Setting Up The Unit - Panasonic EP1082 Operating Instructions Manual

SETTING UP THE UNIT

WHERE TO USE THE UNIT
Keep at least 10 cm away from the wall.
Approx. 147 cm
Approx.
Width
30 cm
approx. 70 cm
Mat
Area where the unit
touches the floor
1 UNPACK THE UNIT AND RAISE THE BACKREST
CAUTION
• When raising the backrest, be careful not to get your hands caught between the backrest and the backrest latch or
the backrest and the armrests.
Failure to follow this precaution may result in injury.
Backrest latch
Check that there
is nothing
around the unit.
2 INSPECT THE CONTENTS
Massage Lounger Pillow
Armrests — 2
GB7
7-8
• Avoid places where the unit will be exposed to direct sunlight
for long periods of time or places where it will be exposed to
high temperatures, such as in front of a heater, etc., as this
can cause discoloration or hardening of the leather.
• Placing a mat or cloth under the unit is recommended to
prevent floor damage. The size of the mat should be sufficient
(at least 107 cm × 70 cm).
• Set the unit near the electrical outlet.
See Warning No. 11 and 12 on page GB1.
1 Remove the top of the carton.
• When packed for shipping the backrest is folded forward.
2 Remove the packing and cushioning
materials and take out all accessories.
3 Raise the backrest.
• Do not connect the power cord to an electrical outlet during setup.
• Hold the backrest with both hands and lift in the direction of the
arrow until it comes to a stop.
• Take care that the cords for power and controller are not caught
the backrest and seat.
Back Cushion Allen Key — 1 Lock Switch Key — 1
Attachment Screws — 8
• The lock switch key has
been inserted in the
lock switch prior to
leaving the factory.
3 HOW TO MOVE THE UNIT
Using the wheels to move the unit
• Hold the backrest to move the unit when using the wheels.
• It is easier to move the unit with the massage heads
retracted and the backrest in the upright position.
* Place a mat or cloth on the floor and move the unit slowly
to prevent floor damage.
Move it slowly
Wheels
4 INSTALL THE ARMRESTS ON THE UNIT
Left
Back
Front
Zipper
Fastener
Convex
Round hole
Front Rear
Lift up
Secure with screws
Allen key
Lifting the Unit
• Move the unit by having 2 persons hold the armrests.
* Please hold the armrests securely to avoid dropping the
unit as it may damage your floor.
1 Install the armrests.
1 Unfasten the fastener.
2 Unzip the zipper of the armrest completely.
3 Make sure to confirm the side (left or right) and
direction (front or back) for each armrest.
The illustration shows the left armrest. The right armrest
is stamped "Front", "Right" and "Back".
* The left armrest must be installed on the left hand side of
the unit.
4 Align the proper armrest with the unit and connect.
Be careful not to catch the fabric between the chair
and the armrest.
2 Secure the armrests with attachment
screws.
(Total of 4 positions for a single armrest)
Lift the fabric on the side of the armrest and insert the
attachment screw onto the end of the Allen key, and
then fasten.
(Tighten the screws in the 4 positions lightly at first, and
then fasten all screws firmly.)
* If the screw does not enter into the hole, fasten the screw
while pressing the armrest down from the top.
3 Close the zipper at the bottom side of
the armrests.
When closing the zipper, be careful not to twist the end of
the zipper.
1 Set the zipper.
2 Zip the zipper.
4 Put both ends of the zipper inside the
armrest.
1 Turn in the edge of the zipper.
2 Fix the sliding tab of the zipper with the fastener.
2008/04/08
GB8
11:21:51