6. Disassembling the top cover assembly. 1. DISASSEMBLING PROCEDURE 1) Remove two screws (A325) and remove the 1. Remove the battery and the SmartMedia. black & white LCD block (H003). 2) Set the mode dial to “Auto photography mode” 2. Remove four screws (A110), one screw (A370) as below.
6. PARTS LIST Location Part Number Number Description UC01 23784712 PC BOARD ASSY, PB9456-1 UD01 23784711 PC BOARD ASSY, PB9456-2 UM01 23784713 PC BOARD ASSY, PB9456-3 US01 23784715 PC BOARD ASSY, PB9457-1 UT01 23784971 PC BOARD ASSY, PB9457-2 U004 23005093 LENS BLOCK W011 23389110...
FILE NO. 210-200315 SERVICE MANUAL DIGITAL STILL CAMERA CREATED IN TAIWAN, JUL, 2003...
Page 9
TOSHIBA PDR-M700 Service Manual Section Description Pages 1. System Overview 1-1. System Diagram Block Diagram 1-2. System Overview Camera System Introduction 2. Disassembly / Assembly 2-1. Disassembly Operation Steps of Disassembly 2-2. Assembly Operation Steps of Assembly 3. Calibration Camera Calibration 4.
Page 10
1. System Overview Section 1-1 System Diagram SD Card PDR-M700 Block Diagram MAIN PCB SD Card Switch MIC EXT .MIC Connector INT .MIC SCDA1A0801 K4S281633D-RL K4S281633D-RL M28W320ECT70ZB6 TK15467S SPEAKER SDRAM SDRAM Flash Memory 75ohm Driver AV OUT LCD PCB AK4536 NJM2135 CODEC MEMA[13:0]...
1-2 System Overview The PDR-M700 consists of 7 PC boards (the Main PCB, CCD PCB, Flash PCB, LCD PCB, Switch PCB, Mode PCB and Shutter PCB), a lens unit, a color LCD, a color EVF unit, a flash unit, etc. The lens unit consists of a CANON 10X zoom lens and built-in shutter motor, an aperture motor, a zoom motor and a focus motor.
Page 12
1-2-1. Startup operation When batteries are loaded or the AC adaptor is connected, a 3.0V voltage for the sub-CPU is generated by U402 and supplied to the sub-CPU (U405). When the POWER switch (S800) is turned on in this status, the camera switches to the boot-up sequence. The sub-CPU (U405) conducts the power on control until the main voltage supplied to the DSP (U901) and other parts is supplied.
Page 13
1-2-8. Adjustment data and camera setting data The CCD scratch data and the AF, AE, AWB and other camera adjustment data is written in the FROM (U304). Menu setting data is written in the sub-CPU (U405). The sub-CPU data is retained as long as the voltage of the secondary coin battery on the Main Board is 1.8V or greater. 1-2-9.
Page 14
2. Disassembly / Assembly Section 2-1 Disassembly Step Figure Discription Remark Tools Check if there's Finished Product any scratch on the surface. Remove the screws 01635-236*5 from the Screw driver camera Open the Card Cover A260 and the Jack Cover A250. Remove the Rear The Battery Cover Assembly carefully not...
Page 15
Remove the screws 01635-350*2 from the camera to remove the Screw driver base of Mode Dial A410. Remove the screw 01635-149 from the Tripod Holder A340. Screw driver Remove the Flex Cable Tweezers Main-LCD H600 from the Main PCB ASSY U100.
Page 16
Detach the Flex Cable Detach the Flex Main-Mode H610 to Cable Main-Mode remove the Main PCB H610 from the ASSY U100 from the Mode PCB ASSY camera. U510. Discharge the solder joints of big capacitor Discharger beside the Flash PCB Tweezers KIT U300.
Page 17
To disassemble the Speaker ASSY H310 (after step 5) De-solder the wires from the Speaker ASSY Soldering iron H310. Then remove it Tweezers from the back of LCD with tweezers carefully. To disassemble the Color LCD sub-assembly (after step 5a) Remove the screws 01635-223*3 and 01635-000*1 on the...
