Hitachi L300P Series Service Manual page 15

Function Mode
Code Function name
s t
A061 1 frequency upper limiter
nd
A261 2 frequency upper limiter
s t
A062 1 frequency lower limiter
nd
A262 2 frequency lower limiter
A063 Jump frequency1
A064 Jump frequency Width 1
A065 Jump frequency2
A066 Jump frequency Width 2
A067 Jump frequency3
A068 Jump frequency Width 3
A069 Acceleration stop frequency
A070 Acceleration stop time
A071 PID selection
A072 PID-P gain
A073 PID-I gain
A074 PID-D gain
A075 PID scale
A076 PID feedback selection
A081 AVR selection
A082 Motor voltage selection
A085 Operation mode selection
Energy-saving response-
A086
accuracy adjustment
A092 Acceleration time2
nd
A292 2 acceleration time2
A093 Deceleration time2
nd
A293 2 deceleration time2
nd
A094 2 stage adjustable selection
nd
2 stage adjustable
A294
nd
selection(2 motor)
nd
A095 2 acceleration frequency
nd
2 acceleration
A295
nd
frequency(2 motor)
nd
A096 2 deceleration frequency
nd
2 deceleration frequency
A296
nd
(2 motor)
A097 Acceleration pattern selection
A098 Deceleration pattern selection
A101 OI start
A102 OI end
A103 OI start rate
A104 OI end rate
A105 OI start selection
A111 O2 start
A112 O2 end
A113 O2 start rate
A114 O2 end rate
A131 Acceleration curve constant
A132 Deceleration curve constant
b001 Retry selection
Allowable under-voltage
b002
power failure time
b003 Retry wait time
Instantaneous power-
b004 failure/under-voltage trip
during stop
Instantaneous power-
b005 failure/under-voltage
retry time selection
b006 Open-phase selection
b007 Frequency setting to match
b012 Electronic thermal level
Electronic thermal level
b212
nd
(2 motor)
Electronic thermal
b013
characteristic selection
Electronic thermal
b213 characteristic selection
nd
(2 motor)
Free electronic thermal
b015
frequency 1
Free electronic thermal
b016
current 1
Free electronic thermal
b017
frequency 2
Free electronic thermal
b018
current 2
Free electronic thermal
b019
frequency 3
Free electronic thermal
b020
current 3
L300P Setting range
s t
0.00, 1 frequency lower limiter-maximum frequency(Hz)
nd
0.00, 2 frequency lower limiter-2
frequency(Hz)
0.00, start frequency-maximum frequency(Hz)
nd
0.00, start frequency-2 setting maximum frequency(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-10.00(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-10.00(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-10.00(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-60.0(s)
00(invalid)/01(valid)
0.2-5.0
0.0-3600.(s)
0.00-100.0(s)
0.01-99.99
00(feedback : OI)/01(feedback : O)
00(ON always)/01(OFF always)/02(OFF on decelerating)
200/215/220/230/240, 380/400/415/440/460/480
00(normal operation)/01(energy-saving operation)
0.0-100.0
0.01-99.99/100.0-999.9/1000.-3600.(s)
0.01-99.99/100.0-999.9/1000.-3600.(s)
0.01-99.99/100.0-999.9/1000.-3600.(s)
0.01-99.99/100.0-999.9/1000.-3600.(s)
00(change with 2CH terminal)/01(change with setting)
00(change with 2CH terminal)/01(change with setting)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
00(straight line)/01(S-curve)/02(U-curve)/03(reverse U-curve)
00(straight line)/01(S-curve)/02(U-curve)/03(reverse U-curve)
0.00-99.99/100.0-400.0(Hz)
0.00-99.99/100.0-400.0(Hz)
0.-100. ( %)
0.-100. ( %)
00(external start frequency)/01(0Hz)
-400.--100./-99.9-0.00-99.9/100.-400.(Hz)
-400.--100./-99.9-0.00-99.9/100.-400.(Hz)
-100. - 100. (%)
-100. - 100. (%)
01(small swelling)-10(large swelling)
01(small swelling-10(large swelling)
00(trip)/01(0Hz start)/02(start after equal frequency)/
03(trip after equaling frequency and deceleration stop)
0.3-1.0(s)
0.3-100.(s)
00(invalid/01(valid)/
02(invalid during stop and deceleration by stop command)
00(16 times)/01(free)
00(invalid)/01(valid)
0.00-99.99/100.0-400.0(Hz)
0.2*constant current-1.20*constant current(A)
0.2*constant current-1.20*constant current(A)
00/(reduced characteristic)01(constant torque characteristic)/
02(free setting)
00/(reduced characteristic)01(constant torque characteristic)/
02(free setting)
0.-400.(Hz)
0.0-1000.(A)
0.-400.(Hz)
0.0-1000. (A)
0.-400.(Hz)
0.0-1000.(A)
1- 12
Initial data
-FE/-FU/-FR
nd
setting maximum
00/00/02
(230/400)
(230/460)
(200/400)
Rated
Current of
inverter
Rated
Current of
inverter
01/01/00
01/01/00
N o t e
0.00
0.00
0.00
0.00
0.00
0.50
0.00
0.50
0.00
0.50
0.00
0.0
00
1.0
1.0
0.00
1.00
00
00
50.0
15.00
15.00
15.00
15.00
00
00
0.00
0.00
0.00
0.00
00
00
0.00
0.00
20.
100.
01
0.00
0.00
-100.
100.
02
02
00
1.0
1.0
00
00
00
0.00
0.
0.0
0.
0.0
0.
0.0