-Mail Alerts...

  • Page 60: Controlling A Networked Projector Using A Web Browser

    Using the Projector on a Network Controlling a Networked Projector Using a Web Browser Once you have connected your projector to your network, you can select projector settings and control projection using a compatible web browser. This lets you access the projector remotely.
  • Page 61 Note: If you set Standby Mode to Communication On, you can use a Web browser to select settings and control projection even if the projector is in standby mode. You cannot select all of the projector menu settings or control all projector functions using a web browser.

  • Page 62: Crestron Roomview Support

    Crestron RoomView lets you control and monitor your projector using a web browser. Note: You cannot use the Epson Web Control feature or the Message Broadcasting plug-in for EasyMP Monitor when you use Crestron RoomView.

  • Page 63: Controlling A Networked Projector Using Crestron Roomview

    Crestron RoomView Support Controlling a Networked Projector Using Crestron RoomView Once you have set up your projector to use Crestron RoomView, you can control and monitor projection using a compatible web browser. 1. Start your web browser on a computer connected to the network.
  • Page 64 • Menu displays the Configuration menu 5. To view information about the projector, click the Info tab. 6. To change projector, Crestron, and password settings, click the Tools tab, select settings on the displayed screen, and click Send. 7. When you finish selecting settings, click Exit to exit the program.

  • Page 65: Using Basic Projector Features

    Color Mode Controlling the Volume With the Volume Buttons Projecting a Slide Show Turning On the Projector Turn on the computer or video equipment you want to use before you turn on the projector so it can display the image source.
  • Page 66 The projector beeps and the power light flashes green as the projector warms up. After about 30 seconds, the power light stops flashing and turns green. Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is especially dangerous for children and pets.

  • Page 67: Turning Off The Projector

    2. Press the power button again. (To leave it on, press any other button.) The projector beeps twice, the lamp turns off, and the power light turns orange. Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the projector for transport right away.

  • Page 68: Selecting The Language For The Projector Menus

    3. To transport or store the projector, make sure the power light is orange (but not flashing), then unplug the power cord. Caution: To avoid damaging the projector or lamp, never unplug the power cord when the power light is green or flashing orange.

  • Page 69: Adjusting The Image Height

    3. Press the down arrow button to select the Extended menu and press Enter. Note: The Network menu does not appear on non-network projector models. 4. Press the down arrow button to select the Language setting and press Enter. 5. Select the language you want to use and press Enter.

  • Page 70: Image Shape

    You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.
  • Page 71 1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. 2. Press the Menu button. 3. Select the Settings menu and press Enter. 4. Select the Keystone setting and press Enter.

  • Page 72: Correcting Image Shape With The Keystone Buttons

    6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter. 7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc.
  • Page 73 2. Press a keystone button on the projector's control panel. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape using the Keystone settings in the projector menus.

  • Page 74: Resizing The Image With The Zoom Ring

    1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. 2. To enlarge or reduce the image size, rotate the projector's zoom ring. Parent topic:...

  • Page 75: Remote Control Operation

    Remote Control Operation The remote control lets you control the projector from almost anywhere in the room, up to 19.7 feet (6 m) away. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the angles listed here.

  • Page 76: Using The Remote Control As A Wireless Mouse

    Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries. Using the Remote Control as a Wireless Mouse...

  • Page 77: Using The Remote Control As A Presentation Pointer

    Using the Remote Control as a Presentation Pointer You can use the projector's remote control as a pointer to help you call out important information during a presentation. The default pointer shape is an arrow, but you can select an alternative shape using the Settings menu.

  • Page 78: Selecting An Image Source

    Projector Feature Settings - Settings Menu Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other. 1. Make sure the connected image source you want to use is turned on.

  • Page 79: Projection Modes

    Using Basic Projector Features Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen.

  • Page 80: Changing The Projection Mode Using The Remote Control

    Changing the Projection Mode Using the Remote Control You can change the projection mode to flip the image over top-to-bottom. 1. Turn on the projector and display an image. 2. Hold down the A/V Mute button on the remote control for five seconds.

  • Page 81: Image Aspect Ratio

    Projection Modes Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios. Normally the input signal from your video source determines the image's aspect ratio. However, for certain images you can change the aspect ratio to fit your screen by pressing a button on the remote control.

  • Page 82: Changing The Image Aspect Ratio

    Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Aspect button on the remote control.

