Table of Contents
Advertisement
Available languages
Available languages
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, keep away from the forward and reverse
buttons while making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Inserting and Removing Bits (Fig. C)
nOTE: The hex spindle
4
accessories only.
To install a bit simply insert it into the cavity in the hex
spindle
4
as shown in Fig. C.
To remove the bit, pull it straight out from the hex spindle.
OPERATION
WARNING: To reduce the risk of serious personal
injury, keep away from the forward and reverse
buttons while making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
This screwdriver is intended for tightening and loosening
screws, nuts, and the like and is not equipped with an
impacting mechanism.
Proper Hand Position (Fig. A, D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the
main handle
3
.
LED Worklight (Fig. A)
CAUTION: When using the worklight for purposes
other than screwdriving or drilling be sure to
remove all accessories. Unused accessories could
cause injury or property damage.
CAUTION: Do not stare into the LED. Serious eye
injury could result.
When the screwdriver is activated by pressing the On/Off
switch
1
, the LED worklight
The LED worklight will turn off after the On/Off switch
been released.
Switching On and Off (Fig. A)
NOTE: When the screwdriver is activated by pressing the
On/Off switch
1
the LED worklight
illuminate.
1. To run the screwdriver, press the On/Off switch
2. To stop the screwdriver, release the On/Off switch
3. To lock the tool in the off position, move the forward/
reverse/lock-off slider
Forward/Reverse/Lock-off Slider (Fig. E)
For tightening screws, use forward rotation. For loosening
screws, use reverse rotation.
1. To select forward rotation, push the forward/reverse
slider
2
to the right hand position.
accepts 1/4" (6.4 mm) hex
5
will automatically turn on.
5
will automatically
2
to the center position.
2. To select reverse rotation, push the forward/reverse slider
2
to the left hand position.
3. To lock the tool, set the forward/reverse slider into the
center position.
nOTE: When the forward/reverse/lock-off slider
in the center position the tool is locked-off to prevent
accidental actuation or battery discharge.
Screwdriving
NOTE: For best performance, #8, 2" and smaller fasteners are
recommended, or screw into pre-drilled holes.
1. Grasp the screwdriver as shown in Fig. D.
2. Insert the appropriate screwdriver bit into the hex
spindle
3. Select forward or reverse rotation using the forward/
reverse/lock-off slider
4. To run the screwdriver, press the On/Off switch
5. To stop the screwdriver, release the On/Off switch
screwdriving notes:
•
Do not use double ended screwdriver bits.
•
Do not use screwdriver as a pry bar in any position.
•
To avoid screwdriver being turned on accidentally, do not
carry in your pocket.
Hints for optimum use
screwdriving
•
Always use the correct type and size of screwdriver bit.
•
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
•
Always hold the tool and screwdriver bit in a straight line
with the screw.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
1
has
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by BLACK+DECKER, have not been tested with
this product, use of such accessories with this tool
1
.
could be hazardous. To reduce the risk of injury, only
1
.
BLACK+DECKER recommended accessories should be
used with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact BLACK+DECKER call 1-800-544-6986 .
4
.
2
.
English
2
is
1
.
1
.
7
Advertisement
Table of Contents
