Page 1 LINE Digital Super Hybrid System Programming Guide KX-TD500 Model No. Please read this manual before connecting the Digital Super Hybrid System and save this manual for future reference. Thank you for purchasing the Panasonic Model KX-TD500, Digital Super Hybrid System.
Page 2 Introduction Introduction This Programming Guide is designed to serve as a technical reference for the Panasonic Digital Super Hybrid System, KX-TD500. It provides step-by-step instructions for performing system programming using the Maintenance Console software for a PC. About the Other Manuals...
Page 3: Table Of Contents
Table of Contents Table of Contents 1 Configuration..................5 1.1 Configuration........................6 1.2 Slot Assignment ......................7 1.3 Trunk Port Assignment....................52 1.4 Extension Port Assignment..................54 1.5 VPS (DPT) Port Assignment ..................59 1.6 T1 Port Assignment......................65 1.7 DISA Port Assignment ....................68 1.8 BRI Port Assignment ....................69 1.9 PRI Port Assignment....................72 2 System....................75 2.1 System..........................76...
Page 4 Table of Contents 5.7 Special Carrier Code ....................260 5.8 Absent Message......................261 5.9 DISA/TIE User Code....................262 5.10 VPS Integration ....................... 264 5.11 Caller ID Modification .................... 273 5.12 Caller ID Registration ..................... 276 5.13 UCD Time Table ...................... 279 6 Toll Restriction ................
Page 5: Configuration
Configuration Section 1 Configuration Programming Guide...
Page 6: Configuration
Configuration 1.1 Configuration Used to determine the basic system configuration. Programming Guide...
Page 7: Slot Assignment
Configuration 1.2 Slot Assignment Card Properties Guide Card Properties screen lists and lets you customize the operating characteristics associated with a certain optional card. The following optional cards have Card Properties screens: Extension Cards; HLC, SLC, OPX, SLC-M, DHLC, ESLC, DLC Trunk Cards;...
Page 8 Configuration 2. Point to , and click. • "Card Properties" screen is displayed. 3. After editing the parameters, click • "Card Properties" screen is closed and "Writing" is displayed while the data changes are being saved. Copy Function When multiple numbers of the same type optional cards are installed in the system, Card Properties data of one card can be copied to those of all other same type optional cards at a time.
Page 9 Configuration Properties Copy 3. Point to , and click. • "Card Properties Copy" screen is displayed. 4. Point to , and click. • All displayed Slot Nos. will be highlighted. • You can specify a certain Slot No. individually by clicking it directly. Programming Guide...
Page 10 Configuration 5. Point to , and click. • "Are you sure?" is displayed. 6. Point to , and click. • "Executing" is displayed while the source data is being copied to the destination. 1.2.1 Slot Assignment Assigns the type of service cards, inserted in the free slots in the basic and expansion shelves. Section "1.2 Slot Assignment"...
Page 11 Configuration 1.2.14 CPU Card Information 1.2.15 TSW Card Configuration Programming Guide...
Page 12 Configuration Parameter Card Type Default Blank Value Range Please refer to "Description/Function." Description/Function Specifies the type of service cards inserted in the free slots in the basic and expansion shelves. <Selection> None: Not assigned. AGC: Automatic Gain Control card BRI: ISDN Basic Rate Access Interface card DHLC: Digital Hybrid Line Circuit card DID: Direct Inward Dialing Trunk card DISA: Direct Inward System Access card...
Page 13 Configuration Parameter Status Default — Value Range FAULT Description/Function Used to set the status of the service cards. INS (In-Service): The target service card is operating normally. OUS (Out-of-Service): Programming data for the target service card is entered, but the target service card is not assigned to the system.
Page 14 Configuration Parameter % Break Detection Default 16-96 ms Value Range 16-96 ms 16-136 ms Description/Function Specifies the Pulse Break Detection length. Dialed digits from a dial pulse type SLT are transmitted to the system by making and breaking a loop current, thereby interrupting loop current.
