LG DLE7000 Series Service Manual
Electric & gas dryer
Hide thumbs
Also See for DLE7000 Series:
- Owner's manual (144 pages) ,
- Owner's manual (92 pages) ,
- Owner's manual (92 pages)
Table of Contents
Advertisement
SEC.
WORK
BRAND
45
LG
2
1
분해도 페이지 표기 및 숫자 이미지로 수정
EAGL600213
REV. NO.
REVISION DESCRIPTION
REF. NO.
PRINTING DEGREE
MODEL
EXTERIER INTERIER
DLE7000*
MFL69290445
1
21/06/09
안 영 민
김 재 석
DATE
PREPARED
APPROVED
MATERIAL AND PRINTING DESCRIPTION
1
TRIG.
MODELING
DESIGNED
REVIEWED
안 영 민
21.05.24
LG Electronics Inc.
LANGUAGE
PAGE
REMARK
EUS
48
SCALE 1
MANUAL,Service
UNIT
mm
1
T
CHECKED APPROVED
I
T
안 영 민
김 재 석
L
21.05.24
21.05.24
E
MFL69290445
RELATED DWG.
DWG.
No.
RELEASING THIS DRAWING
WITHOUT PERMISSION LG
Electronics SHOULD BE
ACCUSED ACCORDING TO THE
LAWS AND COMPANY RULES.
DR COMPLETED
PDF
ILLUSTRATOR
1/1
Advertisement
Table of Contents
Related Manuals for LG DLE7000 Series
Summary of Contents for LG DLE7000 Series
- Page 1 RELEASING THIS DRAWING WITHOUT PERMISSION LG Electronics SHOULD BE ACCUSED ACCORDING TO THE LAWS AND COMPANY RULES. SEC. PRINTING DEGREE MATERIAL AND PRINTING DESCRIPTION LANGUAGE PAGE REMARK WORK BRAND MODEL EXTERIER INTERIER DLE7000* MFL69290445 DR COMPLETED ILLUSTRATOR SCALE 1 MANUAL,Service TRIG.
- Page 2 Any reproduction, duplication, distribution (including by way of email, facsimile or other electronic means), you have obtained the prior written consent of the LG Electronics entity from which you received this Service Manual. The material covered by this prohibition includes, without limitation, any text, graphics or logos in this Service Manual.
-
Page 4: Table Of Contents
13-2-2. CABINET AND DOOR ASSEMBLY : GAS TYPE ............45 13-3-1. DRUM AND MOTOR ASSEMBLY : ELECTRIC TYPE ..........46 13-3-2. DRUM AND MOTOR ASSEMBLY : GAS TYPE ............47 Copyright © 2016 - 2017 LG Electronics Inc. All rights reserved. Only training and service purposes. -
Page 5: Spectifications
114.9 lb (Elec) 118.6 lb (Gas) ACCESSORIES Optional accessory Dryer rack (1 each) See page 6 of this manual for usage instruction. - Page 6 DLE7100* DLG7101* DLE7000* DLG7001* Control Lock...
- Page 8 3-1 Connecting Electric Dryers 4-wire direct If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker 3-wire direct 5" (12.7 cm) If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker...
- Page 10 3-2 Connecting the gas supply...
-
Page 11: Dryer Cycle Process
Normal Dry Perm. Press 32min Normal Dry Elec : 67 Normal Medium Gas : 63 Normal Dry Delicates 28min Normal Dry 55min Medium Bedding Normal Dry High Heavy Duty 54min High Speed Dry Adjustable Adjustable Air Dry No Heat Adjustable FRESEEN UP Medium The Energy Saver option is turned on by default in the Cotton/Normal cycle. -
Page 12: Component Testing Informaiton
Auto reset -31°F (-35°C) Same shape as outlet thermostat. Measure resistance of the following terminal 1) Door open Terminal: COM - NC (1-3) Terminal: COM - NO (1-2) 2) Door closed Terminal: COM - NC (1-3) Terminal: COM - NO (1-2) - Page 14 Ω Ω...
-
Page 15: Motor Diagram And Schematic
When checking Component, be sure to turn Power off, then do voltage discharge sufficiently. Ω Ω Ω Ω... -
Page 16: Wiring Diagram
(ELECTRIC DRYER) MEZ67011402... - Page 17 (GAS DRYER) MEZ67011403 (ELECTRIC DRYER) MEZ67011402...
- Page 19 Installation Test (Duct Check) Check the display for results. During the test cycle, monitor the Flow Sense™ Once you have completed the installation of the display on the control panel. If the Flow Sense™ dryer, use this test to make sure the condition of the LED is not turned on, when the cycle ends, exhaust system is adequate for proper operation of the exhaust system is adequate.
- Page 20 Troubleshooting for flow sensor dryer • Check the Error Code before you call for service Error Code Possible Causes Solutions or tE2 • Temperature sensor failure • • Humidity Sensor failure. • • Electric dryer power cord is not • Check the power supply or the connection of connected correctly, or house power power cord to the terminal block.
-
Page 22: Test 1 120 Vac Electrical Supply
120V AC Electrical Supply... - Page 24 ✽...
