Advertisement
Camera Diagrams
BL-C111
Front View
A
Lens housing
A
(pan/tilt mechanism)
B
Lens
B
C
Indicator
C
PRIVACY button
D
Built-in sensor
D
(pyroelectric infrared
sensor)
E
E
Microphone
*1
See 1.1 Understanding the Camera Indicator in the Troubleshooting Guide on the CD-ROM for indicator meaning.
*2
See "PRIVACY Button" on page 4 for information about the PRIVACY button.
BL-C131
Front View
A
Antenna
B
Lens housing
A
(pan/tilt mechanism)
B
C
Lens
C
D
Indicator
PRIVACY button
D
E
Built-in sensor
E
(pyroelectric infrared
sensor)
F
F
Microphone
*1
See 1.1 Understanding the Camera Indicator in the Troubleshooting Guide on the CD-ROM for indicator meaning.
*2
See "PRIVACY Button" on page 4 for information about the PRIVACY button.
Connections
Connect the camera to your router and to the power outlet as described below.
• Before proceeding, confirm that your PC is connected to your router and can access the Internet. Also confirm that your router's UPnP
enabled. (Most routers have UPnP
Camera website (http://panasonic.net/pcc/ipcam/) for more information.
• The camera illustrations in this document depict the BL-C131.
WIRELESS/WIRED switch
Bottom of BL-C131
Router
Internet
Modem
After the camera's indicator turns green, you may set up the camera. Continue by following the procedure described
in the included Setup Guide.
• If the indicator does not turn green, see 1.2 Camera Indicator Issues in the Troubleshooting Guide on the included CD-ROM.
2
Bottom View
*1
/
*2
Bottom View
*1
/
*2
™
turned off by default.) Refer to the operating instructions included with your router or to the Panasonic Network
LAN cable
(Cat-5 straight cable)
PC
F
Tripod mounting hole
F
G
FACTORY DEFAULT
G
RESET button
H
LAN port
I
DC IN jack
H
J
MAC address label
I
K
Serial number label
J
K
G
Tripod mounting hole
H
FACTORY DEFAULT
G
RESET button
H
I
WIRELESS/WIRED
I
switch
J
J
LAN port
K
K
DC IN jack
L
MAC address label
L
M
Serial number label
M
1
2
3
4
To the
power
outlet
AC adaptor
Rear View
L
Tripod mounting hole
M
Wall mounting holes
L
M
Rear View
N
Tripod mounting hole
O
Wall mounting holes
N
O
BL-C131 only: Confirm that the WIRELESS/
WIRED switch on the bottom of the camera
is set to WIRED.
Connect the LAN cable to the camera and
the router.
Connect the AC adaptor cord to the DC IN
jack.
Plug the AC adaptor into the power outlet.
• The lens will pan and tilt when the camera
is turned on.
• Confirm that the indicator lights green
after about 1 minute. If the indicator does
not light green, see 1.2 Camera Indicator
Issues in the Troubleshooting Guide on
the CD-ROM.
Green
• The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the product and is
easily accessible.
• Use only specified Panasonic AC adaptor
(BL-C111CE/BL-C131CE: model no.
PQLV206CE [order no. PQLV206CEY],
BL-C111E/BL-C131E: model no.
PQLV206E [order no. PQLV206EY]).
• When the lens pans or tilts, a sound can
be heard from the camera. This is normal.
• The camera may become warm. This is
normal.
™
feature is
Advertisement