Page 15 Configuration Parameter % Break Detection Default 16-96 ms Value Range 16-96 ms 16-136 ms Description/Function Specifies the Pulse Break Detection length. Dialed digits from a dial pulse type SLT are transmitted to the system by making and breaking a loop current, thereby interrupting loop current.
Page 16 Configuration Parameter Off-hook Time Default 160 ms Value Range 8-512 ms in 8 ms increments Description/Function Specifies the length of time in milliseconds that the system recognizes as an off-hook signal sent from the local Central Office. (Assignable for DHLC and ESLC only.) Reference None Parameter...
Page 17 Configuration Parameter First Dial Timer Default 1.0 s Value Range 0.5-8.0 s in 0.5 s increments Description/Function On outgoing CO calls, the system waits at least 1.0 second after seizing the CO line, before sending the dialing digits to the Central Office by default.
Page 18 Configuration Parameter Inter-digit Pause Default 830 ms Value Range 630 ms 830 ms 1030 ms Description/Function Used to distinguish between pulse signals. To meet the requirements of your Central Office, select the appropriate value that represents the delay between dial pulses. (This setting is only required when using dial pulse trunks.) Reference None...
Page 19 Configuration Parameter First Dial Timer Default 1.0 s Value Range 0.5-8.0 s in 0.5 s increments Description/Function On outgoing CO calls, the system waits at least 1.0 second after seizing the CO line, before sending the dialing digits to the Central Office by default.
Page 20 Configuration Parameter Pulse Feedback Tone Default Value Range Description/Function On outgoing CO calls, the dialed number is toned out, which informs the extension user that dialed number has been dialed out. The dialed number is toned out by default. Select "No" to turn off the pulse feedback tone.
Page 21 Configuration Parameter Bell Detection Time Default 144 ms Value Range 24-1200 ms in 24 ms increments Description/Function Specifies the length of time in milliseconds the system requires to determine that the received signal is the bell signal. Reference None Parameter DTMF Inter-digit Pause Time Default 112 ms...
Page 22 Configuration 1.2.6 Card Properties (ELCOT) – Caller ID Used to set the parameters for the Caller ID card. Parameter Caller ID Detection Default Check Value Range Check No check Description/Function Activates or deactivates the detection of Caller ID signals transmitted from the Central Office on a port basis. Reference •...
Page 23 Configuration Parameter Carrier Detection Default Disable Value Range Enable Disable Description/Function Activates or deactivates the detection of carrier signal before receiving Caller ID signal. Reference • 1.5 Attended Features (F/G) – Caller ID Service Parameter Detection Time Default 2000 ms Value Range 1040-4000 ms in 80 ms increments Description/Function...
Page 24 Configuration 1.2.7 Card Properties (T1) Used to set the parameters for the T1 card. When you change the card properties, the card status must be "OUS (Out-of-Service)." Parameter Line Coding Default B8ZS Value Range B8ZS Description/Function Specifies the T1 PCM (Pulse Code Modulation) Line Coding type for each T1 card.
Page 25 Configuration Parameter ESF Frame Option Default C = A, D = B Value Range C = A, D = B C = 0, D = 0 C = 1, D = 0 C = 0, D = 1 C = 1, D = 1 Description/Function Defines the values of C-bit and D-bit.
Page 26 Configuration Parameter First Dial Timer (DID / TIE) Default 64 ms Value Range 32-8160 ms in 32 ms increments Description/Function On outgoing DID / TIE line calls, the system waits at least 64 milliseconds after seizing the trunk line, before sending the dialing digits to the Central Office / other PBX by default.
Page 27 Configuration Parameter Signaling Bit Monitor (Port No.) Default Disable Value Range Disable Port No. 1-24 Description/Function Specifies the port to monitor the signaling bit using the LED on the T1 card. Note • This setting is valid when the LPR software version of the T1 card is "Y311D"...
Page 28 Configuration Parameter Inter-digit Pause Default 830 ms Value Range 630 ms 830 ms 1030 ms Description/Function Used to distinguish between pulse signals. To meet the requirements of other PBX or Central Office, select the appropriate value that represents the delay between dial pulses. (This setting is only required when using dial pulse trunks.) Reference •...