-
Page 25: Test 2 Thermostor Test - Measure With Power Off
Thermistor Test --- Measur e with Power Off... -
Page 26: Test 3 Motor Test
Motor Test Drum does not rotate, fan does not turn, heater does not function. Ω Ω Ω Ω page 12 Ω page 15... -
Page 27: Test 4 Moisture Sensor
Moistur e Sensor Moistur e sensor Ω... -
Page 28: Test 5 Door Switch Test
Door Switch Test half- Ω Ω Ω Ω... -
Page 29: Test 6 Heater Switch Test - Electric Type
Heater Switch Test - Electric Type Ω Ω Ω Ω Ω Ω... -
Page 30: Test 7 Gas Valve Test - Gas Type
GAS Valve Test - Gas Type GAS V alve test - Gas T ype Ω... -
Page 31: Change Gas Setting (Natural Gas, Propane Gas)
CHANGE GAS SETTING (NATURAL GAS, PROPANE GAS) Changing orifices and gas valve adjustments improperly can result in an Warning explosion and/or fire. Conversion must be made by a qualified technician. Initially, The burner is set for natural gas at the factory. The propane orifice conversion kit is sold as a service part to authorized servicers only. -
Page 33: Disassembly Instructions
PANEL REAR [ELECTRIC] 1. Remove 1 screw. 2. Pull out the cover. 3. Remove 3 screws. 4. Disassemble terminal block and wire from panel rear. PANEL REAR [ELECTRIC] 1. Remove one screw for removing safety cover. 2. Remove 5 screws remained on the panel rear. - Page 34 CONTROL PANEL ASSEMBLY 1. Place a towel over the top cover to prevent scratching the surface. Gently lift each corner of the back panel, then roll it forward so it rests on top of the dryer. 2. Disconnect the wiring from the PWB (PCB) board.
- Page 35 CONTROL PANEL 1. The knob can be taken out if pulled forward. 2. Remove 5 screws from control panel assembly. 3. Separate PCB from control panel.
- Page 36 How to change top cover 1. Remove the 5 screws. 2. Disassemble terminal block with power cord. 3. Disassemble rear panel and both side screws.
- Page 37 4. Disassemble front panel. Be careful to avoid breaking the plastic hook (shown) when removing the front panel. 5. Disassemble PCB and housing from the PCB. 6. Push the 2 spring clamps by using a putty knife between top cover and door cabinet. 7.
- Page 39 FRAME ASSEMBLY (FRONT BULKHEAD) connector frame assembly (front bulkhead). frame assembly (front bulkhead).
- Page 40 ※ All necessary vent conversion parts are included in the dryer vent kit, part number 3911EZ9131X Place the shorter duct section into the dryer. Install a screw through the holding tab to the bracket in the base of the dryer. Attach the 4-inch elbow to the remaining 4-inch duct.
- Page 41 It is not necessary to remove the electrodes or the grid to change or replace the filter. frame assembly (front bulkhead). ※ This is a left-hand thread. frame assembly (front bulkhead). 7 screws from the back of the dryer. Remove the rear tub drum by taking it out through the inside of the dryer cabinet.
- Page 42 frame assembly (front bulkhead.) frame assembly (front bulkhead.) frame assembly (front bulkhead.)
-
Page 43: Fastener Chart - Size And Positions
FASTENER CHART - SIZES and POSITIONS Reversing the Door WARNING 4. Remove the 4 screws securing the hinges to the door frame. Remove the two plastic cover caps. Reinstall THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure the hinges and cover caps on the opposite sides from to follow the instructions below can result in damage to which they were removed. -
Page 44: Exploded View
EXPLODED VIEW Control Panel and Plate Assembly A130 A141 A140 A110 A143 A120 A210 A211 A570 A215... -
Page 45: Cabinet And Door Assembly : Electric Type
A700 A800 A212 A610 A212 A600 A320 A315 A330 A311 A500 A325 A510 A313 A314 A131 A310 A430 A545 A520 A540 A440 A420 A450 A430 A400... -
Page 46: Cabinet And Door Assembly : Gas Type
13-2-2. A700 A800 A212 A212 A600 A320 A550 A315 A330 A311 A500 A325 A510 A313 A314 A131 A310 A430 A545 A520 A540 A440 A420 A450 A430 A400... -
Page 47: Drum And Motor Assembly : Electric Type
K400 F200 K120 K145 K100 K140 K230 K130 K252 K251 K250 K336 K210 K350 K320 K335 K310 K330 K250 K620 K550 K560 K610 K251 K252 K540 K240 K530 K515 K520 K510 F140 K655 K640 K660 F130 K650 F110 K651 K600 F120... -
Page 48: Drum And Motor Assembly : Gas Type
13-3-2. K400 F200 K120 K142 K100 K140 K230 K130 K252 K251 K250 K336 K210 K350 K320 K335 K310 K330 K620 K250 K550 K560 K610 K251 K252 K540 K240 K530 K520 K510 K660 K651 K655 K640 M141 M240 M150 M220 K515 M160 K650 M171... - Page 49 DEC, 2020 PRINTED IN KOREA MFL69290445...