Table of Contents
Advertisement
Available languages
Available languages
Quick Links
30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
United States
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
flammable vapors and liquids in the vicinity of this or any other appliance.
1. Clearances and Dimensions
a. Provide adequate clearances between the range and adjacent combustible surfaces.
b. Location—Check location where the range will be installed. Check for proper electrical supply and the stability of floor.
c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must
be solid and level.
FRONT
TYPICAL CABINET INSTALLATION
VIEW
* 30" minimum clearance between the top of the cooking surface
and the bottom of an unprotected wood or metal cabinet; or 24 "
minimum when bottom of wood or metal cabinet is protected by not
less than ¼" flame retardant millboard covered with not less than
no. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum
or 0.020" copper. The minimum clearance is 0" for the rear of the
range. Follow all dimension requirements provided above to prevent
property damage, potential fire hazard, and incorrect countertop
and cabinet cuts.
Avoid locating cabinet storage space above the surface units
to eliminate the possibility of cabinets catching on fire, or
personal burns from reaching for the cabinets over the heated
units. If cabinet storage is to be provided, risk can be reduced by
installing a range hood that projects horizontally a minimum of
5" beyond the bottom of the cabinets.
Important Notes to the Installer
1. Read all instructions contained in these installation instructions
before installing the appliance.
2. Remove all packing material before connecting the electrical
supply to the appliance.
3. Observe all governing codes and ordinances.
4. Be sure to leave these instructions with the consumer.
Important Note to the Consumer
Keep these instructions with your Use and Care Guide for future reference.
Printed in United States
FOR YOUR SAFETY: Do not store or use gasoline or other
1/8
FRONT
SIDE
VIEW
VIEW
1
All dimensions for
electrical outlet
location are maximum.
Cubed area shows
where the electrical
Terminal
outlet must be
Block
installed for the
Location
range to be flush to
the wall.
318201724 (0904) Rev. A
Canada
BACK
VIEW
Wall
Edge
Advertisement
Table of Contents
Related Manuals for Frigidaire 318201724
Summary of Contents for Frigidaire 318201724
-
Page 1: Clearances And Dimensions
Provide adequate clearances between the range and adjacent combustible surfaces. b. Location—Check location where the range will be installed. Check for proper electrical supply and the stability of floor. c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level. -
Page 2: Install Anti-Tip Bracket
For mobile homes, new installations or recreational vehicles, use only a power supply kit designed for a range at 125V/250V 50A recommended (minimum 40A). Cord must have either 3 (when local code permits grounding through neutral) or 4 conductors. -
Page 3: Three Conductor Wire Connection To Range
(see Figure 3): 1. Remove the screws from the access plate at the lower right end of the rear cover to expose range terminal connection block. 2. Using the nuts supplied in the literature package, connect... -
Page 4: Direct Electrical Connection To The Circuit Breaker, Fuse Box Or Junction Box
1. Be sure that no power is supplied on the cable from residence. 2. Follow instructions on previous page for Four Conductor Wire Connection to Range (Fig. 4). 3. In the circuit breaker, fuse box or junction box (Fig. 5): a) Connect the green (or bare copper) wire, the white appliance cable wire, and the neutral (white) wire together. -
Page 5: Anti-Tip Bracket Installation Instructions
Figure 8 6. Anti-Tip Bracket Installation Instructions IMPORTANT SAFETY WARNING To reduce the risk of tipping of the range, the range must be secured to the floor by properly installed anti- tip bracket and screws packed with the range. These parts are located in a plastic bag in the oven. - Page 6 30" ELECTRIC RANGE INSTALLATION INSTRUCTIONS NOTES...
- Page 7 POSTERIOR Todas las dimensiones para la ubicación del tomacorriente eléctrico son máximas. El aréa del cubo muestra donde se debe instalar Ubicación el tomacorriente del bloque eléctrico para terminal instalación a ras de la pared. 318201724 (0904) Rev. A Canadá...
- Page 8 INSTRUCCIONES PARA INSTALACION DE LA ESTUFA ELECTRICA DE 30” 2. Instale los soportes antivuelco. instrucciones en la página 4.) 3. Placa de Identificación Esta placa de identificación está localizada sobre el marco y se puede ver cuando la gaveta está abierta.
- Page 9 INSTRUCCIONES PARA INSTALACION DE LA ESTUFA ELECTRICA DE 30” Conexión del cable a tres alambres la cocina Si los códigos locales permiten la conexión del conductor a tierra del armazón al alambre neutral del cable de bronce del suministro eléctrico (vea figura 3). 1.
- Page 10 INSTRUCCIONES PARA INSTALACION DE LA ESTUFA ELECTRICA DE 30” Conexión eléctrica directa al cortacircuito, a la caja de fusibles o la caja de empalmes Si el aparato está conectado directamente al cortacircuito, a la caja de fusibles o a la caja de empalmes, use un cable blindado flexible o no metálico recubierto de cobre (con alambre a tierra).
-
Page 11: Antes De Llamar Al Servicio
INSTRUCCIONES PARA INSTALACION DE LA ESTUFA ELECTRICA DE 30” 5. Cómo nivelar la estufa Coloque una parilla del horno en el centro del horno. B. Ponga un nivel sobre la parrilla (Figura 7). Tome dos lecturas con el nivel puesto diagonalmente en una dirección y después en la otra. - Page 12 INSTRUCCIONES PARA INSTALACION DE LA ESTUFA ELECTRICA DE 30” NOTAS...