Sealey TC115 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
1.1. ELECTRICAL SAFETY
 WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information: it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fi tted with the
correct fuse - see fuse rating in these instructions.
 DO NOT pull or carry the appliance by the power cable.
DO NOT pull the plug from the socket by the cable.

 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
replaced immediately by a qualifi ed electrician.
1.1.4. This product is fi tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualifi ed electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualifi ed electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
B) Connect the BROWN live wire to the live terminal 'L'.
C) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualifi ed electrician.
1.2. GENERAL SAFETY
Familiarise yourself with the application, limitations and potential hazards of the tile cutter.

 WARNING! Disconnect the cutter from the mains power before changing accessories, servicing or performing any maintenance.
 The machine must only be serviced by a qualified person or service agent. Contact your Sealey stockist for information.
 Place the cutter on a supporting surface strong enough to take the weight of the machine and work piece during operation.
 Keep the work area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
 Inhaling dust can be harmful - always wear respiratory protection and ensure that there is adequate ventilation.
 Maintain the cutter in good condition, check moving parts alignment regularly. Keep cutting disc clean and in good condition.
 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.
 A guard, or any other part, that is damaged must be repaired or replaced before the tool is next used. The safety guard is a
mandatory fitting when the cutter is used on premises covered by the Health & Safety at Work Act.
Before commencing work, ensure the cutting disc is mounted correctly, securely fastened and is compatible with the machine, spindle

speed and the material to be cut. Never use a cutting disc which is damaged, bent or warped. Use only recommended cutting discs.
 Remove adjusting keys and wrenches from the machine and the vicinity before turning it on.
 WARNING! Wear approved safety eye protection, ear defenders and respiratory protection. A full range of personal safety equipment is
available from your Sealey stockist.
 Remove ill-fitting clothing, ties, watches, rings and other loose jewellery and contain long hair.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the work area.
 Avoid unintentional starting and never leave the cutter running unattended.
 DO NOT use the cutter for a task for which it is not designed.
 DO NOT get cutter wet or use in damp or wet locations or areas where there is condensation.
 DO NOT use cutter where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning
rags etc.
 DO NOT operate the cutter if any parts are damaged or missing as this may cause failure and/or personal injury.
© Jack Sealey Limited
Ø115MM PORTABLE TILE CUTTER
MODEL NO:
Wear safety
Wear protective
gloves footwear
Original Language Version
TC115
Wear protective Wear ear
clothing protection
Wear a mask Indoor use
only
Replacement fuse
rating: 5A
TC115 Issue 1 19/02/21