↓ ↓ ↓ ↓ 2. Press button again and hold button down. ↓ ↓ ↓ ↓ Service Mode display 3. While holding the button, press MENU button on TV set. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 3
Key Function in the Service Mode The following key entry during display of adjustment menu provides special functions. CAUTION: Never try to perform initialization unless you have changed the memory IC. button (on remote control) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
ADJUSTING ITEMS AND DATA IN THE SERVICE MODE: Note: The image system data of RCUT-BDRV is different by each image format. The PAL value is indicated in the table. Never adjust H.POS and V.POS except PAL/WIDE mode. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 5
TV SET OPTION 7 (HOTEL MODE) OPT8 TV SET OPTION 8 (HOTEL MODE) TVOP TV SET OPTION MODEL ID BDWID BORDER WIDTH FOR EXACT SCAN BDHIT BORDER HEIGHT FOR EXACT SCAN FPLG MASK_ENABLE (SD/HD) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
After selecting TVOP, press + or - to set I2C check function to disable or enable as below. TVOP FUNCTION DESCRIPTION 0 (Normal) D5 (bit5) I2C check between IC700 and IC400. (WDT) Disable Enable file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 8
Ex. OPT5 value 0x05 indicates that panel size is 32. OPT5 (bit7) (bit6) (bit5) (bit4) (bit3) (bit2) (bit1) (bit0) Size Convert from Bit (Binary) to Hex The table for converting from bit (D7-D0) to hex (0x**). BIT (Binary) High nibble Low nibble file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 9
6) Progress status is changed "OK" and power cycle (automatically). Then QA02 initialization has been completed. 7) Enter the service mode and select version check mode. Confirm if model name and model id set is correct. If not, repeat steps 1) to 6). file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 11
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 10 из 21 0x26 0x27 0x28 0x29 0x30 0x31 0x32 0x33 Initializing Data setting flowchart after replacing the Signal Unit file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 12
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 11 из 21 Test Signal Selection file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
The diagnosis will begin to check if interface among IC's is executed properly. 2. During diagnosis, the following displays are shown. * Self check display and Item are subject to the models. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 14
When the abnormal status is detected, type name of semiconductor is indicated in red colour. (6) Block : TV reception mode V1 - V9 : VIDEO 1-9 input mode : PC mode : YUV mode : DTV mode (SCART (FULL)) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 15
1. Press "9" button twice on remote control during display of adjustment menu in the service mode. The version of main MPU will be checked. 2. During Version Check, the following displays are shown. * Version check display and Item are subject to the models. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 16
(5) HDMI ID : HDMI ID information : Display 4 byte data. (6) SW Ver Version information of DB software as Toshiba release. (Only digital model.) (7) MW Ver Left side is Application and UI version information of DB software. (Only digital model.)
Page 17
1. Press "9" button thrice on remote control during display of adjustment menu in the service mode. The status of this model will be checked. 2. During Status Check, the following displays are shown. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Sub PLL information : Display 1 byte data at five. This item displays only Double window model. (7) SCREEN SIZE : Display the screen size as follows. Exact Scan Wide Super Live 2 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
All keys except input selector key Disable Enable (Video/TV) D3 (bit3) User remote control operation Disable Enable (Service mode and Supere User mode may possible to setting only) D2 (bit2) Disable SET UP MENU except Disable Enable file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 20
0 (Normal) D7 (bit7) Enable mode that speaker volume will be set Enable Disable in forced when turn ON the main power D6 (bit6) ~ Forced speaker volume 0 ~ 100 [decimal] (Normal: 0) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
2 Green is OFF; Abnormal operation of Turn OFF the TV and unplug Red blinks continuously at 1- BUS line. the power cord. second intervals. Plug the power cord in again and turn ON the TV. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 22
ADJUSTMENT [LCD Color Television] ASIA_EU Стр. 21 из 21 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Стр. 1 из 1 FUNCTION AND OPERATION The Remote Control Simple at-a-glance reference of your remote control. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
A wide variety of external equipment can be connected to the input sockets on the side of the television. Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the television may be used for some functions. Switching On file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 25
Стр. 2 из 2 Using the Controls and Connections file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 26
Tuning the Television Using Quick Setup, Sorting Programme Positions Before switching on the television put your decoder and media recorder to Standby if they are connected. To set up the television use the buttons on the remote control. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 27