Page 18
Rear Cover ASSY 5a17 A110. To disassemble the Card Cover sub-assembly (after step 5) Remove the two screws Screw driver 01635-086*2 as shown. Remove the Card Cover 5a21 Tweezers metal plate. Push the Card Cover 5a22 Tweezers pins. 5a23 Card Cover A260. To disassemble the Microphone sub-assembly (after step 14) Remove the sticked Microphone ASSY...
Page 19
To disassemble the Battery terminals sub-assembly (after step 15) The top view of camera of step 15. Remove the screws Open the cap of 01635-042*2 of Shutter connector before Screw driver 15a1 PCB ASSY U520 and remove the Shutter Tweezers take off the Shutter PCB PCB U520 as ASSY.
Page 20
To disassemble the Photo Sensor sub-assembly (after step 22) Remove the Photo Sensor ASSY H500 as shown. The wires had Tweezers been sticked by the sponge.
Page 21
2-2 Assembly Step Figure Discription Remark Tools Install all the Battery Terminal A600 and drive the screws 01635- Screw driver 164*4 to the Battery Chamber. Install the Battery Chamber into the Main Frame A300. Drive the screw 01635- 010 of Main Frame Screw driver A300.
Page 22
Install the Photo Sensor ASSY H500 to the camera. Check the Flash Install the Flash Open Open Switch Switch A440. Then A440 can work install the Flash PCB well before KIT U300 into the assemble the Flash camera. PCB KIT U300. Drive the screw 01635- 000 to the Flash PCB Screw driver...
Page 23
Install the Jack Cover ASSY A250 as shown. The Microphone Assemble the Front ASSY H320 Cover ASSY A100 to might be inserted camera. Check the on the Front position of Power Cover ASSY. Switch first. Connect the wire of Microphone ASSY Screw driver H320 to camera.
Page 24
Finished Product To assemble the Card Cover ASSY A260 (before step 25) Card Cover A260. Insert the Card Cover 25a1 Tweezers pins. Install the Card Cover 25a3 Tweezers metal plate. Drive the two screws 25a4 Screw driver 01635-086*2 as shown. To assemble the Rear Cover sub-assembly (before step 25) The Color LCD Drive the screws 01635-...
Page 25
Install the Electric View Finder H220. Connect 25b3 the wire. Drive the Screw driver screw 01635-000 to fix Install the Switch PCB ASSY U500 carefully 25b4 not to damage the cap of the connector. Drive the screws 01635- The Switch PCB 223*3 and 01635-000*1 25b5 Holder (metal...
Page 26
3. Calibration Section 3-1 The items need to be calibrated Change parts Part Sensitive Focus Strobe Firmware Code Aperture update Shutter Defect pixel White balance Lens Module H100 Color LCD H200 Electric View H220 Finder Photo Sensor H500 Main PCB U100 Flash PCB KIT U300...
Page 27
3-3 LCD Calibration Procedure Tools: AC Adapter SD Card with Calibration Firmware Oscilloscope Test Points: Please look at figure 3.3.1. GND (TP608) (TP601) (TP602) (TP600) PSIG (TP610): Trigger Signal figure 3.3.1. The setting of Oscilloscope: CH1(G) : AC,1V /div, 20us/div; (TP602) CH2(R&B) : AC, 1V/div, 20us/div;...
Page 28
Fig. 3.3.2 2. Press the UP/DOWN button to select the item LCD. Then press the RIGHT button to enter LCD menu. Menu items are shown as figure 3.3.3. Press the DISP button to initialize LCD setting. If the image on LCD is NG, press MENU button at most 6 times to let it become normal.
Page 29
5. The setting range of Oscilloscope is AC, 1V/div, 20us/div for the observation of the waveform of G signal (TP602). Press the UP/DOWN button to select the item U_CNT. Then press the RIGHT button. Then Press UP/DOWN to set G signal of the black / white peak-peak to 3.0 +/- 0.1V as shown in figure 3.3.5. Then press OK button to return.
Page 30
Fig. 3.3.7 8. The setting range of Oscilloscope is AC, 500mV/div, 20us/div, “INV”, “ADD” for the observation of the waveform of G signal (TP602) and B signal (TP600). Press the UP/DOWN button to select the item B_CNT. Then press the RIGHT button.