  • Page 83: Color Mode

    Image Aspect Ratio Color Mode The projector offers different Color Modes to provide optimum brightness, contrast, and color for a variety of viewing environments and image types. You can select a mode designed to match your image and environment, or experiment with the available modes.

  • Page 84: Changing The Color Mode

    4. To cycle through all the available Color Modes for your input signal, press the Color Mode button repeatedly. Parent topic: Color Mode Available Color Modes You can set the projector to use these Color Modes, depending on the input source you are using: Color Mode Presentation Description Best for color presentations in a bright room...

  • Page 85: Turning On Auto Iris

    In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Menu button.

  • Page 86: Controlling The Volume With The Volume Buttons

    2. Press the Volume buttons as necessary to lower or raise the volume. A volume gauge appears on the screen. 3. To set the volume to a specific level for an input source, you can set the volume using a projector menu.

  • Page 87: Projecting A Slide Show

    Projecting a Slide Show You can use your projector's Slideshow feature whenever you connect a USB device that contains compatible image files. This lets you quickly and easily display a slide show or presentation, and control it using the projector's remote control.

  • Page 88: Starting A Slide Show Or Presentation

    Projecting a Slide Show Starting a Slide Show or Presentation After connecting a USB device to the projector, you can switch to the USB input source and start your slide show or presentation. Note: You can change the Slideshow operation options or add special effects by highlighting Option at the bottom of the screen and pressing Enter.
  • Page 89 • To move to the next or previous image, press the left or right arrow button. 5. To stop the display, follow the on-screen instructions or press the Esc button. Slideshow Display Options Parent topic: Projecting a Slide Show Related tasks Disconnecting a USB Device or Camera From the Projector...

  • Page 90: Slideshow Display Options

    Slideshow Display Options You can select these display options when using the projector's Slideshow feature. Option Display order Sort Order Continuous Play Screen switching time Effect Available settings Description Name order Displays files in name order Date order Displays files in date order...
  • Page 91 Parent topic: Starting a Slide Show or Presentation...

  • Page 92: Adjusting Projector Features

    Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture and Sound Temporarily Stopping Video Action Temporarily Zooming Into and Out of Images Projector Security Features Projector Identification System for Multiple Projector Control...

  • Page 93: Stopping Video Action Temporarily

    2. To restart the video action in progress, press Freeze again. Parent topic: Adjusting Projector Features Zooming Into and Out of Images You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it...

  • Page 94: Projector Security Features

    Adjusting Projector Features Projector Security Features You can secure your projector to prevent theft or unintended use by setting up the following security features: • Password security to prevent the projector from being turned on, and prevent changes to the startup screen and other settings.

  • Page 95: Password Security Types

    Password Security Types You can set up these types of password security using one shared password: • Power On Protect password prevents anyone from using the projector without first entering a password. • User's Logo Protect password prevents anyone from changing the custom screen the projector can display when it turns on or when you use the A/V Mute feature.

  • Page 96: Selecting Password Security Types

    You see the prompt "Change the password?". 3. Select Yes and press Enter. 4. Hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 5.

  • Page 97: Entering A Password To Use The Projector

    If you do not see this menu, hold down the Freeze button on the remote control for five seconds until the menu appears. 1. To prevent unauthorized use of the projector, select Power On Protect, press Enter, select On, press Enter again, and press Esc.
  • Page 98 • You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed. • If the password is incorrect three times, you see a message that the projector is locked and a request code. Write down the code, turn the projector off, and disconnect the power cord from the projector.

  • Page 99: Saving A User's Logo Image To Display

    Saving a User's Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on. You can also display the image when the projector is not receiving an input signal or when you temporarily stop projection (using the A/V Mute feature).
  • Page 100 You see a prompt asking if you want to save the image as the User's Logo. 8. Select Yes and press Enter. Note: It takes a few moments for the projector to save the image; do not use the projector, its remote control, or any connected equipment until it is finished.

  • Page 101: Locking The Projector's Buttons

    Locking the Projector's Buttons You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You can lock all the buttons or all the buttons except the power button. 1. Press the Menu button.

  • Page 102: Installing A Security Cable

    • Use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson. • Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture.

  • Page 103: Setting The Projector Id

    Setting the Remote Control ID The remote control's ID is set to zero by default so it can operate any compatible projector. If you want to set the remote control to operate only a particular projector, you need to set the remote control's ID to match the projector's ID.