Page 29 Configuration Parameter Answer Decision Timer Default 32 ms Value Range 32-8160 ms in 32 ms increments Description/Function Specifies the time range in milliseconds that the system requires to recognize the answer signal. Reference • 1.3 System Features (F/G) – T1 Carrier Parameter % Break Detection Default...
Page 30 Configuration 1.2.8 Card Properties (BRI) Used to assign the parameters for the BRI (Basic Rate Interface) card. When you change the card properties, the card status must be "OUS (Out-of-Service)." Parameter Network Type Default (Display only) Value Range National ISDN1(fixed) Description/Function Displays the ISDN type.
Page 31 Configuration Parameter Status Message Default Enable Value Range Enable Disable Description/Function Specifies whether to send the Status Message to ISDN or not. Reference None Parameter Status Receive Default Disconnect Value Range Disconnect Ignore Description/Function Specifies the treatment of the call when the Status Message provided by ISDN doesn't match the actual status of the call.
Page 32 Configuration Parameter [Line Mode] TEI Default (Display only) Value Range Automatic (fixed) Description/Function Displays the TEI (Terminal Endpoint Identifier) mode on an ISDN line basis. Reference None Parameter [Line Mode] TE Power Default No check [Disable] Value Range Check [Enable] No check [Disable] Description/Function Specifies whether the system supplies an electric power to TE or...
Page 33 Configuration Parameter Software Information Default (Display only) Value Range — Description/Function Displays the ROM version of the BRI card software and ROM checksum. Reference None 1.2.9 Card Properties (BRI) – SPID/DN Used to assign the SPID and the DN on an ISDN BRI port basis. You can get these information from the ISDN provider.
Page 34 Configuration Parameter SPID Default Blank Value Range Up to 20 digits consisting of 0-9, , # or P (Pause) Description/Function Specifies an SPID on an ISDN BRI port basis. Reference None Parameter Default Blank Value Range Up to 20 digits consisting of 0-9, , # or P (Pause) Description/Function Specifies a DN on an ISDN BRI port basis.
Page 35 Configuration Parameter Network Type Default (Display only) Value Range National ISDN1(fixed) Description/Function Displays the ISDN type. Reference None Parameter Status Message Default Enable Value Range Enable Disable Description/Function Specifies whether to send the Status Message to ISDN or not. Reference None Parameter Status Receive...
Page 36 Configuration Parameter Line Coding Default B8ZS Value Range B8ZS Description/Function Specifies the PCM (Pulse Code Modulation) Line Coding type for the PRI23 card. Reference None Parameter Frame Sequence Default Extended Superframe (ESF) Value Range 4-Frame Multiframe (F4) 12-Frame Multiframe (F12) Extended Superframe (ESF) Remote Switch (F72, SLC96) Description/Function...
Page 37 Configuration Parameter Timer Setting Default — Value Range — Description/Function You can enter into "ISDN Protocol Timer" screen (Section "1.2.11 Card Properties (BRI/PRI23) – ISDN Protocol Timer") by clicking Timer Setting on this screen. Reference None 1.2.11 Card Properties (BRI/PRI23) – ISDN Protocol Timer ISDN protocol timers are defined by the ISDN user interface protocols.
Page 38 Configuration Parameter Default 35 s Value Range 0-60 s Description/Function Trunk port: Specifies the maximum time allowed to the system after receiving the notification of call disconnection from ISDN, before replying to Reference None Parameter Default 10 s Value Range 0-60 s Description/Function Trunk port:...
Page 39 Configuration Parameter Default 35 s Value Range 0-60 s Description/Function Extension port: Specifies the maximum time allowed to the system after receiving the notification of call disconnection from ISDN, before replying to Reference None Parameter Default 10 s Value Range 0-60 s Description/Function Extension port:...