Page 32
3-4 EVF Calibration Procedure Tools: AC Adapter SD Card with Calibration Firmware Oscilloscope Test Points: Please look at figure 3.4.1. (TP705) R signal (TP701) G signal (TP702) B signal (TP703) COM signal (TP704) : Trigger Signal figure 3.4.1. The setting of Oscilloscope: Trigger: COM signal (TP704) GND: GND (TP704) CH1(G): AC,1V/div, 20us/div;...
Page 33
Press the UP/DOWN button to select the item EVF. Then press the RIGHT button to enter EVF menu. Menu items are shown as figure 3.4.3. Press the DISP button to initialize LCD setting. Fig. 3.4.3 Press the UP/DOWN button to select the item VCO. Press the RIGHT button, then adjustment screen will be changed to EVF from LCD.
Page 34
3.5+/-1.8V 2.3+/-0.12V Fig. 3.4.6 Press the UP/DOWN button to select the item U-BRT. Then Press the RIGHT button. Press UP/DOWN to adjust the waveform of G signal shown as figure 3.4.5. The black level to black level peak-peak voltage should be adjusted 3.5 +/- 1.8V. Then press OK button to return. The setting range of Oscilloscope is AC, 500mV/div, 20us/div, “INV”, “ADD”...
Page 35
G signal (TP702) and B signal (TP703). Press the UP/DOWN button to select the item B_CNT. Then press the RIGHT button. Then press UP/DOWN to set G-B signal shown as figure 3.4.9. The waveform within 1H should be adjusted flat. Then press OK button to return. Fig.
Page 36
3-5 Sensitive, Aperture, and Shutter Calibration Procedure Tools: AC Adapter SD Card with Calibration Firmware Light Source : Light value is 12+/-0.1 EV; Color temperature is 5100+/-300K. (Fig. 3.5.1) Fig. 3.5.1 Procedure: Install the SD Card with calibration firmware into camera. Close the card cover. Attach camera to AC Adapter.
Page 37
Put the camera in front of the Light Source. The distance between Lens and Light source is from 1cm to 2cm. Then press OK button to proceed with the adjustment automatically. If the adjustment is OK, it will display SUCCESS as shown in figure 3.5.7.
Page 38
3-6 Strobe Calibration Procedure Tools: AC Adapter SD Card with Calibration Firmware 18% Gray Chart: Size 1.0m(W) * 1.0m(H) Dark room: Prepare an environment allowing a complete light sealed. Test distance: Between lens and chart is 0.9+/-0.1m. Procedure: Install the SD Card with calibration firmware into camera. Close the card cover. Attach camera to AC Adapter.
Page 39
Repeat the steps above #6 & #7 several times until the LCD displays SUCCESS while the adjustment is OK shown as figure 3.6. . Press the LEFT button to return. Fig. 3.6.5 If the variable resistor had been turned to 360 degree but the strobe calibration is still fail, the camera is NG.
Page 40
3-7 Defect Pixel and White Balance Calibration Procedure Tools: AC Adapter SD Card with Calibration Firmware Light Source : Light value is 12+/-0.1 EV; Color temperature is 5100+/-300K. (Fig. 3.5.1) Procedure: Install the SD Card with calibration firmware into camera. Close the card cover. Attach AC Adapter to camera.
Page 42
3-8 Focus Calibration Procedure Tools: AC Adapter SD Card with Calibration Firmware Collimator Lens ; f = 450mm Chart: Supplied as PDF file “TEST_CHART.pdf” used by printing on A3 size. Test distance : Between collimator lens and chart is 450mm. (Please confirm collimator lens manual so that the distance of camera and chart may be infinity.) Procedure: Install the SD Card with calibration firmware into camera.
Page 43
3-9 F/W Update Procedure Tools: AC Adapter SD Card with Update Firmware Procedure: Install the SD card with firmware update program into camera. Close the card cover. Attach AC Adapter to camera. Keep pressing the ERASE button and then slide the Power switch to power on the camera.
