Control/Circuit Terminal Block - GE Fuji Electric AF-300 MICRO-SAVER II Instructions Manual

Table 4:
Wire Size Recommendations
& Circuit Protection Ratings
240V – Single Phase and 230V Three Phase
Model PH HP
NEMA 1 NEMA 4 Const Carrier Frequency
Input TRQ
6KM$221F25N1A1 6KM$221F25X4A1 1 1/4
6KM$221F50N1A1 6KM$221F50X4A1 1 1/2
6KM$221001N1A1 6KM$221001X4A1 1 1
6KM$221002N1A1 6KM$221002X4A1 1 2
6KM$221003N1A1 6KM$221003X4A1 1 3
6KM$223F25N1A1 6KM$223F25X4A1 3 1/4
6KM$223F50N1A1 6KM$223F50X4A1 3 1/2
6KM$223001N1A1 6KM$223001X4A1 3 1
6KM$223002N1A1 6KM$223002X4A1 3 2
6KM$223003N1A1 6KM$223003X4A1 3 3
6KM$223005N1A1 6KM$223005X4A1 3 5
480V – Three Phase
Model PH HP
NEMA 1 NEMA 4 Const Carrier Frequency
Input TRQ
6KM$243F50N1A1 6KM$243F50X4A1 3 1/2
6KM$243001N1A1 6KM$243001X4A1 3 1
6KM$243002N1A1 6KM$243002X4A1 3 2
6KM$243003N1A1 6KM$243003X4A1 3 3
6KM$243005N1A1 6KM$243005X4A1 3 5
WARNING - Device ratings such as system coordination, short-circuit
rating and type must be carefully reviewed by the user.
NOTE: Wire size from NEC table 310-16. Copper wire rated 60° C for 100 amps or less,
75° C for over 100 amps in 30° C ambient and 1.25 times Drive rated amps. These
are minimum wire sizes; consult and conform to local and national codes.
* NOTE: AC input fuses are required to validate the drive's UL and CSA approvals.
The fuse should be Class J type such as Bussman, JKS or equivalent. Circuit breaker
ratings are shown for reference, but UL and CSA approval can only be validated by
the use of Class J fuses.
** Optional Item.
DB Incoming Power
Output Current Power Resistor** AC – Line Devices
Wire Wire Circuit
Low High AWG AWG Fuses* Breaker
1.5 1.3 16 - 6
3 2.5 16 16 10
5 4 14 14 15
8 7 12 12 20
11 10 10 10 30
1.5 1.3 16 - 6
3 2.5 16 16 10
5 4 16 16 15
8 7 14 14 20
11 10 14 14 30
17 16.5 10 10 40
DB Incoming Power
Output Current Power Resistor** AC – Line Devices
Wire Wire Circuit
Low High AWG AWG Fuses* Breaker
1.6 1.4 16 14 6
2.5 2.1 16 14 6
3.7 3.7 16 14 15
5.5 5.3 16 14 15
9.0 8.7 14 14 20
4-4
30A 30B Y1 FMA PLC BX RST C1 13 12 11
5
10
15
20
30
5
5
10
15
20
30
5
5
10
15
15
* Not available on 6KM$221F25X1A1, 6KM$221F25A4A1, 6KM$223F25X1A1, 6KM$223F25A4A1.
Figure 4-5.
30C FMP X1 X2 X3 X4 REV FWD THR CM
*
* Factory installed jumper
CONTROL CIRCUIT TERMINAL BLOCK LAYOUT
#1 CAUTION:
Remove jumper from between terminals THR and CM when
a motor overload or a motor temperature switch is used.
Wire the device thermal switch in series with the THR and
CM terminals.
#2 NOTE:
FWD to CM jumper required for operation using keypad
RUN-STOP.
Figure 4-4.
L1 L2 L3 P1 P(+) DB* U V W
DB
E(G)
RESISTOR
DYNAMIC BRAKING RESISTOR CONNECTIONS
4-5
* #1 #2