  • Page 104: Matching Multiple-Projector Display Quality

    2. Set ID numbers on each projector. 3. Make sure all the projectors are using the same Color Mode setting. 4. It is best to match two projectors at a time, so set the remote control ID to match the first projector.
  • Page 105 13. Adjust the Color Correct. settings for green-to-red (G/R) and blue-to-yellow (B/Y) balance for all the levels on both projectors in the same way. 14. If you need to match more projectors, repeat these steps matching projector 3 to projector 2, 4 to 3, and so on.

  • Page 106: Projecting Two Images Simultaneously

    Projecting Two Images Simultaneously You can use the split screen feature to simultaneously project two images from different image sources next to each other. You can control the split screen feature using the remote control or the projector menus. Note: While you use the split screen feature, other projector features may not be available and some settings may be automatically applied to both images.
  • Page 107 Note: Select Auto to hear audio from the largest screen or the left screen. 7. To exit the split screen feature, press the Split or Esc button. Parent topic: Adjusting Projector Features Related references Input Signal Settings - Signal Menu...

  • Page 108: Adjusting The Menu Settings

    Projector Reset Options - Reset Menu Using the Projector's Menus You can use the projector's menus to adjust the settings that control how your projector works. The projector displays the menus on the screen. 1. Press the Menu button on the control panel or remote control.
  • Page 109 You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3.

  • Page 110: Image Quality Settings - Image Menu

    8. Press Menu or Esc to exit the menus. Parent topic: Adjusting the Menu Settings Image Quality Settings - Image Menu Settings on the Image menu let you adjust the quality of your image for the input source you are currently using.

  • Page 111: Input Signal Settings - Signal Menu

    Available Color Modes Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. The available settings depend on the currently selected input source.
  • Page 112 Note: You can restore the default settings of the Position, Tracking, and Sync settings by pressing the Auto button on the remote control. To change settings for an input source, make sure the source is connected and select that source. Setting Options Auto Setup...
  • Page 113 Setting Options Position Up, down, left, right Progressive Video Film/Auto Noise Reduction HDMI Video Range Normal Expanded Auto Input Signal Auto Component Video Signal Auto Various video standards Description Adjusts the image location on the screen Sets whether to convert interlaced-to-progressive signals for certain video image types Off: for fast-moving video images...

  • Page 114: Projector Feature Settings - Settings Menu

    Adjusting the Menu Settings Related references Available Image Aspect Ratios Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features. Options Description See the list of available aspect Sets the aspect ratio (width-to-...
  • Page 115 Changes the shape of the remote control pointer feature Selects the brightness mode of the projector lamp Normal: sets maximum lamp brightness ECO: reduces lamp brightness and fan noise, and saves power and lamp life Adjusts the volume of projector’s speaker system or external speakers...

  • Page 116: Projector Setup Settings - Extended Menu

    Parent topic: Adjusting the Menu Settings Related tasks Projecting Two Images Simultaneously Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Options Description Front Limits reception of remote control signals by the selected receiver;...
  • Page 117 Startup Screen: controls whether a special screen appears when the projector starts A/V Mute: selects the screen color or logo to display when A/V Mute is turned on Controls use of closed captions...
  • Page 118 Direct Power On: lets you turn on the projector without pressing the power button Sleep Mode: automatically turns off the projector after an interval of inactivity Sleep Mode Timer: sets the interval for Sleep Mode Trigger Out: outputs a DC 12V signal from the 3.5 mm mini-jack...

  • Page 119: Projector Network Settings - Network Menu

    Multi-screen Language Parent topic: Adjusting the Menu Settings Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network. Options Description Clean Notice...
  • Page 120 Setting Options Net. Info - Wireless LAN Connection mode Antenna level Projector Name SSID DHCP IP Address Subnet Mask Gateway Address MAC Address Region Code Net. Info - Wired LAN Projector Name DHCP IP Address Subnet Mask Gateway Address MAC Address...

  • Page 121: Projector Information Display - Info Menu

    Wireless Network Projection Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. Note: Available settings depend on the current input source. The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours.

  • Page 122: Event Id Code List

    Event ID code Cause and solution 0432 The EasyMP Network Projection program did not start. Turn the projector off and then on again. 0435 Description Displays the name of the port to which the current input source is...

