Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Philips UrbanSpark
Summary of Contents for Philips UrbanSpark
- Page 1 UrbanSpark Mounting Instructions (V3.1)
- Page 2 Important Safety Notice The battery presents a risk of electrical shock and a high short circuit current. The Signify mounting instructions must be strictly followed, otherwise potential application, reliability, or safety issues may arise. Contact your local Signify service if the instructions cannot meet special field conditions.
-
Page 3: Field Selection
Field selection Avoid Locations in the shade of the trees or buildings, if you can not avoid the shade, you must ensure the shade below the 2m of the pole. If you do want to install the system at a shade area, please consult to Signify professional people. Pole foundation and anchor bolts M20 nuts (Advise material: SUS) Note:... -
Page 4: Part List
Tools M8 Socket screw T30 6 Lobe pin drive key Spanner Multimeter Cross Steel rope wrench (Size:5) (Part of supply) (optional) (Max open size>30mm ) screwdriver (Φ1.5Mm, length=8m) Note: The tools listed do not include items needed for pole installation and other construction work. Part list Note: Luminaire may be different according to different requirements. -
Page 5: Pole Assembly
Pole and base plate Assembly (Applicable for both 4m and 6m) Soft Soft cushioning cushioning Hard Block Hard Block 1. Rest the pole over two resting blocks as Note: Recommended size of resting shown. block (Not part of supply). M10 Screw M10 Screw M10 Washers (2x) M10 Washers (2x) - Page 6 2.Fix the PV cartridge with pole using M8 screws as shown. torque torque 8 N.m 8 N.m 3.Open the 8 Nos rubber covers and tight all M6 screws using cross head screwdriver. Then affix back the rubber covers. torque torque 2.5 N.m 2.5 N.m 6m Pole Assembly (OR)
- Page 7 4.Connect both MC4 connectors of PV cartridge top cable to the 4m long MC4 extension cable, then Insert the PV cartridge top to the pole as shown. 6. Fix the top cover back to 5.Pass cable through the cutout provided (at top) and then PV Cartridge top as shown.
- Page 8 Luminaire Assembly (for both 4m and 6m) Pull the luminaire cable using steel rope from service hatch and tighten screws to affix the luminaire. Note: Refer luminaire mounting instruction sheet for luminaire fixing guidelines. Affix the pole Erect the Pole by Crane (For both 4m and 6m) (For both 4m and 6m) Lift by crane...
-
Page 9: System Connection
System Connection Must strictly follow the below sequence, or it will introduce difficulty on installation. 2a. Affix controller on the mounting bracket using four M4 Screws. 1. Put battery into the pole. 2b. Mount the bracket on C- Clamp using knurled head screws as shown. -
Page 10: Check List For Installation
Check List for Installation (This checklist MUST be signed by the installer before system installation handover) Project Name Project Location Scope of check Site Consrtuctor No. Item Description Result Remark Installation If the installation location avoid the □ yes □ No location shade of the trees or buildings If structural strength of base meet... -
Page 11: Troubleshooting
Troubleshooting Firstly,Check if you were followed the connection sequence we mention prior. If not, please disconnect one of the battery cable, and reconnect it, wait for 2-5 minutes, if still no light, please check below steps:- Check if the the connection of luminaire is Luminaire disconnect loose Replace a luminaire which is compatible to... -
Page 12: Maintenance
Maintenance Maintenance Panel :- 1. Normally you don't need to clean the panel frequently, it depends on the local environment. 2. In heavy dust area, it is required to clean the solar module regularly with a damp towel to guarantee optimum performance of the solar panel. 3. -
Page 13: Battery Replacement
Battery replacement 2. Follow the disconnection 3. take the old 4. Affix controller 1. Open the sequence (refer page 2) to battery out and service disconnect the charge replace a new hatch. controller and take out the one. charge controller Notice: Turn on/Turn off delay time is about 5 minutes.