DeWalt DCD200 Original Instructions Manual page 13

installing attachments or accessories. An accidental
start‑up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
5
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
6
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Cable Removal from the Drain Cleaner and
Cable Drum Installation (Fig. A)

WARNING: To reduce the risk of injury, wear safety
goggles or glasses with side shields. Always wear leather
gloves with latex gloves inside. The cable is under stress
and can uncoil unexpectedly. Cable end feature may
be sharp.
Remove the cable for cleaning after each use.
To Remove the Cable
1. Remove the battery pack from the tool.
2. Pull the front handle 10 out away from the tool to the
unlocked position.
3. With the tool supported vertically, remove the four screws
from the drum cover .
9

WARNING: The cable is under stress and can uncoil
unexpectedly. Keep pressure on the drum cover so it does
not uncoil.
4. Carefully lift the drum cover up, reach underneath to hold
the cable firmly while pulling off the drum cover
front handle 10 to expose the inner drum
WALT battery packs and chargers.
5 is fully charged.
and firmly pull the battery pack
9 and
12 .
5. Remove the cable from the drum cover and front handle
and tuck it into the inner drum. Set the drum cover aside.
6. Carefully remove the inner drum with cable from
the drain cleaner.
7. When cleaning the cable, carefully uncoil the cable from the
inner drum. Refer to Cleaning under Maintenance.
To install the Cable
1. Remove the battery pack from the tool.
2. Pull the front handle out away from the tool to the
10
unlocked position.
3. Remove the four screws from the drum cover
4. Fully wind the clean, dry cable into the inner drum
following the cable direction symbol

WARNING: Winding the cable in the wrong direction
could cause the tool to apply excessive torque causing the
cable to kink during bind up.

WARNING: Never install a new cable by threading it
through the front handle on the tool. Always disassemble
the drum cover so you can be sure the cable is wound in
the proper direction.
5. Place the inner drum with cable back into the tool.
6. Carefully pull the cable bulb end out of the inner drum and
feed it through the front handle.

WARNING: The cable is under stress and can unwind
unexpectedly. Keep pressure on the cable so it does
not unwind.
7. Place the drum cover and front handle over the inner drum
and reinstall the four screws. Tighten securely.
nOTE: If the unit is unbalanced and/or vibrates
unnecessarily, the cable may be wound poorly.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.

WARNING: Always wear eye and other protective
equipment appropriate to the task.

WARNING: Always wear leather work gloves with latex
gloves inside.

WARNING: Do not operate if more than 15 cm of cable is
outside of pipe or drum.

WARNING: The cable can whip or tangle.

WARNING: Do not hold cable while it is turning.

WARNING: Cable end feature may be sharp.
English
9 .
12
(Fig. A).
14
11