Page 44
4. Troubleshooting Section Item Status Analysis How to fix No Image at shooting CCD FPC break Replace the Lens Module ASSY(H100). CCD NG AD coverter NG TG NG CCD PCB NG Width line noise and Length Width line noise or Length line noise is occurred on Replace the Lens Module ASSY(H100).
Page 45
UP, CENTER, DOWN, Swith (S809, S810, S811, S812, S813, S814, S815) Replace the LCD PCB ASSY(U410). LEFT, TRUSH, DISP, Replace the Flex Cable Main-LCD(H600). MENU key are not effective Finder LED (Red and LED drive transister (Q801) NG Replace the Switch PCB ASSY(U500). Green) is not flash Poor Connection Replace the Main PCB ASSY(U100).
Page 48
5-2 Camera Part Photo Part Code Parts Name Description Q'ty/Unit Toshiba P/N Premier P/N Mechanical Parts A100 Front Cover ASSY P000382700 9D384-0004 A110 Rear Cover ASSY P000382710 9D384-0009 Battery Cover A140 P000382720 9D344-7000 ASSY A250 Jack Cover P000382730 9D384-0010 A260...
Page 49
Part Code Parts Name Description Q'ty/Unit Toshiba P/N Premier P/N A600 Battery Terminal P000382790 9D335-013 A900 Screw Kit P000382800 9D384-1635 Module H100 Lens Module ASSY P000382810 9D346-0000 H200 Color LCD P000382820 9D384-0011 Electric View Finder H220 P000382830 9D346-1000 ASSY H310...
Page 50
Part Code Parts Name Description Q'ty/Unit Toshiba P/N Premier P/N Flex Cable Main- H600 P000382870 9D337-103 Flex Cable Main- H610 P000382880 9D337-105 Mode H620 LCD Wire 2P P000382890 02547-201C Board Assembly U100 Main PCB ASSY P000382900 9D347-4000 U300 Flash PCB KIT...
5-3 Screw List Specification Part Name Position Used Flash PCB kit*5, Main Frame*1, 01635-000 Main PCB*3, Elec. View S:1.7*3*A0.5 BL Finder*2 Mode PCB*2, Battery 01635-010 S:1.7*2.5*A0.5 BL Chamber*1 Color LCD Holder*3, Shutter 01635-042 S:1.7*2*A0.5 BL PCB*2, Battery Chamber*2 01635-086 Card Cover*2 S:1.2*2*A0.4 BL 01635-148 LCD PCB*3...
Page 52
6. Packing Parts Section 6-1 Packing Explode Diagram Y720 Y430 Y440 Y340 Y200 Y220 Y410 Y500 Y400 Y600 Y900 (Y900 is A model only.) Y112 (Y112 is E model only.) Y110 Y100 Y710 (Y710 is partition.) Y700...
6-2 Packing Part List Part Code Parts Name Pcs/Set Remark Y100 CD-ROM Y110 Instruction Manual E model only Y112 Instruction Manual Y200 USB Cable Y220 AV Cable Y340 Alkaline Battery Y400 Camera Case Y410 Shoulder Strap Y430 Lens Cap Y440 Adapter Ring Y500 IR Remote Controller...
Page 54
A100 Front Cover ASSY COVER ASSY, FRONT, GRAY, PDR-M700 China 9D384-0004 P000382700 Rubber, Remote Cover, Front LCD Cover, Rating Label, Toshiba Logo and Tripod Holder. Cover, Card Cover, 5-key&Menu&Delete A110 Rear Cover ASSY COVER ASSY, REAR, GRAY, PDR-M700 China 9D384-0009 P000382710 Buttons, Zoom Buttons, Flash&Timer Buttons,...
8. Specifications Section Model name PDR-M700 Sensor 1/2.7” CCD sensor (total pixel count: Approx. 3.37 million) Sensitivity Manual setting: Equivalent to ISO 70/100/200/400 Automatic setting: Equivalent to ISO70/100/200/400/70 to 200/70 to 400 Lens 10X optical zoom lens F2.8 - F3.1 Focal distance f=5.7 mm - 57 mm (equivalent to 37 mm - 370 mm on a 35 mm camera) Finder...