Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Service Hints How to remove the backcover Lay the main unit face down. (see Fig.5) Fig.5 How to remove the Pedestal assembly Remove the 4 fixing screws and the pedestal assembly. (see Fig.6) SCREWS XYN4+F12FJK (4pcs) Fig.6 Remove the 15 fixing screws and the backcover. (see Fig.7) SCREWS XTV3+12JFJ (19pcs)
Chassis Board Layout GK-BOARD P-BOARD A-BOARD KA-BOARD Board Name Function AV Terminal, HDMI, Digital Audio Out,Tv tuner, SD Card A-Board CI slot, sLD2, AV switch, Speaker Out, EEPROM FlashMemory, DDR SDRAM P-Board Power Supply, Main Input, Inverter KA-Board Remote Receiver, R/G LED GK-Board Control Button, Power Switch Location of Lead Wiring...
How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press [STATUS] button on the remote control for more than 3 seconds. TV will be forced to the factory shipment setting after this SELF CHECK. Model and Keys: Keys Model No. One-to-one CI PLUS DTCP-IP (for USB Rec.) TX-L32C4E NONE NONE...
Setting Inspection Voltage Confirmation A board Description Test point Voltage SUB3.3V TP8701 3.21V - 3.45V SUB1.5 V TP8101 1.47V - 1.56V SUB1.2V TP8100 1.07V – 1.21V SUB5V TP0910 4.8V – 5.2V P board Description Test point *Voltage **Voltage DTV16V TP7505/7801 15.6V ±...
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button. Panasonic 2011LCD 32HD TX-L32C4E Self Check Complete...
Power LED blinking timing chart Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit. Blinking Blinking timing Contents...
Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu How to enter SERVICE While pressing (-/v) button on TV unit, press on the remote control for 3 times within 2 seconds.
SERVICE SERVICE Peaks SOFT 1.901 OPTION 1 Key Command ADJUST Peaks EEP 01.00.0001 OPTION 2 WB-ADJ LSI PACKAGE 1.721 OPTION 3 OPTION LSI DATA 1.00.00 OPTION 4 SRV-TOOL STBY SOFT 2.00.00 Model ID Press the 3/4 button to change the adjustment values or function. STBY EEP 2.01.0000 034e6100...
Service Tool Mode How to access Select [SRV-TOOL] in Service Mode. Press [OK] button on the remote control. SRV-TOOL Display of TD2Microcode version TD2Microcode:005a0910 Flash ROOM: AD – F1 Display of Flash ROM maker code POWER ON TIME/COUNT PTCT:00.00.00.00.00 Time 00051:30 On/Off 0000042 Display of SOS History Press [MUTE] button (3sec)
Hotel Mode 1. Purpose Restrict a function for hotels. 2. Access command to the Hotel mode setup menu. In order to display the Hotel mode setup menu, please enter the following command (within 2 second). [TV] : Vol.[Down] + [REMOTE] : AV (3 times) Then, the Hotel mode setup menu is displayed.
Data Copy by SD Card Purpose a) Board replacement (Copy the data when exchanging A-board): When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board. Following data can be copied. (Before exchanging) User setting data Copy to SD card...
Data Copy from TV set to SD Card Turn on the TV set. Insert SD card with a startup file (pwd.file) to SD slot. On-screen Display will be appeared according to the startup file automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2770 (b) For Hotel: 4850 Data will be copied from TV set to SD card.
Data Copy from SD Card to TV set Turn on the TV set. Insert Sd card with Data to SD slot. On-screen Display will be appeared according to the Data folder automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2771 (b) For Hotel: 4851 Data will be copied from SD card to TV set.
Option Bytes Description OPTION1 TEXT Ch Refresh ON (1) / OFF (0) ID-1 ON (1) / OFF (0) Macrovision Auto-judge ON (1) / OFF (0) Surround enable low bit ON (1) / OFF (0) Surround enable high bit ON (1) / OFF (0) TINT_Component_HDMI ON (1) / OFF (0) OPTION2...
Adjustment Method Sub-Contrast/White Balance Adjustment Instrument Name Connect to Remarks Remote controller Correlation can be also taken by LCD WB meter (Minolta CS-1000A equivalent) CA-210 or equivalent Comunication jig Computer for external control Procedure Remarks Let the panel standfor more than 3 hours at more than 20 C.
Replacement Parts List Important Safety Notice Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order. RTL (Retention Time Limited) Note: The marking (RTL) indicates that the Retention Time is Limited for this item.
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM () (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.