Стр. 2 из 3 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 28
Стр. 3 из 3 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
To allocate a programme position on the television for a decoder and media recorder: turn the decoder on, insert a pre-recorded film in the media recorder and press PLAY, then manually tune. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 30
Стр. 2 из 4 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 31
Стр. 3 из 4 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 32
Стр. 4 из 4 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 33
Стр. 1 из 2 FUNCTION AND OPERATION Auto Tune Using Auto Tuning file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 34
Стр. 2 из 2 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
LCD cover and fasten with screws. Do not strongly push on the module because any impact can adversely affect the performance. Also use caution when handling the polarized screen because it can easily be damaged. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 36
Immediately remove any type of fluid from the screen. 5. Glass is used in the panel, so do not drop or strike with hard objects. Such actions can damage the panel. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 37
Failure to do so could result in freezing of the liquid crystal due to cold air or loss of resilience or other damage. 9. Do not disassemble the LCD module. Such actions could result in improper operation. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 38
Стр. 4 из 4 10. When transporting the LCD module, do not use packing containing epoxy resin (amine) or silicon resin (alcohol or oxim). The gas generated by these materials can cause loss of polarity. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
6. Always use the replacement parts specified for the particular model when making repairs. The parts used in products require special safety characteristics such as file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 43
Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground such as a water pipe. Annex D (normative) Measuring network for TOUCH CURRENTS file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 44
- for d.c. : = 1.0 V Note: The limit values of = 0.35 V (peak) for a.c. and = 1.0 V for d.c. correspond to the values 0.7 mA (peak) a.c. and 2.0 mA d.c. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts which do not have the same safety characteristics as specified in the parts list may create electrical shock, fire, or other hazards. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Стр. 1 из 2 SPECIFICATION file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 47
Стр. 2 из 2 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 55
Digital BOARD P212B (A3030D ONLY) Audio OUT CVBS CVBS OUT PJ212 IC302 Serial port Audio Amp for debug ITU-R656 P200B H801 Digital VIDEO OUT +Low B PJ400 AC INPUT& IC301 Tuner UART DVB-CI×1 IC801 POWER BOARD POWER BOARD IF Amp Audio DAC COFDM Demod IC401...
Unless otherwise noted in schematic, all capacitor values less than 1 are expressed in F, and the values more than 1 in pF. All capacitors are ceramic 50 V, unless otherwise noted as the following marks. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 57
AC volts. 5. Waveforms are taken receiving color bar signal with enough sensitivity. 6. Voltage reading shown are nominal values and may vary ±20 % except H.V. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 117
Стр. 1 из 2 CABINET Stand Exploded View A425 A426 A427 A428 A429 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 118
Стр. 2 из 2 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 119
23357900 DIODE, ZENER, MTZJ33B U01A POWER (PE0300) D815 23357892 DIODE, ZENER, MTZJ27B U01A POWER (PE0300) D817 23357512 DIODE, AL01Z U01A POWER (PE0300) D852 23357697 DIODE, 1SS133 U01A POWER (PE0300) D883 23362113 DIODE, FML-G22S file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 120
IC, PHOTO COUPLER, TLP421F(GR) U01A POWER (PE0300) QE83 23085587 IC, TA76431S U01A POWER (PE0300) R801 76004716 RESISTOR, METAL GLAZE, 1/2W 2.2M OHM J U01A POWER (PE0300) R805 76554683 RESISTOR, OXIDE METAL FILM, 2W 68K OHM J file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 121
U02A LOW_B (PE0253) CE150 76092179 CAPACITOR, CERAMIC CHIP, 25V B 0.22UF K U02A LOW_B (PE0253) CE151 76092179 CAPACITOR, CERAMIC CHIP, 25V B 0.22UF K U02A LOW_B (PE0253) CE200 76073183 CAPACITOR, ELECTROLYTIC, 35V 220UF M file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 134
U04AS MAIN (PE0288) IC420 V47GD0001110 STEP-DOWN CONVERTER U04AS MAIN (PE0288) IC422 75006027 IC II2C SWITCH U04AS MAIN (PE0288) IC501 75006034 U04AS MAIN (PE0288) IC511 V47GD0000897 SYSTEM RESET IC U04AS MAIN (PE0288) IC512 75001878 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 135
U04AS MAIN (PE0288) N007 23961272 M705ESC 1.2 U04AS MAIN (PE0288) N008 23962411 AD EP 3609 U04AS MAIN (PE0288) N009 23964124 SOL #4520 UN U04AS MAIN (PE0288) P101A KETSU U04AS MAIN (PE0288) P200A 23713940 B-PH-K-S(LF) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 136