  • Page 123: Projector Reset Options - Reset Menu

    If that does not solve the problem, contact 0899 Epson for help. Parent topic: Projector Information Display - Info Menu Projector Reset Options - Reset Menu You can reset most of the projector settings to their default values using the Reset All option on the Reset menu.
  • Page 124 You can also reset the projector's lamp usage timer to zero when you replace the lamp using the Reset Lamp Hours option. You cannot reset the following settings using the Reset All option: • Input Signal • User's Logo • Language •...

  • Page 125: Maintaining And Transporting The Projector

    Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation. The only parts you should replace are the lamp, air filter, and remote control batteries. If any other part needs replacing, contact Epson or an authorized Epson servicer.

  • Page 126: Cleaning The Projector Case

    Air Filter and Vent Maintenance The projector's air filter keeps the intake air clean, and its vents expel the exhaust. If dust collects on the air filter or vents, clean them as described in this manual. Dust clogs may cause the projector to overheat due to improper ventilation.

  • Page 127: Cleaning The Air Filter

    Projector Maintenance Cleaning the Air Filter Be sure to clean the projector's air filter if it gets dusty, if you see a message telling you to clean it, or if the Filter light flashes green. 1. Turn off the projector and unplug the power cord.
  • Page 128 2. Press down on the tabs on the air filter cover and open the cover. 3. Pull the air filter out of the projector.
  • Page 129 4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. 5.

  • Page 130: Replacing The Air Filter

    Note: You must install an air filter or the projector will turn off after about one minute. You can replace the air filter while the projector is mounted to the ceiling, if necessary. The illustrations below show the projector placed on a table.
  • Page 131 2. Press down on the tabs on the air filter cover and open the cover. 3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.

  • Page 132: Projector Lamp Maintenance

    Related references Projector Light Status Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system. Replace the lamp as soon as possible when the following occurs: •...

  • Page 133: Replacing The Lamp

    Projector Lamp Specifications Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the projector is mounted to the ceiling, if necessary.
  • Page 134 4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
  • Page 135 The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Press the handle down.
  • Page 136 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage. Parent topic: Projector Lamp Maintenance...

  • Page 137: Resetting The Lamp Timer

    Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information.

  • Page 138: Replacing The Remote Control Batteries

    Replacing the Remote Control Batteries The remote control uses the two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries.
  • Page 139 Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Related references Remote Control Operation...

  • Page 140: Transporting The Projector

    • Remove any equipment connected to the projector. • When transporting the projector a long distance or as checked luggage, pack it in a firm box with cushioning around it and mark the box "Fragile". • When shipping the projector for repairs, place it in its original packing materials, if possible, or use equivalent materials with cushioning around the projector.

  • Page 141: Solving Problems

    Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it If this does not solve the problem, check the following: • The lights on the projector's control panel may indicate what the problem is.
  • Page 142 Orange Flashing orange Off Filter light Status and solution Normal operation. Warming up. Wait for an image to appear. Standby or sleep mode. Preparing network monitoring or shutting down. (Wait for the light to remain orange before unplugging the projector.)
  • Page 143 • If overheating continues, replace the air filter. • If the problem persists, unplug the projector and contact Epson for help. Lamp has a problem. • Check to see if the lamp is burned out, broken, or installed incorrectly. Reseat or replace the lamp as necessary.
  • Page 144 Replace the lamp right away to avoid damage. Do not continue using the projector. A fan or sensor has a problem. Turn the projector off, unplug it, and contact Epson for help. Internal projector error or air exhaust vent error. Turn the projector off, unplug it, and contact Epson for help.

  • Page 145: Using The Projector Help Displays

    Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and contact Epson for help. Parent topic: Solving Problems Related references Projector Setup Settings - Extended Menu Where to Get Help...

  • Page 146: Solutions When No Image Appears

    • Press the projector's power button to wake it from standby or sleep mode. Also see if your connected computer is in sleep mode or displaying a blank screen saver. • If you unplugged the projector and plugged it right back in, press the power button to turn on the projector (with Direct Power On enabled).

  • Page 147: Solutions When "No Signal" Message Appears

    2. To display on both the laptop's monitor and the projector, try pressing the same keys again. 3. If the same image is not displayed by the laptop and projector, check the Windows Display utility to make sure the external monitor port is enabled. (See your computer or Windows manual for instructions.)

  • Page 148: Solutions When "Not Supported" Message Appears

    • Make sure the correct input signal is selected on the Signal menu. • Make sure the computer's display resolution does not exceed the projector's resolution and frequency limit. If necessary, select a different display resolution for your computer. (See your computer manual for details.)

