Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Epson ELPMB47
Summary of Contents for Epson ELPMB47
- Page 1 ELPMB26...
-
Page 2: Table Of Contents
Contents Included Items List ..................... 20 Safety Instructions ...................... 21 Precautions on Where to Mount the Projector ..........23 Installation ........................24 Removing the Ceiling Plate from the Projector Plate ..........24 Installing the Ceiling Plate to the Ceiling ..............25 Mounting to a Concrete Ceiling .................. -
Page 3: Included Items List
Included Items List Check the following list to confirm that you have all of the supplied items. If by any chance there is anything missing or damaged, please contact your dealer. Ceiling plate Projector plate The ceiling plate and projector plate are preassembled. Separate them before starting the installation. -
Page 4: Safety Instructions
Safety Instructions Read this document carefully to assemble and install this product safely and correctly. Be sure to follow the safety precautions. Keep these instructions close to hand to help solve any points you do not understand. So that you can use the product safely and correctly, symbols are applied in this guide and on the product to indicate possible harm to the user or to others and the risk of damage to property. - Page 5 Warning v Always follow the instructions below when installing the ceiling mount. If installation work is not carried out correctly, the projector and ceiling mount could fall and cause injury. • Check the structure and materials of the mounting location and use the most appropriate construction method.
-
Page 6: Precautions On Where To Mount The Projector
Caution At least two people are needed for the installation. Make sure to provide a sturdy scaffold for this work. Otherwise, you may fall or drop the projector and cause injury. Precautions on Where to Mount the Projector Carefully read the warnings in "Safety Instructions / Support and Service Guide" supplied with your projector before starting the installation to determine a suitable place to install it. -
Page 7: Installation
Installation Removing the Ceiling Plate from the Projector Plate The ceiling plate is fitted to the projector plate at the factory. Use the following procedure to separate them. Procedure Remove the screws for the vertical tilt adjustment points on both sides using the supplied M8 hexagon wrench. -
Page 8: Installing The Ceiling Plate To The Ceiling
Installing the Ceiling Plate to the Ceiling Determine the distance to the screen and locate the mounting position before mounting the ceiling plate. The distance varies according to the type of the lens unit installed on the projector. See the "User's Guide"... -
Page 9: Mounting To A Concrete Ceiling
Tighten the screws firmly during installation or after adjusting the angles. After tightening the screws, retighten them firmly and make sure that they are not loose. v Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation. -
Page 10: Fitting The Projector Plate To The Projector
Fitting the Projector Plate to the Projector Warning v Tighten the screws firmly. After tightening the screws, retighten them firmly and make sure that they are not loose. v Install the supplied safety wire to prevent the projector from falling. sp.31 v Applying a screw-locking adhesive, lubricant, oil or other substance to the points at which the projector is fixed to the ceiling mount can make the case crack and the projector fall, leading to damage or injury. -
Page 11: Fitting The Projector Plate To The Ceiling Plate
Fitting the Projector Plate to the Ceiling Plate Procedure Put the shaft of the projector plate into the grooves of the ceiling plate and place it securely in the horseshoe-shaped points. Do not release your hands from the projector until mounting is complete. Put the screws for the vertical angle adjustment points that were removed when removing the ceiling plate from the projector... -
Page 12: Adjusting The Installation Position
Adjusting the Installation Position Warning v Never loosen or remove any screws needlessly when adjusting the position. Doing so could cause the projector to fall and lead to an accident. v Retighten all screws and make sure that they are not loose after adjustment. Moving the Projected Images Higher or Lower When the images are projected higher or lower compared to the screen, adjust the projection position using the lens shift of the projector. -
Page 13: Tilting The Projected Images To The Right Or Left
Tilting the Projected Images to the Right or Left When the projected image is tilted to the right or left compared to the screen, tilt the projector ±5 degrees to adjust the projection position. Procedure Loosen the four screws for the horizontal roll adjustment points at the front and rear using the supplied M8 hexagon wrench. -
Page 14: Installing The Safety Wires
Installing the Safety Wires After installing the projector on the ceiling, take additional precautions to secure it in place and prevent it from falling or rolling. Pass the wires provided diagonally through the projector plate using the wire clips to prevent the projector from falling. - Page 15 Wire clip Loosen the screws of the wire clip, and then pass the end of the safety wire through the wire clip and a hole on the projector plate. Pull the end of the wire rope out from under the projector plate and pass it through the wire clip.
-
Page 16: Inquiries
Inquiries Inquiries can be directed to the contact information given in the manual of the projector. Specifications Dimensions 400 (W) x 124 (H) x 330 (D) mm Weight Approx. 11 kg Maximum load capacity Approx. 75 kg Adjustable range Vertical tilt adjustment 0 to ±5°...