Sealey SA1007 Quick Start Manual

Thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instruction gloves
manual
1. sAFETY
NOTE: Follow all workshop health & safety rules, regulations, and conditions when using drill.
WARNING! disconnect from air supply before changing accessories or servicing.
‰
WARNING! DO NOT use drill if damaged or faulty. Contact your local service agent.
‰
WARNING! Beware of high-reaction torque when breaking through the material being drilled.
‰
WARNING! Check correct air pressure is maintained and not exceeded. We recommended 80 psi.
‰
maintain the drill in good condition and replace any damaged or worn parts. Use genuine parts only. non-authorised parts may be
9
dangerous and will invalidate the warranty.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Wear approved safety eye protection. If dust is generated wear respiratory protection, and safety gloves.
9
Wear suitable clothing to avoid snagging. Keep hands away from rotating chuck and drill bit.
9
Keep drill bits clean and sharp for best and safest performance.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
ensure the chuck is securely fastened to the spindle and the drill bit is secure in the chuck.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT get the drill wet or use in damp or wet locations.
8
DO NOT apply excessive loads to the drill bit during operation.
8
DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
8
DO NOT use the drill for a task it is not designed to perform.
8
DO NOT use drill unless you have been instructed in its use by a qualified person.
8
DO NOT drop, throw or abuse the drill.
8
DO NOT carry the drill by the air hose, or yank the hose from the air supply.
8
DO NOT operate drill if you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT carry drill with your hand on the power trigger in order to avoid unintentional starting.
8
DO NOT direct air from the air hose at yourself or others.
8
DO NOT wear loose jewellery and tie back long hair.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. INTRODUCTION
Textured finish to ensure a good grip. mini design for working in confined areas, ideal for working around engines where space is limited. Powerful
mini drill 6000rpm, Ø6mm key chuck 1-6mm drill bits. Safety trigger prevents inadvertent operation. Suitable for professional workshop use.
Supplied with chuck key.
3. sPECIFICATION
model no: .................................................................. SA1007
Chuck Size: ................................................................. Ø6mm
Free Speed: ............................................................. 6000rpm
Air Consumption:......................................................... 8.5cfm
operating Pressure: ...................................................... 80psi
Inlet Size: ..................................................................1/4"BSP
noise Power/Pressure: ...................................... 101/90dB(A)
Vibration/Uncertainty: ............................ 0.461m/s²/0.541m/s²
4. PREPARATION
4.1. AIR sUPPLY
WARNING! ensure the air supply is clean and does not exceed 80psi while operating the drill. Too high an air pressure and unclean air
‰
will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.1. ensure drill air valve (or trigger) is in the "off" position before connecting to the air supply.
4.1.2. You will require an air pressure of 80psi, and an air flow according to specification.
4.1.3. drain the air tank daily. Water in the air line will damage the drill.
4.1.4. Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig 1.
© Jack Sealey limited
MINI AIR DRILL Ø6MM 6000RPM KEY CHUCK
sA1007
model no:
Wear eye Wear face
protection mask
Original Language Version
Wear ear
protection
SA1007 Issue 2 (3) 19/12/19