  • Page 149: Solutions When The Image Is Not Rectangular

    If the projected image is not evenly rectangular, try the following solutions: • Place the projector directly in front of the center of the screen, facing it squarely, if possible. • If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape.

  • Page 150: Solutions When The Image Is Fuzzy Or Blurry

    • Adjust the image focus. • Check the projector lens cover glass for condensation. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it.

  • Page 151: Solutions When The Image Brightness Or Colors Are Incorrect

    Contrast, Tint, Color Adjustment, and/or Color Saturation. • Make sure you selected the correct input source on the Signal menu. • Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables.

  • Page 152: Solutions When There Is No Sound Or Low Volume

    Solving Problems Solutions to Projector Power or Shut-Off Problems If the projector does not come on when you press the power button or shuts off unexpectedly, try the following solutions: • Make sure the power cord is securely connected to the projector and to a working electrical outlet.

  • Page 153: Solutions To Problems With The Remote Control

    • If the power button on the remote control does not turn on the projector, check its batteries and make sure the Remote Receivers setting is turned on in the projector's menus. Parent topic: Solving Projector or Remote Control Operation Problems...

  • Page 154: Solutions To Password Problems

    • If you have entered an incorrect password too many times and see a message displaying a request code, write down the code and contact Epson. • If you lose the remote control you cannot enter a password. Order a new one from Epson. Parent topic:...
  • Page 155 To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card. This is the fastest way of speaking to a live representative, and it's free. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period.

  • Page 156: Technical Specifications

    Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dimension Specifications Projector Electrical Specifications Projector Environmental Specifications Projector Safety and Approvals Specifications Supported Video Display Formats General Projector Specifications...
  • Page 157 White light output 3200 lumens (ISO 21118 standard) Contrast ratio 2000:1 with Auto Iris On, Dynamic Color mode, and Normal Power Consumption mode Image size PowerLite D6150/D6250: 30 to 300 inches (0.8 to 7.6 m) PowerLite D6155W: 29 to 280 inches (0.7 to 7.1 m) Projection distance PowerLite D6150/D6250: 2.69 to 45.44 feet (0.82 to 13.85 m)

  • Page 158: Projector Lamp Specifications

    Keystone correction angle USB Type B port compatibility USB 1.1 and 2.0 compliant for using remote control as wireless USB Type A port compatibility USB 1.1 and 2.0 compliant port for USB device input or Epson Parent topic: Technical Specifications...

  • Page 159: Remote Control Specifications

    Lamp life Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Parent topic: Technical Specifications Remote Control Specifications...

  • Page 160: Projector Electrical Specifications

    Parent topic: Technical Specifications Projector Electrical Specifications Rated frequency Power supply Power consumption (110 to 120 V) PowerLite D6150: 9.3 lb (4.2 kg) PowerLite D6155W/D6250: 9.7 lb (4.4 kg) 50/60 Hz 110 to 240 VAC ±10% PowerLite D6150: 3.0 to 1.5 A PowerLite D6155W/D6250: 3.6 to 1.8 A...

  • Page 161: Projector Environmental Specifications

    Projector Safety and Approvals Specifications United States Canada Parent topic: Technical Specifications Operating: PowerLite D6150: Normal Power Consumption mode: 316 W ECO Power Consumption mode: 235 W PowerLite D6155W/D6250: Normal Power Consumption mode: 380 W ECO Power Consumption mode: 311 W Standby (all models): 0.38 W (Communication Off), 6.5 W (Communication On)

  • Page 162: Supported Video Display Formats

    For best results, your computer monitor or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically.
  • Page 163 Display format Refresh rate (in Hz) TV (NTSC) TV (PAL) 50/60 TV (SECAM) Component video SDTV (480i) SDTV (576i) SDTV (480p) SDTV (576p) HDTV (720p) 50/60 HDTV (1080i) 50/60 HDMI input signals SVGA WXGA SXGA SXGA+ UXGA SDTV (480i/480p) SDTV (576i/576p) HDTV (720p) 50/60 HDTV (1080i)

  • Page 164: Notices

    • Do not look into the lens when the projector is on. The bright light can damage your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 30° forward or back.
  • Page 165 • Do not overload wall outlets, extension cords, or power strips. Do not insert the plug into a dusty outlet. This can cause fire or electric shock. • Do not place the projector where the cord can be walked on. This may result in fraying or damage to the plug.
  • Page 166 • Do not use the projector where it may be exposed to excessive dust, smoke, or corrosive gases. • Do not use or store the projector or remote control in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle.

