Advertisement
Reception
I
n s t a l l a t i o n
• Shares frequency with
o f A c c e s s o r i e s
several different types of
Installing Spring-Type Belt Clip
devices — interference may
be experienced
• Position clip, spring pointing up,
to backside of handset
• Radio interference may cause
interruption to conversation
• Align four prongs on clip to four
• Moving handset while talking
slots on handset
or relocating base unit may
• Gently press clip to snap prongs
improve reception
into place
Note:
Installing Headset
If reception is lost completely dur-
• Pull back rubber cover from
ing conversation mode,
side of headset to expose
replace handset on base unit to
connection port
resynchronize range; call is lost.
• Insert 2.5mm connector of
headset jack
Out of Range
• Replace rubber cover after use
• Communication is halted for 30
to ensure port cleanliness
seconds during conversation
Notes:
• Handset will automatically search
for and select a clear channel
1.When headset is plugged in,
• If none is found, an error tone
handset speech path becomes
will ring on handset when not on
disabled.
base station
2. Rubber cover need not be
Manual Channel Selection
completely removed to use port.
If reception becomes garbled or
static occurs, channels can also be
manually changed.
O
p e r a t i o n
• Press ["CH"] key during conver-
sation to activate 3-channel
All operational instructions assume
semi-auto scan (MCA)
that these features are assigned to
• While channel is changing, low
the DTP-16HC-1 Terminal: Prime
battery LED will blink
Line Pickup to your Primary
Extension and Ringing Line.
• If channel not found, error
tone will sound and channel
Receiving Calls
will not change
When receiving a call, handset rings
and Message Waiting LED blinks
rapidly in conjunction with base
station LED.When handset is on
base station, only the base station
rings and Message Waiting LED
blinks rapidly.When handset is in
standby mode, both handset and
All manuals and user guides at all-guides.com
base station ring and Message
Waiting LED blinks rapidly in
conjunction with base station LED.
Note:
When [Ringer "ON/OFF"] switch is
in "Off" mode, handset will not
ring, but Message Waiting LED
flashes.
Auto Talk Feature Switching
To change mode, press and hold
["TRF"] key while moving [Ringer
"ON/OFF"] Switch from "Off" to
"On. " When mode is changed, confir-
mation tone sounds: Auto Talk Off
produces 3 beeps; Auto Talk On
produces 2 beeps.
Note:
This feature only applies if tele-
phone type allows for Prime Line
selection when going off-hook on
that station.
Answering Calls with
Auto Talk Off
• Lift handset from base unit
• Press any key
• Begin conversation
• At end of conversation, return
handset to base station or press
["TALK"] key
• Call is disconnected
Answering Calls with
Auto Talk On
• Lift handset from base unit
• Begin conversation
• At end of conversation, return
handset to base station or press
["TALK"] key
• Call is disconnected
Notes:
1. ["TALK/BATTERY LOW"] LED
flashes then remains lit as
communication path is
established between handset
and base station.
2.The Auto Standby feature
(no need to press ["TALK"] key
to disconnect call) only applies
when returning handset to
base station.
3.While in talk mode, Message
Waiting LED is inactive; when
call is disconnected, Message
Waiting LED is reactivated and
flashes if messages are waiting.
Making Calls with Auto Talk Off
• Lift handset from base unit
• Press any key
• Listen for dial tone and dial
number
• Begin conversation
• At end of conversation, return
handset to base station or press
["TALK"] key
• Call is disconnected
Making Calls with Auto Talk On
• Lift handset from base unit
• Listen for dial tone and dial
number
• Begin conversation
• At end of conversation, return
handset to base station or press
["TALK"] key
• Call is disconnected
Notes:
1. ["TALK/BATTERY LOW"] LED
flashes then remains lit as
communication path is estab-
lished between handset and base
station, and dial tone is heard.
The communication time out is
5 seconds. If communications
path cannot be established
Placing Calls on Hold with
within 5 seconds, error tone
call in progress from the
will sound and handset reverts
base station:
to standby mode.
• Press ["HOLD"] key or ["TA
key
2.Applies ONLY when connected
to an NEC Electra Elite
®
2 — In
• Return handset to base stati
conversation mode, handset will
• Press flashing ["LINE"] key
no longer produce DTMF, but the
continue call
base station will produce DTMF.
• Press ["TALK"] or pick up
handset
With a call in progress from
F
e a t u r e s a n d
handset (PBX):
S e t t i n g s
• Press ["TRF"]
Setting Handset Ringer On/Off
• Listen for stutter tone
When handset is in standby mode,
• Press ["TRF"] to continue c
ringer volume can be adjusted Low
With a call in progress from
or High by pressing ["VOL"] key.
handset (Key System):
Ringer volume can be adjusted even
• Press ["TRF"] key or ["TALK
when [Ringer "ON/OFF"] switch is
in "Off" position.
• Return handset to base stati
Adjusting Handset/Headset
• Press flashing ["LINE"] key
Reception Volume
continue call
When call is in progress, press
• Press ["TALK"] or pick up
["VOL"] key repeatedly to increase
handset
handset/headset speaker volume
Note: After a preprogrammed
from NORMAL to MEDIUM to
any held call will recall to the
HIGH to LOW — in this order.
inating terminal.
After disconnect, volume reverts
to NORMAL setting.
Conference Calling with a c
in progress:
Muting Handset/Headset
Volume
• For Electra Elite/Electra
Professional — Press ["CON
When call is in progress, press
key on base station
["MUTE"] key to disable micro-
phone.The ["TALK/BATTERY LOW"]
• For NEAX
LED flashes when handset/headset
["TRF"]
is muted.Voice is not transmitted in
• Place second call (internal o
MUTE mode. Press ["MUTE"] key
external)
again to reactivate microphone.
• Announce conference (opti
Note:
• Press ["CONF"] from base s
Handset/headset volume control
to establish conference
is compatible with new HAC
regulations.
®
2400/2000 — Pr
Advertisement