Page 40 Configuration Parameter [CO/Qsig-Master(PRI only)/Qsig-Slave(PRI only)] T302 Default 10 s (BRI), 15 s (PRI23) Value Range 2-30 s Description/Function Specifies the maximum time allowed between each digit on an incoming call. Applies to the overlap receiving. Reference None Parameter [CO/Qsig-Master(PRI only)/Qsig-Slave(PRI only)] T303 Default 5 s (BRI), 4 s (PRI23) Value Range...
Page 41 Configuration Parameter [CO/Qsig-Master(PRI only)/Qsig-Slave(PRI only)] T306 Default 30 s (BRI), 0 s (PRI23) Value Range 0-255 s Description/Function Reserved for future use. Reference None Parameter [CO/Qsig-Master(PRI only)/Qsig-Slave(PRI only)] T310 Default 0 s (BRI), 30 s (PRI23) Value Range 10-300 s Description/Function Specifies the maximum time that the system waits after receiving the Incoming Call Proceeding (call setting acceptance) message,...
Page 42 Configuration Parameter [Extension] T203 Default 10 s Value Range 1-60 s Description/Function Specifies the time to detect no communication status of L2. Reference None Parameter [Extension] T302 Default 10 s (BRI), 15 s (PRI23) Value Range 2-30 s Description/Function Specifies the maximum time allowed between each digit on an incoming call.
Page 43 Configuration Parameter [Extension] T305 Default 30 s (BRI), 4 s (PRI23) Value Range 4-30 s Description/Function Specifies the maximum time that the system waits after sending the DISC (disconnection) message to ISDN, before receiving the reply to it. Reference None Parameter [Extension] T306 Default...
Page 44 Configuration Parameter [Extension] T3D9 Default 0 s (BRI), 20 s (PRI23) Value Range 0-255 s Description/Function Specifies the time that the system tries to disconnect L2 in "Call- by-Call mode." Reference None 1.2.12 Card Properties (DISA) Used to set the parameters for the DISA card. Parameter CYCLIC Tone Detection Mode Default...
Page 45 Configuration Parameter Decision Count Default 4 times Value Range 4-7 times Description/Function Specifies the number of times the tone pattern must be received to establish reception of the CYCLIC tone. This determines end-of- call. Note • This parameter is valid when "Option" is selected in the "CYCLIC Detection Mode"...
Page 46 Configuration Parameter [Tone-OFF Time] Min. Default 144.0 ms Value Range 57.6-3600 ms in 14.4 ms increments Description/Function Specifies the minimum time in milliseconds that the CYCLIC tone from the Central Office is not detected. When the system detects no tone within the time range, it is recognized as "Tone-OFF." Note •...
Page 47 Configuration 1.2.13 Card Properties (ERMT) Used to set the parameters for the ERMT card. Parameter Baud Rate (Modem Speed) Default 33600 bps Value Range 1200 bps 9600 bps 14400 bps 19200 bps 28800 bps 33600 bps Description/Function Specifies the maximum data transmission speed between the ERMT card and the modem which is connected to a Personal Computer (= Maintenance Device).
Page 48 Configuration Parameter Software Version Default (Display only) Value Range — Description/Function Displays the System ROM version. Reference None Parameter Area Code Default (Display only) Value Range 0-31 Description/Function Indicates the jumper setting on the CPU card, thereby revealing what area (country) the system is intended for. Reference None 1.2.15 TSW Card Configuration...
Page 49 Configuration Parameter [Option Card Status] Conference Expansion Card Default (Display only) Value Range Not Installed Installed Description/Function Displays whether an optional Conference Expansion Card is installed or not. Reference • 1.12 Conversation Features (F/G) – Conference, 3-Party – Conference, 5-Party –...
Page 50 Configuration Parameter Clock Configuration Mode Default External Value Range Internal External Description/Function Specifies the system clock mode to "Internal" or "External." Internal: The system synchronizes to a clock pulse provided by the internal clock on the TSW card. External: The system synchronizes to a clock pulse provided by the Digital Network.
