Advertisement
Get started
3
1 The batteries are pre-installed in the handset. Pull
the battery tape off from the battery door before
charging.
2
a welcome message (country dependent).
3 Set the country and language if prompted.
4 Set the date and time.
• If the time is in 12-hour format, press
select [am] or [pm] (country dependent).
Charge your phone
Charge 8 hours
> 70%
10% - 40%
40% - 70%
< 10%
Flashing: low battery
www.philips.com/support
To access the user instructions online, use the
reference model number written on the product
label at the bottom of the base station.
2021 © MMD Hong Kong Holding Limited.
All rights reserved. Specifcations are subject
to change without notice.
This symbol on a product means that
the product is covered by European
Directive 2012/19/EU.
This product has been manufactured
by, and is sold under the responsibility
of Hong Kong Holding Limited and
Hong Kong Holding Limited . is the
warrantor in
relation to this product.
Philips and the Philips Shield Emblem
are registered trademarks of Koninklijke
Philips N.V. and are used under license
from Koninklijke Philips N.V.
Enjoy
4
Phonebook
Add record
1 Press
.
2 Select [Phonebook] > [Add new].
3 Follow on-screen instructions.
Call from the phonebook
1 Press .
2 Select a record and press
Direct access memory
You have 2 direct access memories (Keys 1 and 2).
To dial the saved phone number automatically, press
and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to the voice mail number and information
service number of your service provider respectively.
/
to
(network dependent).
Call log
Call from the call log
1 Press
.
2 Select a record and press
View record
> [View].
Press
>
Save record
1 Press
>
2 Follow on-screen instructions.
Delete record
1 Press
>
2 Follow on-screen instructions.
Redial list
Call from the redial list
1 Press
.
2 Select a record and press
Save record
1 Press
>
2 Follow on-screen instructions.
Delete record
1 Press
>
2 Follow on-screen instructions.
Telephone answering machine
(for M455 only)
Record an announcement
1 Press
> [Answ. Machine] >
[Announcement].
2 Follow on-screen instructions.
Listen to the incoming messages
> [Answ. Machine] > [Play].
Press
Delete an incoming messages
1 When you listen to the message, press
enter the options menu.
2 Select [Delete], then press
Register additional handsets
You can register additional handsets to the base
station.
1 Press
.
2 Select [Services] > [Register], then press
3 Press and hold
10 seconds.
4 Enter the system PIN/passcode (0000).
5 Press
Registration is complete in less than 2 minutes.
Restore default settings
You can reset your phone settings to the original
factory settings.
1 Press
.
2 Select [Services] > [Reset], then press
3 Follow on-screen instructions.
Note
• You may recall the original PIN/passcode by
following this procedure.
UMS_M450/M455
01_EN_V1.0
.
.
> [Save number].
> [Delete].
.
> [Save number].
> [Delete].
to
on the base station for
to
Technical data
Battery
• Philips: 2 x AAA NiMH 1.2 V Rechargeable
550 mAh batteries
Use only the supplied batteries.
Adapter (Base and charger):
Meic:
Tenpao:
MN-A102-U130
S003IB0600040
Input:
100-240 V~
100-240 V~
50/60 Hz 200 mA
50/60 Hz 150 mA
Output:
6 V 400 mA
6 V 400 mA
Phonebook with 50 entries
Call log with 20 entries
Talk time: 16 hours
Standby time: 180 hoursRF output power: <24 dBm
Frequency Band: 1880 MHz ~ 1900 MHz
Note
•
prevent noise and caller ID problems caused by the
DSL interference.
•
www.p4c.philips.com.
Frequently
asked questions
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the base
station.
• If the handset displays [Unregistered], register
your handset (see the section on "Register additional
handsets").
If I fail to pair (register) the additional handsets to the
base station, what do I do?
Your base memory is full. Access
> [Services] >
[Unregister] to unregister the unused handsets and
try again.
I have chosen a wrong language which I cannot read,
what do I do?
1 Press
to go back to the standby screen.
2 Press
to access the main menu screen.
3 The following options will appear on the screen:
[Phone setup] > [Language]
[Réglages] > [Langue]
[Telefon-Setup] > [Sprache]
> [Lingua]
4 Select them to access the language options.
5 Select your own language.
My handset is in searching status, what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail, what do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your service
provider to change the settings.
No display
• Make sure the batteries are charged.
• Make sure there are power and phone connections.
The handset on the charger does not charge.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
once.
• Make sure the docking tone setting is turned on. When
the handset is placed correctly on the charger, you can
hear a docking tone.
• The charging contacts are dirty. Disconnect the power
• Batteries are defective. Purchase new ones with the
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer to
the base station.
• The phone receives interference from the nearby electrical
appliances. Move the base station away from them.
• The phone is at a location with thick walls. Move the
base away from them.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your service
provider.
• The caller's information is withheld or unavailable.
Advertisement
