Page 1
6D114E-5 ENGINE This material is proprietary to Komatsu America Corp. and is not to be reproduced, used, or disclosed except in accordance with written authorization from Komatsu America Corp. It is our policy to improve our products whenever it is possible and practical to do so. We reserve the right to make changes or improvements at any time without incurring any obligation to install such changes on products sold previously.
Page 2
Find manuals at https://best-manuals.com...
Page 3
If Any Abnormality Occurs During Operation..............3-11 Warning Lamps.........................3-12 Action Level Display...................... 3-13 Warning Lamp Table...................... 3-14 Occurred Error List Display....................3-16 Warning Lamp Details ....................3-17 Pilot Display..........................3-23 Pilot Lamp Details......................3-23 ECO Guidance.......................3-27 Gauge and Meter Display......................3-28 PC360LC-10, PC360LC-10, PC390LC-10 Find manuals at https://best-manuals.com...
Page 4
Open and Close Covers with Locks..................3-110 Lock and Unlock Engine Hood....................3-110 Lock and Unlock the Cab Door....................3-111 Battery Disconnect Switch.........................3-112 System Operating Lamp........................3-113 Komatsu Diesel Particulate Filter (KDPF)..................3-114 Manual Stationary Regeneration Procedure................3-117 PC360LC-10, PC360LC-10, PC390LC-10 Find manuals at https://best-manuals.com...
Page 5
KDPF Regeneration Disable Procedure................. 3-119 Disable Regeneration When Not Being Performed............. 3-120 Stopping Regeneration When Being Performed............3-121 Canceling KDPF Regeneration Disable................. 3-122 Komatsu Closed Crankcase Ventilation (KCCV)................3-123 KOMTRAX............................3-124 Daily Checks and Preparations Before Starting Engine..............3-126 Walk-Around Checks......................3-126 Drain Water and Sediment from Fuel Tank................3-127 Drain Water and Sediment in Water Separator..............
Page 6
Washable Cab Floor and Floor Mat..................4-41 Setting Machine at Angle......................4-44 Gas Spring Maintenance......................4-45 Bleeding Air From Hydraulic System..................4-46 Bleeding Air from Fuel Circuit....................4-48 Maintenance for First 500 Hours......................4-49 Maintenance Every 50 Hours......................4-50 PC360LC-10, PC360LC-10, PC390LC-10 Find manuals at https://best-manuals.com...
Page 7
Explanation of Attachment Components..................6-5 Hydraulic Circuit......................... 6-8 Switching Hydraulic Circuit....................6-8 Hydraulic Circuit Connection................... 6-9 Oil Flow Path......................... 6-10 Breaker Filter Element Replacement ................6-11 Breaker Pilot Element Replacement ................6-13 Attachment Guide........................6-15 Track Shoes Selection....................6-15 PC360LC-10, PC360LC-10, PC390LC-10 Find manuals at https://best-manuals.com...
Page 9
INTRODUCTION PC360LC-10, PC360LC-10, PC390LC-10 Find manuals at https://best-manuals.com...
Page 10
Komatsu cannot predict every circumstance that might involve a potential hazard when the machine is used. Therefore, the safety messages in this manual and on the machine may not include all possible safety precautions.
The following signal words alert you to information that must be followed to avoid damage to the machine. NOTICE This precaution is given where the machine may be damaged or the service life reduced if the precaution is not followed. REMARK This word is used for information that is useful to know. PC360LC-10, PC360LC-10, PC390LC-10...
Page 12
BASIC MACHINE INTRODUCTION INTRODUCTION BASIC MACHINE INTRODUCTION This Komatsu machine is designed mainly for the following types of work: • Digging • Leveling • Ditching • Loading • Demolition Directions of Machine In this manual terms front, rear, left and right refer to the travel direction as seen from the operator's seat when the operator's seat is facing the front and the sprocket is at the rear of the machine.
Page 13
Operate the machine, fully aware that the machine has a portion that an operator cannot see. Structure to Protect the Operator This machine is equipped with a structure to protect the operator (Roll-Over Protective Structure (ROPS)) conforming to ISO12117-2. PC360LC-10, PC360LC-10, PC390LC-10...