Page 51 Configuration Parameter Clock Configuration Priority 1 - 8 Default None or 101-314: T1 / BRI / PRI23 Value Range None, 101-314: T1 / BRI / PRI23 Description/Function Specifies the physical number of the T1 / BRI / PRI23 card that provides External Clock pulse to the system in priority order.
Page 52: Trunk Port Assignment
Configuration 1.3 Trunk Port Assignment Used to assign each trunk port in the system to one of up to 48 trunk groups. Parameter Card No. Default — Value Range XXX: YYY [XXX: Card No. (101-314), YYY: Card Type] Description/Function Specifies the physical number of the trunk card and its type, which you are going to program.
Page 53 Configuration Parameter Status Default — Value Range FAULT Description/Function Specifies the operating status of the trunk port. INS: The trunk port is In-Service. OUS: The trunk port is Out-of-Service. FAULT: The trunk port is defective. Reference None Programming Guide...
Page 54: Extension Port Assignment
Configuration 1.4 Extension Port Assignment Used to set various parameters for extension ports. XDP extensions are on ports 9 through 16 of a DHLC card. Parameter Card No. Default — Value Range XXX: YYY [XXX: Card No. (101-314), YYY: Card Type] Description/Function Specifies the physical number of the extension card and its type, which you are going to program.
Page 55 DSS: Select this option when you connect a DSS Console to the extension port. VPS (DPT): Select this option when a port of Panasonic Voice Processing System (one that supports DPT Integration) is connected to the extension port. Notes • "DPT integration (except TVS300)" does not function unless the VPS is connected to a DLC or DHLC card whose LPR Version (ROM Version) is 1 or later.
Page 56 Configuration Parameter Tel. Type Default (Display only) Value Range Please refer to "Description / Function." Description/Function Displays the model number of telephone set which is currently connected to the extension port. <Telephone type list> Unknown: Not connected or Single Line Telephone T7130: APT with SP-PHONE, 1-Line Display (12-CO) T7020: APT with SP-PHONE (12-CO) T7030: APT with SP-PHONE, 1-Line Display (12-CO)
Page 57 Configuration Parameter Default 1001 – Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the DN (Directory Number = extension number) for the extension port. Note • You must assign the paired extension for DN after selecting DSS for the attribute. Reference •...
Page 58 Configuration Parameter Parallel / XDP (HLC card) Default None Value Range None Parallel Description/Function Specifies whether to enable or disable "Paralleled Connection of PT and SLT." Reference • 1.3 System Features (F/G) – Paralleled Telephone Parameter Status Default — Value Range FAULT Description/Function Specifies the operating status of the extension port.
Page 59: Vps (Dpt) Port Assignment
Configuration 1.5 VPS (DPT) Port Assignment Used to assign parameters for VPS (DPT) ports. Up to eight Panasonic Voice Processing Systems (VPSs) can be connected to the system. How to set up a TVS 1. Assignment of the card which will be connected to the VPS System.
Page 60 Parameter TVS No. Default Value Range 1- 8 Description/Function Specifies one of the Panasonic Voice Processing Systems (VPSs) connected to the KX-TD500 system, which you are going to program. Reference • 1.3 System Features (F/G) – Integration, VPS • 1.2 Slot Assignment (P/G)
Page 61 TVS200 TVS80/110/200-1/200-2 TVS300 Description/Function Specifies the model number of the Panasonic Voice Processing System which will be connected to the VPS card. Note • Please select "TVS200-1," if HDD (Hard Disk) Software Version of your TVS200 is 2.00 or later.
Page 62 Configuration Parameter [Ext No.1] DN Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the extension for B1 channel. Notes • This program allows you to assign an extension number to each Voice Mail port. Since each port connected to the VPS provides two extensions, this enables you to assign extension numbers to each port.
Page 63 Configuration Parameter [Ext No.2] DN Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the extension for B2 channel. Notes • This program allows you to assign an extension number to each Voice Mail port. Since each port connected to the VPS provides two extensions, this enables you to assign extension numbers to each port.
Page 64 Configuration Parameter DN Refer Default — Value Range — Description/Function Displays the list of DNs/FDNs which are already assigned to the extensions / system resources. Reference None Programming Guide...