U04AS MAIN (PE0288) Q365 75002029 TRANSISTOR U04AS MAIN (PE0288) Q409 V41GD0000236 NPN TRANSISTOR U04AS MAIN (PE0288) Q464 V41GD0000236 NPN TRANSISTOR U04AS MAIN (PE0288) Q465 V41GD0000236 NPN TRANSISTOR U04AS MAIN (PE0288) Q466 V41GD0000236 NPN TRANSISTOR file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 137
V01GD0001693 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R2015 V01GD0001693 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R2016 V01GD0001693 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R2017 V01GD0001693 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R2018 V01GD0001750 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 138
CHIP RESISTOR (1005) U04AS MAIN (PE0288) R2222 75007598 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R2223 75007598 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R2225 V01GD0002077 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R2226 V01GD0002077 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 139
V01GD0001733 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R3120 V01GD0001750 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R3130 V01GD0001702 CHIP JUMPER 1608TYPE U04AS MAIN (PE0288) R3131 V01GD0001702 CHIP JUMPER 1608TYPE U04AS MAIN (PE0288) R3132 V01GD0001702 CHIP JUMPER 1608TYPE file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 140
CHIP RESISTOR (1005) U04AS MAIN (PE0288) R4008 V01GD0001732 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R4009 V01GD0001732 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R401 75005985 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R4010 V01GD0001732 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 141
V01GD0001736 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R438 V01GD0001736 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R439 V01GD0001736 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R440 V01GD0001736 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R4400 V01GD0001732 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 142
V01GD0001732 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R5023 V01GD0001732 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R5024 V01GD0001732 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R5025 V01GD0001739 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R5026 V01GD0001732 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 143
V01GD0001692 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R5942 V01GD0001692 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R5943 V01GD0001692 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R5956 V01GD0001692 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R5957 V01GD0001692 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 144
V01GD0001695 CHIP JUMPER 1005TYPE U04AS MAIN (PE0288) R6302 75007599 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R6304 75007600 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R6305 V01GD0001732 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R6306 V01GD0001758 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 145
V01GD0002061 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R6805 V01GD0001758 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R6806 V01GD0002061 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R6807 V01GD0001758 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R6808 V01GD0002061 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 146
CHIP RESISTOR (1005) U04AS MAIN (PE0288) R810 V01GD0001292 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R811 75007597 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R812 V01GD0001692 CHIP RESISTOR (1005) U04AS MAIN (PE0288) R813 V01GD0001750 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 147
VARISTOR CHIP V1=40V U04AS MAIN (PE0288) V2403 75006015 VARISTOR CHIP V1=40V U04AS MAIN (PE0288) V2601 75006015 VARISTOR CHIP V1=40V U04AS MAIN (PE0288) V2602 75006015 VARISTOR CHIP V1=40V U04AS MAIN (PE0288) V5009 75006015 VARISTOR CHIP V1=40V file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 148
V01GD0001702 CHIP JUMPER 1608TYPE U04AS MAIN (PE0288) W9102 V01GD0001279 CHIP RESISTOR (1005) U04AS MAIN (PE0288) W9103 V01GD0001279 CHIP RESISTOR (1005) U04AS MAIN (PE0288) W9104 V01GD0001279 CHIP RESISTOR (1005) U04AS MAIN (PE0288) W9105 V01GD0001279 CHIP RESISTOR (1005) file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 149
MANUAL NORDIC MANUAL, NORDIC MANUAL Accessory Y102E 75007728 MANUAL E EURO MANUAL, E EURO MANUAL Accessory Y110 75007724 MANUAL QSUG A3000P, QSUG Accessory Y114 75007725 MANUAL ITALIAN SCHEMATIC, ITALIAN SCHEMATIC Accessory Y130 75001967 REMOCON HAND UNIT, CT-865 file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 150
A429 75007716 TOOL, ALLEN KEY Cabinet A430 75005733 PIECE CLAMP HOLDER Packing A701 75007717 CARTON CASE, CASE Packing A702A 75007718 PAD TOP PACKING, TOP PACKING Packing A702B 75007719 PAD BOTTOM PACKING, BOTTOM PACKING file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Abbreviations Capacitors CD : Ceramic Disk Resistors : Carbon film OMF : Oxide Metal Film : Plastic Film : Carbon Composition : Variable Resistor : Electrolytic file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...
Page 152
Стр. 2 из 2 : Metal Film : Fusible Resistor All CD and PF capacitors are ±5 %, 50 V and all resistor, ±5 %, 1/6 W unless otherwise noted. file://D:\Documents and Settings\Admin\Рабочий стол\26A3000P Ver. 2.00\TOSHIB... 20.07.2015...