Page 1
INSTRUCTION MANUAL | MANUAL DE INSTRUCTIONES 6 in. (150 mm) Bench Grinder Amoladora de banco de 150 mm (6 pulgadas) CMXEGAR500 IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US. SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS. 1-888-398-7737 WWW.CRAFTSMAN.COM...
Page 2
English (original instructions) Español (traducido de las instrucciones originales)
Damage or personal injury could result. Left tool rest assembly WARNING: To reduce the risk of injury, read the Coarse grinding wheel (36 Grit) instruction manual. Spark guards if you have any questions or comments about this Eye shield product, call CRAFTsMAn toll free at: 1-888-398-7737.
English 6 in. (150 mm) Bench Grinder CMXEGAR500 GENERAL POWER TOOL SAFETY WARNINGS 3) Personal Safety a ) Stay alert, watch what you are doing and use WARNING: Read all safety warnings, common sense when operating a power tool. Do...
English • Always inspect grinding wheels prior to use for cracks, d) Store idle power tools out of the reach of children missing pieces, etc. Replace wheel immediately before use. and do not allow persons unfamiliar with the power tool or these instructions to operate the •...
English • ALWAYS EASE THE WORKPIECE AGAINST THE READ INSTRUCTION MANUAL: To reduce the risk of injury, user and all bystanders must read instruction ABRASIVE WHEEL when starting to grind. A harsh manual before using this product. impact can break the wheel. Use light pressure when starting to grind.
Page 7
English IMPROPER CONNECTION of the equipment grounding (Fig. C) can be used to temporarily connect this plug to a two- conductor can result in risk of electric shock. The conductor contact grounded receptacle. The adapter (Fig. C) has a rigid with the green insulation (with or without yellow stripes) is lug extending from it that MUST be connected to a permanent the equipment grounding conductor.
English Motor UNPACKING YOUR BENCH GRINDER Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than 10% will cause loss of power and overheating. These tools are factory tested; if this tool does not operate, check power supply. TOOLS NEEDED FOR ASSEMBLY not supplied Phillips Screwdriver...
English ASSEMBLY AND ADJUSTMENTS 4. Repeat the above steps for installing the other LED light and eye shield assembly. Estimated Assembly Time: nOTE: Adjust eye shidlds to appropriate distance from 10 - 20 Minutes. tool rests avoiding interference when operation. WARNING: To avoid injury, do not connect Fig. E this bench grinder to the power source until...
Page 10
English when turning toward the rear of the grinder and loosen Fig. I loosen when turning toward the front of the grinder. 6. Remove the hex nut , the outside wheel flange and the wheel 7. Inspect the wheel for cracks, chips or any other visible damage (other than normal wear) and discard if such damage is found.
English Fig. L OPERATION Starting And Stopping The Grinder (Fig. N) WARNING: To avoid injury, always keep the plug disconnected from the power source and switch turned OFF until the grinder is completely assembled and adjusted properly. The ON/OFF switch is located on the front of the grinder. To turn the grinder on, press the switch to the "I"...
Page 12
English Lawn Mower Blades 7. Never sharpen or grind anything made of aluminum, brass, copper, wood, plastic or any other non-metallic Lawn mower blades are usually sharpened on only one side materials. and dressed up slightly on the other. After sharpening, be sure to balance the blade by removing additional material WARNING: Grind only on the face of the grinding from the heavy end.
English Free Warning Label Replacement: MAINTENANCE If your warning labels become illegible or are missing, call WARNING: For your own safety, turn switch "OFF" 1-888-398-7737 for a free replacement. and remove plug from power soure outlet before adjusting and maintaining your bench grinder. If power cord is worn, cut or damaged in any way, have it replaced immediately.
TROUBLESHOOTING GUIDE BE sURE TO FOllOW sAFETY RUlEs AnD insTRUCTiOns For assistance with your product, visit our website at www.craftsman.com for a list of service centers, or call CRAFTSMAN at 1-888-398-7737. PlEAsE READ ThE FOllOWing: The manufacturer and/or distributor is providing the buyer with a parts list and assembly diagram in this manual as a reference tool only.
90 DAY MOnEY BACK gUARAnTEE If you are not completely satisfied with the performance of your CRAFTSMAN Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.
English PARTS LIST 6 in. (150 mm) Bench grinder Parts list for bench grinder i.D.nO. Description size Q’ty X70D BATTERY COVER X70E AAA BATTERY X70F LED ASS’Y X70G SMALL CARRIAGE BOLT M5*60 X70H LAMP COVER X70J PHILIPS SCREW ST2.9*8 X70K BUSHING X70L RUBBER FOOT...
Page 17
English 6 in. (150 mm) Bench grinder schematic for bench grinder...