EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPOR- TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, SAFETY-RELATED COMPONENT WARNING !! NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT COMPONENTS IDENTIFIED BY SHADING AND MARKED MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.
Page 3
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
Page 4
y l l . s l . s l . s l . s l e i l & n i l i n i WARNING (UK Models only) The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 5 AMP rating.
Page 5
21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio output B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left) Output impedence : Less than 1kohm*...
Page 6
FE-2D SELF DIAGNOSTIC SOFTWARE The identification of errors within the FE-2D chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal => => => Remove the rear cover fixing screws indicated and withdraw the rear cover from the Beznet. 2-2. Chassis Removal and Refitting When refitting the chassis ensure that the main bracket is located in the beznet guide slots before sliding the chassis forwards.
2-3. A Board Removal [ Step 1 ] 2-4. A Board Removal [ Step 2 ] Clip. Screw. Remove the 3 screws securing the PWB to the main bracket. Release the 5 securing clips located around the side of the 1 can be seen in the photo above and the other 2 are either chassis and slide the PWB clear of the bracket.
2-6. A1 Board Removal 2-7. Service Position Clip. Release the 4 securing clips located around the side of the Position the chassis as indicated to access the solder side chassis and slide the PWB clear of the bracket. of the PWB’s. To gain access to the A Board follow the instructions on page 16.
2-9. Picture Tube Removal WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.
SECTION 3 SET-UP ADJUSTMENTS • Carry out the adjustments in the following order : When complete readjustment is necessary or a new picture 3-1. Beam Landing. tube is installed, carry out the following adjustments. 3-2. Convergence. • Unless there are specific instructions to the contrary, carry 3-3.
If the V.STAT magnet is moved in the direction of the (a) 3-2. Convergence and (b) arrows, the Red, Green and Blue points move as indicated below. Preparation: • Before starting this adjustment, adjust the focus, horizontal size and vertical size. •...
Page 19
Geometry Adjustment. YCH Adjustment Preparation: YCH VR 28" YCH VR 32" Before starting this adjustment, adjust the horizontal and vertical static convergence. Deflection Yoke Deflection Yoke Remove the deflection yoke spacer. Tilt the deflection yoke as indicated in the figure below and TLV Adjustment optimise the geometry.
Layout of each control 3-4. Screen (G2), White Balance [Adjustment in the service mode using the remote commander] G2 adjustment Input a dot signal from the pattern generator. Set the Picture, Brightness and Colour to minimum. Apply 165V DC from an external power supply to the R, G V.STAT and B cathodes of the CRT.
SECTION 4 CIRCUIT ADJUSTMENTS 4-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied remote Commander RM-949. How to enter into the Service Mode Turn on the main power switch and enter into the stand-by mode. Press the following sequence of buttons on the Remote Commander.
Page 22
Deflection System Adjustment Sub Brightness Adjustment Set the TV set or operation in Service Mode [ See Page 21 ] Input a Monoscope pattern. and enter into the ‘Geometry’ service menu. Set the TV set or operation in Service Mode. [ See Page 21 ]. Select and adjust each item in order to obtain the optimum image.
4-2. TEST MODE 2: Test Mode 2 is available by programming the TV set for operation in Service Mode [ As shown on Page 21 ], OSD ‘TT’ appears. The functions described below are available by selecting the two numbers. To release the ‘Test mode 2’, press 00, 10, 20 ... twice or switch the TV set into Stand-by mode.
5-1. BLOCK DIAGRAMS (1) T3602 T3601 LIGHTNING LINE FILTER LINE FILTER FUSE CN3601 CN3603 F3601 AC IN AC OUT H9 BOARD AC IN AC OUT CN7602 F3 ( CN4101 AC INPUT, FUSE RIGHT LEFT TUNER MUTE SDA (TV) TU4102 SWITCH FBLK Q4106 CVBS...
5-1. BLOCK DIAGRAMS (3) IC501 PH601 VERTICAL DEFLECTION ISOLATOR BOOSTER CN606 CN501 LOW B AC IN V- DY+ BOOST MAIN RECT H9 BOARD V- DY- AC IN RELAY D601 CN7601 RY601 H- DY- TO DY CN603 H- DY- DGC CHECK H- DY+ FOR CHECK D614...
5-2. CIRCUIT BOARD LOCATION Reference Information RESISTOR : METAL FILM : SOLID C Board FPRD : NON FLAMMABLE CARBON FUSE : NON FLAMMABLE FUSIBLE : NON FLAMMABLE METAL OXIDE VM Board : NON FLAMMABLE CEMENT B1 Board : NON FLAMMABLE WIREWOUND CVM Board N Board S1 Board...
Page 29
~ A Board Semiconductor Location Table ~ NOTE: ~ A Printed Wiring Board ~ Portions of the circuit marked as shown are high voltage areas. Use care to prevent electric shock during inspection or repair. - 29 -...
Page 33
TO H9 BOARD CN908 A..-28DL11 CN1201 CN1200 CN1202 J1200 IC1201 C1225 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL TDA7495S AUDIO AMP R1202 R1217 JW1232 XX JW1227XX 1/10W JW1209 4/4 AUDIO JW1216 XX C1220 C1203 JW1217 C1227 C1204 XX C1200 JW1220 C1232...
Page 34
~ A1 Printed Wiring Board Conductor Side A ~ ~ A1 Board Semiconductor Location Table (Side A) ~ ~ A1 Printed Wiring Board Conductor Side B ~ ~ A1 Board Semiconductor Location Table (Side B) ~ - 34 -...
F3.-28DL11 AC INPUT, FUSE T3604 T3603 JW3602 H9.-28DL11 JW3601 TO LIGHTENING TO A BOARD CN3601 DISCHARGE CN406 FH3601 C3602 C3603 TO A BOARD VD3601 CN3603 T3601 CN1200 AC IN 275V 275V F3601 CHANGE CONNECTOR AC IN AC OUT TO H9 BOARD 250V CN7602 AC OUT...
~ C Board Semiconductor Voltages ~ ~ C Board IC Voltages ~ ~ C Board Waveforms ~ 20us/div 20us/div 2.32 Vp-p (H) 2.32 Vp-p (H) 20us/div 20us/div 2.32 Vp-p (H) 116 Vp-p (H) C..-28DL11 CN704 20us/div 20us/div COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL R728 R,G,B OUT R704...
SECTION 6 EXPLODED VIEWS NOTE : Items with no part number and no description are not Items marked “*” are not stocked stocked because they are seldom required for routine since they are seldom required for service. routine service. Some delay should The construction parts of an assembled part are indicated be anticipated when ordering these items.
SECTION 7 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page D2 BOARD COMPLETE Parts List : ....................48 VM BOARD COMPLETE Parts List : ....................48 A BOARD COMPLETE Parts List : ....................49 H9 BOARD COMPLETE Parts List : ....................
Page 65
• User programmable Functional Check through Infrared • Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.