Maintenance - AEG PM10E Instructions For Use Manual

TECHNICAL DATA
Nominal power output .............................................................
Rated output ............................................................................
No-load speed .........................................................................
Speed under load ....................................................................
Rate of percussion under load ................................................
Single impact strength .............................................................
Drilling capacity in concrete .....................................................
Tunnel bit in concrete, bricks and limestone ...........................
Core cutter in concrete, bricks and limestone .........................
Weight without cable ...............................................................
Typical weighted acceleration in the hand-arm area ...............
Typical A-weighted sound levels:
Sound pressure level ............................................................
Sound power level ................................................................
Wear ear protectors!
Measured values determined according to EN 50 144.
PM 10 E:
Typically the A-weighted sound pressure level of the tool is ...
Wear ear protectors!
Measured values determined according to 2000/14/EG at the
user's ear.
2000/14/EC: Conformity assessment procedure according to
Annex VI.
Notified Body: VDE Testing and Certification Institute,
Merianstr. 28, 63069 Offenbach, Germany
Measured sound power level ..................................................
Guaranteed sound power level ...............................................
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached
leaflet!
Appliances used at many different locations including open air
must be connected via a current surge preventing switch.
Always wear goggles when using the machine. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Sawdust and splinters must not be removed while the machine is
running.
Always disconnect the plug from the socket before carrying out
any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Always use the auxiliary handle, even if the machine has a safety
clutch since this safety clutch only engages when the machine
blocks with a jerk.
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Under the effect of extreme electromagnetic interferences from
the outside, tempo-rary variations in the speed of rotation could
arise in particular cases.
SPECIFIED CONDITIONS OF USE
PN 11 E: The pneumatic hammer can be universally used for
hammer drilling and chiselling in stone and concrete.
PM 10 E: The hammer can be used for chiselling and demolition.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 50144, EN 55014-1, EN 55014-2, EN 61000-3-2,
EN 61000-3-3, in accordance with the regulations 98/37/EC,
89/336/EEC, 2000/14/EC (PM 10 E).
Winnenden, 2004/11/10
19 ENGLISH
Volker Siegle
Manager Product Development
PN 11 E
.......................1700 W .........................1600 W
.........................850 W ...........................800 W
..................125-250 min ............................-
-1
..................125-250 min ............................-
-1
................975-1950 min ..............975-1950 min
-1
........................7-27 J ............................7-27 J
......................28-50 mm .............................-
......................50-80 mm .............................-
....................45-150 mm .............................-
........................ 11,8 kg .......................... 11,0 kg
...........................10 m/s .........................10 m/s
2
.........................100 dB (A) .........................-
......................... 113 dB (A) .........................-
.................................................................91 dB (A)
...............................................................105 dB (A)
...............................................................107 dB (A)
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the system
voltage indicated on the rating plate. It is also possible to
connect to sockets without an earthing contact as the design
conforms to safety class II.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all
times.
Important note! If the carbon brushes are worn, in addition to
exchanging the brushes the tool should be sent to after-sales
service. This will ensure long service life and top performance.
Use only AEG accessories and spare parts. Should components
need to be exchanged which have not been described, please
contact one of our AEG service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or
directly at: AEG Elektrowerkzeuge, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard
equipment, available as an accessory.
PM 10 E
-1
2