2. Specifications Classifications Specifications Washing and Dehydrating Capacity 8.0 kg Washing Method Heavy duty rotation type (centripetal current) 77 ℓ Maximum Level Standard Volume of Water 65 ℓ High Level 53 ℓ Medium Level 40 ℓ Low Level 28 ℓ Extra low level 182 ℓ...
3. Features 3-1 Dimensions 1300 1005 1005 3-2 Installation 3-2-1 Level Specifications and Wall - Clearance 3-2-3 Controlling the Front Adjustable Leg To control the height, turn the adjustable leg. Distances 1. Install the washing machine on a solid and level floor.
Page 5
3-2-5 Connecting the water supply hose 1. Remove the adaptor from the 2. First, using a "+" type screwdriver, 3. Connect adaptor to the water water supply hose. loosen the three screws on the tap by firmly tightening the adaptor. screws.
Page 7
4-2 Control Panel 4-2-(1) REMAINING TIME INDICATOR LIGHT 4-2-(6) Water Level 1. Button controls and washing processes are 1. Press this button to select the water height. displayed here. 2. The selection order is : Medium → High → Maximum → Extra Low 2.
Page 8
4-3 Function Descriptions 4-3-2 Water Level 4. This key is used as adjusting function. 1. In all the cases of prior to the first press of START/HOLD ① Rinsing times are added by one time when function key, during operating or hold state, they follow the below sequences.
Page 9
4-4 Description of Technical Points 4-4-1 Weight Recognizing Function 3. If the water level does not reach to the water level 1. Weight recognizing function works first washing selected for 60minutes after starting water operating before water is supplied, not in WOOL supplying, the water supplying Error is displaying course and Manual function operation (Wash, …...
Page 10
4-4 Description of Technical Points 4-4-5 Silver Wash Function 1. It's a new technology of washing by Silver Nano system Ag+ Nano will be launched and mixed with water inside a case and flown down to tub if this key is pressed. Kill bacteria and detergent polluted 2.This can only be selected when WASH, RINSE and SPIN are all selected.
6. Disassembly and Reassembly 6-1 Cautions for Disassembly and Reassembly 6-1-1 Before Servicing 1. When laying down the washing machine for repair, Shape do not place the front side downwards. This may CASE-D BAR-S SPRING COLLOR-S cause the following : The round front face may be deformed.
Page 15
6-2 Disassembly Disassembly Procedure Illustration ◆ Removing the Top cover and PCB Assembly 1) Remove screw cover and screw A. 2) Loose 5 screws for fastening the PCB-Assembly. 3) Take out the PCB-Assembly. 4) Remove 2 screws at the front of the top-cover. 5) Remove 2 screws fixing the parts in back of the top-cover.
Page 16
Disassembly Procedure Illustration Remarks ◆ Removing the Motor 1) Remove the Back Cover. 2) Lay down the Washing Machine with the rear side facing the floor. 3) Pull out the Sound Absorption Panel. 4) Remove the Wire Housing. 5) Remove the V Belt. 6) Remove the two Bolts fastening the Motor.
Page 17
6-3 Spin - Nut Repairing Box 6 HANDLE 5 CONNECTING ROD 4 GUIDE 3 JIG 2 SPIN NUT 1 SHAFT ⑤ ⑥ 6-3-1 Procedure 3. Insert the connecting rod and handle into the square box. Then turn the handle clockwise on ③...
7. Troubleshooting 7-1 Self - diagnostic Functions (Buzzer Alarm) ERROR CONDITION BUZZER DISPLAY SOLUTION 0.5sec ON/OFF Press POWER KEY In case DOOR is opened during the LID OPEN Sounding ERROR intermittent or ordinary dehydration. and close DOOR. 5 times 0.5sec ON/OFF Press POWER KEY -In case 3-times UNBALANCE are sensed UNBALANCE...
Page 19
7-2 Test Mode (1) Auto Operating Part Test Mode a. Initial Access Mode: Turn on the course, manual and power keys at the same time b. Mode Switch: Use the water level keys to switch the mode c. Display and Control in Initial Access Mode ( ※ Error Detection should occur less than 3 seconds after the machine starts operating) "01"...
Page 20
- Press the Start key 5 times: "HA" is displayed => Weight Detection (This should be performed right after the motor stops and the pulse value and the water level are displayed) - Press the Start key 6 times: END (Auto power S/W operation) => The Auto Power S/Wshould initiate within 2 seconds (for mechanical switches).
Page 21
- Press the Start key 5 times: "HA" is displayed => Weight Detection (This should be performed right after the motor stops and the pulse value and the water level are displayed) - Press the Start key 6 times: END (Auto power S/W operation) => The Auto Power S/Wshould initiate within 2 seconds (for mechanical switches).
Page 22
d. 02 Mode : Weight Detection - When the operating key is pressed with "02" on the display, weight detection is performed. - When done, the result is displayed on the segment in decimals. - During the detection process, the water level LED is also displayed. e.
Page 23
7-3 Servicing Precautions When trouble shooting or parts, be sure to observe 5.Be sure to use only authorized replacement parts. the following. 6. AC 110V-220V is applied between T1 and T2 of the 1. Be sure to let the resistance of 1 contact the triac on the P.C.B Therefore, touching the radiating human body before grounding.
Page 24
7-4 Troubleshooting 7-4-1 Trobleshooting of the Power Supply Board If any of the following occurs, the PCB is defective. Replace the PCB. 1. Pressing a selection button illuminates the LED display, but the buzzer does not sound. 2. Pressing a selection button sounds the buzzer, but does not illuminate the LED. 3.
Page 26
Water Stop Error Washing is started without water supply.
Page 27
The pulsator does not rotate during washing. This malfunction may be caused by defective contacts of the wire harness.
Page 28
Defective Rotation during Washing Noise Occurs during Washing. (The following soond does not indicate any problem : The "Sha" sound generated during the stop of the dehydration tub is the sound of the water moving by automatic balance in the dehydration tub.)
Page 31
No draining. (With PUMP MODEL) 7-4-4 Inspection After Repair Inspection Item Description Check that the original grounding wire of the washing machine is securely grounded. Check grounding Connection of the grounding wire? wire to a gas or water pipe made of vinyl chloride is very dangerous.