Advertisement
Pr.
GROUP
1271
R236
Line multi-speed setting (speed 7)
1272
R237
Line multi-speed setting (speed 8)
1273
R238
Line multi-speed setting (speed 9)
1274
R239
Line multi-speed setting (speed 10)
1275
R240
Line multi-speed setting (speed 11)
1276
R241
Line multi-speed setting (speed 12)
1277
R242
Line multi-speed setting (speed 13)
1278
R243
Line multi-speed setting (speed 14)
1279
R244
Line multi-speed setting (speed 15)
1280
R401
Winding diameter monitoring reference
1281
R402
Commanded tension monitoring reference
1282
R320
Tension command cushion time
1283
R321
Cushion time reference tension
1284
R500
Taper mode selection
1285
R501
Taper setting analog input selection
1286
R503
Winding diameter at taper start
1287
R502
Taper ratio setting
1288
R510
Data table winding diameter 1
1289
R511
Data table taper ratio 1
1290
R512
Data table winding diameter 2
1291
R513
Data table taper ratio 2
1292
R514
Data table winding diameter 3
1293
R515
Data table taper ratio 3
1294
R516
Data table winding diameter 4
1295
R517
Data table taper ratio 4
1296
R518
Data table winding diameter 5
1297
R519
Data table taper ratio 5
1401
R301
Tension command increment
1402
R310
Tension command input voltage bias
1403
R311
Tension command bias
1404
R312
Tension command input voltage gain
1405
R313
Tension command gain
Commanded tension reduction scaling
1406
R340
factor during stall condition
1407
R341
Speed limit during stall condition
Tension command cushion time during
1409
R343
stall condition
1410
R530
Motor inertia
1411
R531
Empty reel inertia
1412
R532
Roll width
1413
R533
Material specific gravity
First acceleration time for inertia
1414
R535
compensation
First deceleration time for inertia
1415
R536
compensation
1418
R534
Inertia compensation cushion time
1419
R550
Mechanical loss setting frequency bias
1420
R551
Mechanical loss setting frequency 1
1421
R552
Mechanical loss 1
1422
R553
Mechanical loss setting frequency 2
1423
R554
Mechanical loss 2
1424
R555
Mechanical loss setting frequency 3
1425
R556
Mechanical loss 3
1426
R557
Mechanical loss setting frequency 4
1427
R558
Mechanical loss 4
1428
R559
Mechanical loss setting frequency 5
1429
R560
Mechanical loss 5
The initial value is for standard models.
The initial value is for separated converter types.
The setting varies with the Pr.1401 setting.
Name
0 to 6553.4
0 to 6553.4
0 to 6553.4
0 to 6553.4
0 to 6553.4
0 to 6553.4
0 to 6553.4
0 to 6553.4
0 to 6553.4
1 to 6553 mm
0 to 100 N
0 to 360 s
0.01 to 100
0 to 4
3 to 6, 9999
0 to 6553 mm, 9999
0 to 100%, 9999
0 to 6553 mm, 9999
0 to 100%
0 to 6553 mm, 9999
0 to 100%
0 to 6553 mm, 9999
0 to 100%
0 to 6553 mm, 9999
0 to 100%
0 to 6553 mm, 9999
0 to 100%
0 to 2
0 to 100%
0 to 100 N
0 to 100%
0 to 100 N
0 to 200%
0 to 60 Hz
0 to 360 s, 9999
0 to 500 kg·m
0 to 500 kg·m
0 to 5000 mm
0 to 20 g/cm
0 to 3600 s
0 to 3600 s
0 to 360 s
900 to 1100%
0 to 400 Hz, 9999
900 to 1100%
0 to 400 Hz, 9999
900 to 1100%
0 to 400 Hz, 9999
900 to 1100%
0 to 400 Hz, 9999
900 to 1100%
0 to 400 Hz, 9999
900 to 1100%
Refer to the FR-A800-R2R Instruction Manual (Roll to Roll Function Manual) for the instructions to set each parameter.
Roll to roll function related parameters
Minimum
Setting range
setting
increment
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
1 mm
0.01 N
0.01 s
0.01
1
1
1 mm
0.1%
1 mm
0.1%
1 mm
0.1%
1 mm
0.1%
1 mm
0.1%
1 mm
0.1%
1
0.1%
0.01 N
0.1%
0.01 N
0.1%
0.01 Hz
0.01 s
2
0.01 kg·m
2
0.01 kg·m
1 mm
3
0.001 g/cm
0.1 s
0.1 s
0.01 s
0.1%
0.01 Hz
0.1%
0.01 Hz
0.1%
0.01 Hz
0.1%
0.01 Hz
0.1%
0.01 Hz
0.1%
Initial
Customer
value
setting
0
0
0
0
0
0
0
0
0
1000 mm
100 N
0 s
100
0
9999
9999
0%
9999
0%
9999
0%
9999
0%
9999
0%
9999
0%
0
0%
0 N
100%
100 N
20%
1 Hz
9999
2
2
0 kg·m
2
2
0 kg·m
0 mm
3
3
0 g/cm
15 s
15 s
0 s
1000%
9999
1000%
9999
1000%
9999
1000%
9999
1000%
9999
1000%
4
33
Advertisement
