Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Toro Reelmaster 2000 Series
Summary of Contents for Toro Reelmaster 2000 Series
- Page 1 Form No. 3328–881 5, 8 and 11 Blade Cutting Unit Reelmaster 2000/3000 Series Model No. 03210—230000001 and Up Model No. 03212—230000001 and Up Model No. 03237—230000001 and Up Model No. 03238—230000001 and Up Model No. 03239—230000001 and Up Operator’s Manual English (EN, GB)
-
Page 2: Table Of Contents
........Dealer or Toro Customer Service and have the model and serial numbers of your product ready. -
Page 3: Safety
Safety Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. Part No. 67-7960 Part No. 93-6688 (for CE) 1. -
Page 4: Optional Equipment
Optional Equipment Full Roller Scraper Kit* (27 in.) Part No. 60-9560 Full Roller Scraper Kit* (32 in.) Model No. 03478 Basket Kit* (27 in.) Model No. 03227 Comb Kit* Part No. 67-9400 High Height of Cut (Extension) Part No. 104-1395 Fixed Kit* Part No. -
Page 5: Set-Up
Operator’s manual Read before operating. Parts catalog Registration card Fill out and return to Toro. After the cutting unit is unboxed, use the following procedures to ensure the cutting units are adjusted properly. 1. Check each end of the reel for grease. Grease should be visibly evident in the reel bearings. -
Page 6: Adjusting Front Shield
Adjusting Bedknife Parallel to 5. Hold one roller bracket stationary and use other bracket as a wrench to loosen or tighten bearing Reel clearance to allow roller to rotate freely and to eliminate bearing end play. 1. A 3/4 in. (19 mm) wrench will be needed to rotate Important bedknife adjustment knob. -
Page 7: Setting Height Of Cut And Leveling Rear Roller
Setting Height of Cut and 6. Loosen the two locknuts securing the bedbar adjuster to the cutting unit side plate (Fig. 5). Leveling Rear Roller 1. Position cutting unit on a surface plate. 2. Adjust support capscrew to achieve 1 in. 1/16 (25mm 1.5mm) dimension between height-of-cut... -
Page 8: Verifying The Height-Of-Cut Setting And Leveling The Front Roller
This measurement is from bar face to cutting unit will cut one thickness of newspaper across its underside of screw head. Gauge Bar (Part No. entire width (paper to be perpendicular to bedknife) 98–1852) may be obtained from your local Toro (Fig. 10). Distributor. Figure 10 Figure 9 1. -
Page 9: Changing Height-Of-Cut
This measurement is from bar face to underside of screw head. Gauge Bar (Part No. This procedure describes how to change the height-of-cut 98–1852) may be obtained from your local Toro after a cutting unit has been set up as described in Setup, Distributor. - Page 10 Toro part no. 98-1852 (Fig. 12). The first screw is set given height-of-cut. for height-of-cut, and the second screw is set for cutting unit attitude.
-
Page 11: Cutting Unit Attitude
3. Place the gauge bar across the front and rear rollers. 4. Adjust the second screw to contact the bedknife. The first screw head needs to fit snugly over the edge 5. Place an angle indicator on the gauge bar and record of the bedknife while the gauge bar contacts the rollers the gauge bar angle (Fig. -
Page 12: Operation
Operation 2. Slowly rotate reel in reverse direction listening for reel-to-bedknife contact. If no contact is evident, turn bedknife adjusting knob clockwise, one click at a time, Note: Determine the left and right sides of the machine until light contact is felt and heard. from the normal operating position. -
Page 13: Lubrication
Lubrication Each cutting unit has 6 grease fittings (with optional front roller installed) that must be lubricated regularly with No. 2 General Purpose Lithium Base Grease. The grease fitting locations and quantities are: Bedknife adjuster (2), every 50 hours (Fig. 15); Reel bearings (2) and front and rear rollers (2 ea.) (Fig. -
Page 14: Backlapping
Note: Additional instructions and procedures on Backlapping are available in the Toro Sharpening Reel & Rotary Mowers Manual, Form No. 80-300SL. Note: For a better cutting edge, run a file across the front face of the bedknife when the lapping operation is completed. -
Page 16: The Toro General Commercial Products Warranty
If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.