PRODUCT INFORMATION INTRODUCTION PRODUCT INFORMATION When requesting service or ordering replacement parts, please inform your Komatsu distributor of the following items: Product Identification Number, Machine Serial Number, EPA Regulations and Engine Number, and requested information from your service meter. Product Identification Number (Pin) / Machine Serial No. Plate On the bottom right of the operator's cab.
Page 15
Your Machine Serial Numbers and Distributor Machine serial No. Engine serial No. Product Identification Number (PIN) Distributor name Address Phone/Fax Service Personnel Engine Acronyms Acronym Stands For KDPF Komatsu Diesel Particulate Filter (KDPF) KCCV Komatsu Closed Crankcase Ventilator (KCCV) Variable Geometry Turbocharger PC360LC-10, PC360LC-10, PC390LC-10...
Page 17
SAFETY WARNING Please read and make sure that you fully understand the precautions described in this manual and the safety labels on the machine. When operating or servicing the machine, always follow these precautions strictly. PC360LC-10, PC360LC-10, PC390LC-10...
If the labels are damaged, lost, or cannot be read properly replace them with new ones. For details of the part numbers for the labels see this manual or the actual label, and place an order with your Komatsu distributor.
SAFETY SAFETY LABELS ⋆: If equipped. LOCATION OF SAFETY LABELS The safety label descriptions correspond to the number in the diagram. PC360LC-10, PC360LC-10, PC390LC-10...
Page 20
• Rotate cab for full view of travel path if it can done safely. • Use spotter if view is obstructed. Follow above even if machine is equipped with travel alarm and mirrors. 09802-03000 3. Warning for leaving operator's seat. (09654-03001) PC360LC-10, PC360LC-10, PC390LC-10...
Page 21
200 kV to 350 kV 350 kV to 500 kV 7.7 m (25 ft) 500 kV to 750 kV 10.7 m (35 ft) 750 kV to 1,000 kV 13.8 m (45 ft) 09801-03002 5. Warning for operating pattern. (09822-03000) PC360LC-10, PC360LC-10, PC390LC-10...
Page 22
SAFETY LABELS SAFETY 6. Warning when opening or closing front window. (09839-03000) 7. Warning when stowing front window. (09803-03000) 8. Warning for high-temperature hydraulic oil. (09653-03001) PC360LC-10, PC360LC-10, PC390LC-10...
Page 23
SAFETY SAFETY LABELS 9. Warning with high-temperature coolant. (09668-03001) 10. Warning for handling accumulator and gas spring (if equipped). (09659-53000) 11. Warning for adjusting track tension. (09657-03003) 12. Warning for handling cables. (09808-03001) WARNING PC360LC-10, PC360LC-10, PC390LC-10...
Page 24
In emergency, smash the window pane with an equipped hammer and get through there. 15. Caution against falling. (09805-13000) 16. Warning when swinging or traveling in reverse. (22B-00-21290) PC360LC-10, PC360LC-10, PC390LC-10...
Page 25
18. Beware of work equipment. (09134-A1681) Sign indicates a hazard of being hit by the working device of the machine. Keep away from machine during operation. 09134-A16381 19. Danger when handling battery. (09664-30014) 20. Prohibition of start by short-circuiting. (09842-A0481) PC360LC-10, PC360LC-10, PC390LC-10...
Page 26
23. Caution for high-temperature (09817-A0753). Sign indicates a burn hazard from touching heated parts, such as engine, motor, or muffler during or right after operation. Never touch when hot. 24. Warning to not use ether. (6732-81-4630) 2-10 PC360LC-10, PC360LC-10, PC390LC-10...
Page 28
Any modification is prohibite d. - ROPS may provide less protection if it has been s t ructurally damaged o r involved in roll-over. Consult Komatsu Distribut o r in that case. - Always wear seat belt when movin g.
Page 29
SAFETY SAFETY LABELS 31. Warning for straight travel system (STS) (Option) (20Y-62-A1731) PC360LC-10, PC360LC-10, PC390LC-10 2-13...
If you have long hair there is a hazard it may get caught up in the machine. Tie loose hair up and be cautious around all equipment and moving parts. • Check that all protective equipment functions and fits properly before using it. 2-14 PC360LC-10, PC360LC-10, PC390LC-10...
Page 31
This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...