  • Page 167: Fcc Compliance Statement

    If you do inhale gases or gases come in contact with your eyes or mouth, seek medical advice immediately. • If the projector is mounted overhead and the lamp breaks, be careful to prevent pieces of glass from falling into your eyes when you open the lamp cover.

  • Page 168: Trademarks

    HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. Parent topic: Notices ®...

  • Page 169: Software Copyright

    We provide the source code of the GPL Programs until five (5) years after the discontinuation of same model of this projector product. If you desire to receive the source code of the GPL Programs, please see the "EPSON Projector Contact List" in the User's Guide, and contact the customer support of your region.
  • Page 170 Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it.
  • Page 171 Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program).
  • Page 172 In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
  • Page 173 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein.
  • Page 174 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
  • Page 175 We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same model of this projector product. If you desire to receive the source code of the LGPL Programs, please see the "EPSON Projector Contact List" in the User's Guide, and contact the customer support of your region.
  • Page 176 These LGPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. The list of LGPL Programs is as follows and the names of author are described in the source code of the LGPL Programs.
  • Page 177 To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you.
  • Page 178 In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non- free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
  • Page 179 You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library.
  • Page 180 Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
  • Page 181 during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above);...
  • Page 182 b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License.
  • Page 183 12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded.
  • Page 184 That's all there is to it! BSD License (Berkeley Software Distribution License) This projector product includes the open source software program "University of California, Berkeley License (Berkeley Software Distribution License)" which applies the terms and conditions provided by owner of the copyright to the "BSD License".
  • Page 185 SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. libjpeg This projector product includes the open source software program "libjpeg" which applies the terms and conditions provided by owner of the copyright to the "libjpeg". The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  • Page 186 License terms of conditions of each program which are provided by owner of the copyright to the "libjpeg" are as follows. Copyright ©) 1994-1997, Thomas G. Lane . This file is part of the Independent JPEG Group's software. For conditions of distribution and use, see the accompanying README file. This distribution contains the sixth public release of the Independent JPEG Group's free JPEG software.
  • Page 187 Service Mark property of CompuServe Incorporated." libpng This projector product includes the open source software program "libpng" which applies the terms and conditions provided by owner of the copyright to the "libpng". The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  • Page 188 License terms of conditions of each program which are provided by owner of the copyright to the "libpng" are as follows. For conditions of distribution and use, see copyright notice in png.h Copyright ©) 1998-2004 Glenn Randers-Pehrson (Version 0.96 Copyright ©) 1996, 1997 Andreas Dilger) (Version 0.88 Copyright ©) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.) This copy of the libpng notices is provided for your convenience.
  • Page 189 John Bowler Kevin Bracey Sam Bushell Magnus Holmgren Greg Roelofs Tom Tanner libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright ©) 1995, 1996 Guy Eric Schalnat, Group 42, Inc. For the purposes of this copyright and license, "Contributing Authors" is defined as the following set of individuals: Andreas Dilger Dave Martindale...
  • Page 190 September 12, 2004 zlib This projector product includes the open source software program "zlib" which applies the terms and conditions provided by owner of the copyright to the "zlib". The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  • Page 191 This projector product includes the open source software program "libmd5-rfc" which applies the terms and conditions provided by owner of the copyright to the "libmd5-rfc". The "libmd5-rfc" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  • Page 192 C++ compilation from Martin Purschke <purschke@bnl.gov>. 1999-05-03 lpd Original version. mDNSResponder This projector product includes the open source software program "mDNSResponder" which applies the following license terms "Apache License Version 2.0, January 2004". List of "mDNSResponder" mDNSResponder-107.6 (only mDNSResponderPosix is used) License terms "Apache License Version 2.0, January 2004"...
  • Page 193 otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity. "You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License. "Source" form shall mean the preferred form for making modifications, including but not limited to software source code, documentation source, and configuration files.
  • Page 194 (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is filed.
  • Page 195 WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your exercise of permissions under this License.

  • Page 196: Copyright Notice

    Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

This manual is also suitable for:

Powerlite d6155Powerlite d6155wPowerlite d6250

Table of Contents