Related Manuals for Toro Bullseye QuickGroom 710
Summary of Contents for Toro Bullseye QuickGroom 710
- Page 1 Form No. 3449-177 Rev A Operator's Manual QuickGroom 710 Model No. 46405AA—Serial No. 321000001 and Up Model No. 46405BA—Serial No. 321000001 and Up *3449-177* Register at www.Toro.com/bullseye. Original Instructions (EN)
-
Page 2: Table Of Contents
Figure 1 Preparing the Machine for Storage ....12 Troubleshooting ............13 1. Model and serial number location © 2021—The Toro® Company Contact us at www.Toro.com/bullseye. 8111 Lyndale Avenue South Printed in the USA Bloomington, MN 55420 All Rights Reserved... -
Page 3: Safety
Safety and Instructional Safety Decals General Safety Safety decals and instructions are easily visible to the operator and are This product is capable of causing personal injury. located near any area of potential Always follow all safety instructions to avoid serious danger. -
Page 4: Setup
Setup Place the pallet on level ground. Attach lifting cables to the crossbar and pallet. Removing the Machine from the Pallet No Parts Required Procedure The machine is shipped vertically on the pallet. Use the following instructions to remove it from the pallet. DANGER The attachment is unstable and could swing when lifted, injuring anyone beneath it or... -
Page 5: Installing The Operator's Manual Tube
g367256 Figure 4 1. 3-point hitch pins (3) Installing the Operator’s Manual Tube Parts needed for this procedure: Operator’s Manual tube Plate Bolt (M8) Washer Locknut (M8) Procedure Cut the cable ties securing the Operator’s Manual tube to the attachment. Remove the cap from the tube. -
Page 6: Inspecting The Machine
Contact your Checking the Ballast Authorized Service Dealer or authorized Bullseye distributor or go to www.Toro.com/Bullseye for a list of Requirements all approved attachments and accessories. WARNING... -
Page 7: Before Operation
Connecting to a 3-Point Operation Hitch Before Operation Connecting the Lower Link Arms Before Operation Safety Ensure that the attachment is positioned on a level surface. • Never allow children or untrained people to Remove the hairpin cotters and hitch pins from operate or service the machine. - Page 8 Connecting the Upper Link Connect the upper link to the lower hole in the bracket frame secure it with the link pin and the hairpin cotter. g345394 Figure 7 2. Hitch pin and hairpin cotter 1. Lower link arm (2) g345396 Figure 8 1.
-
Page 9: Transporting The Attachment
Transporting the • Never leave a running machine unattended. • Before leaving the operating position, do the Attachment following: To begin transport operation, raise the machine. To – Park the machine on a level surface. avoid loss of control, traverse steep inclines slowly, –... -
Page 10: Operating The Attachment
Operating Tips or the edge caves in. Establish a safety area between the machine and any hazard. • Make very gradual turns. Never make sharp turns • Identify hazards at the base of the slope. If with the attachment. there are hazards, mow the slope with a power •... -
Page 11: Removing The Attachment
Removing the Attachment Important: Ensure that the attachment does not slide off the traction unit and cannot roll Park the machine on a level surface, engage the away. parking brake, shut off the engine, and remove the key from the traction unit. Lower the 4 storage legs. -
Page 12: Storage
Storage Storage Safety • Before adjusting, cleaning, storing, or repairing the machine, park the it on a level surface; engage the parking brake of the traction unit; shut off the engine; remove the key; and wait for all movement to stop before leaving the traction unit. •... -
Page 13: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The attachment loosened too little 1. The working depth is set too shallow. 1. Increase the working depth. material. 2. The infill material is too compacted. 2. Drive multiple passes over the turf, each with a deeper setting. The appearance of the field is poor. - Page 14 Notes:...
- Page 15 California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
- Page 16 Warranty Statement One-Year Limited Warranty Conditions and Products Covered Parts Your Bullseye product (“Product”) is warranted to be free from defects in Parts scheduled for replacement, as required maintenance, are covered for materials or workmanship for 1 year. Where a warrantable condition exists, the same warranty period as the product warranty.