Advertisement
A
B
"DVD-TEMP" is
indicated on the LCD.
"SYS-TEMP" is
indicated on the LCD.
"CHK MODE" is
indicated on the LCD.
"RUNNING" is
indicated on the LCD.
"MEMCHECK" is
indicated on the LCD.
"INIT" is
indicated on the LCD.
1-38 (No.MA308)
Detailed error code (2 bytes)
First byte
Higher 4 bits
Lower 4 bits
[1] Time out
[2] Switch status error
[3] Swinging error
. . . .
Second byte
bit7
. . . .
bit6,5
. . . .
bit4
. . . .
bit3
. . . .
bit2
. . . .
bit1
. . . .
bit0
(Example) When a switch status error occurs during loading route 3 and
the switch status is L/L/H/H/H (00111B = 07H), the error code
and detailed error code become: [09 3207].
Route No.(EJECT route No.)
-
1(2)
1(2)
2(2)
2(2)
2(2)
2(2)
3(1)
3(1)
Chart 1.1 12cm Disc switch status transition
Route No.(EJECT route No.)
-
1(2)
1(2)
2(2)
2(2)
3(1)
3(1)
*Transition in the center loading (Similar to 12cm in the side loading)
Press the [SEL] key
Press the [SEL] key
Press the [SEL] key
Press the [SEL] key
Press the [SEL] key
Press the [SEL] key
*Displayed with loading/ejection error only.
. . . .
Route NO. (Process of error occurrence)
Refer to charts 1.1 and 1.2.
. . . .
Error type
Disc type (0: 12 cm. 1: 8 cm)
Fixed at 0
SW 1 status
SW 2 status
SW 3 status
SW 1 status
RESET SW status
SW1/2/3/4 [Rest SW]
Loading
1,1,1,1
[0]
No Disc
0,1,1,1
[0]
Disc insert
detection
0,0,1,1
[0]
0,0,0,1
[0]
0,0,1,1
[0]
0,1,1,1
[0]
1,1,1,1
[0]
1,1,1,0
[0]
[1]
1,1,1,0
Load completion
Loading *
SW1/2/3/4 [Rest SW]
1,1,1,1
[0]
No Disc
0,1,1,1
[0]
Disc insert
detection
0,0,1,1
[0]
0,1,1,1
[0]
1,1,1,1
[0]
1,1,1,0
[0]
1,1,1,0
[1]
Load completion
Chart 1.2 8cm Disc switch status transition
Thermistor's temperature data readout
: Data in the temperature sensor in the DVD unit
is read every 5 seconds and displayed in hex numbers.
Thermistor's temperature data readout
: Data in the temperature sensor in the system control
is read every 5 seconds and displayed in hex numbers.
DVD unit check mode
(See section "DVD unit check mode" for details.)
Running mode: For use in running tests.
Memory check
: The remaining data capacity of the disc is
displayed on the LCD.
Initialize user set data
: The system control EEPROM is initialized except
for the loading/ejection error history.
Eject
Reload
No Disc
Disc push in
Eject
completion
Reload start
Eject start
Load completion
Eject
Reload
No Disc
Disc push in
Eject
completion
Reload start
Eject start
Load completion
Advertisement