Page 65: T1 Port Assignment
Configuration 1.6 T1 Port Assignment Used to assign parameters for T1 ports. How to set up a T1 card 1. Insert T1 card into a free slot. Notes • T1 card should be installed in the free slot no. 1, 5 or 9 of each shelf. •...
Page 66 Configuration Parameter Card No. Default — Value Range XXX : T1 [ XXX : Card No. (101-314)] Description/Function Specifies the physical number of the T1 digital trunk card which you are going to program. Reference • 1.2 Slot Assignment (P/G) Parameter Channel Type Default...
Page 67 Configuration Parameter Group No. Default Blank Value Range 1-48 or 1-128 Description/Function Channel Type: LCO, GCO, DID, TIE (E&M) Specifies the Trunk Group (1-48) to which the T1 port is assigned. Channel Type: OPX Specifies the Extension Group (1-128) to which the T1 port is assigned.
Page 68: Disa Port Assignment
Configuration 1.7 DISA Port Assignment Used to assign OGM group number for each DISA card. Parameter [Card No. 1-8] Location Default (Display only) Value Range 101-314 Description/Function Displays the slot number of the DISA card which you are going to program.
Page 69: Bri Port Assignment
Configuration 1.8 BRI Port Assignment Used to assign the parameters for BRI (Basic Rate Interface) ports. Parameter Card No. Default — Value Range XXX: BRI [XXX: Card No. (101-314)] Description/Function Specifies the physical number of the BRI card which you are going to program.
Page 70 Configuration Parameter Type Default Value Range Description/Function Specifies the type of each BRI port either "CO" (CO line) or "EXT" (extension line) on a BRI port basis. Note • When you change the programming data, the status of the card must be made OUS (Out-of-Service), and then INS (In- Service).
Page 71 Configuration Parameter Group No. Default Value Range 1-48 or 1-128 Description/Function Type: CO Specifies the Trunk Group (1-48) to which the BRI port is assigned. Type: EXT Specifies the Extension Group (1-128) to which the BRI port is assigned. Reference •...
Page 72: Pri Port Assignment
Configuration 1.9 PRI Port Assignment Used to assign the parameters for PRI (Prime Rate Interface) ports. Parameter Card No. Default — Value Range XXX: PRI23 [XXX: Card No. (101–314)] Description/Function Specifies the physical number of the PRI23 card which you are going to program.
Page 73 Configuration Parameter Type Default Value Range Qsig – Master Qsig – Slave Description/Function Specifies the type of each PRI port on a PRI port basis. Notes • When you change the programming data, the status of the card must be made OUS (Out-of-Service), and then INS (In- Service).
Page 74 Configuration Parameter Group No. Default Value Range 1-48 or 1-128 Description/Function Type: CO, Qsig-Master, Qsig-Slave Specifies the Trunk Group (1-48) to which the PRI port is assigned. Type: EXT Specifies the Extension Group (1-128) to which the PRI port is assigned.
Page 75: System
System Section 2 System Programming Guide...
Page 76: System
System 2.1 System Used to assign parameters which affect system-wide operation. Programming Guide...
Page 77: Tenant
System 2.2 Tenant Used to assign various parameters on a tenant (1-8) basis. Parameter Tenant No. Default Value Range Description/Function Specifies the tenant (1-8) which you are going to program. Reference • 1.3 System Features (F/G) – Tenant Service Parameter Operator FDN Default Blank...
Page 78 System Parameter Alert Extension – Day / Night Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the destination extension which will be alerted by the system, if there is an extension user who did not respond to the Timed Reminder ringing (or Wake-Up Call).
Page 79 System Parameter Inter-tenant Calling (1 - 8) Default No check Value Range No check [Disallowed] Check [Allowed] Description/Function Specifies other tenant numbers to which extensions in this tenant can make a call. If no tenant numbers are checked in this field, extension users within this tenant cannot make a call to extensions in other tenants.
Page 80 System Parameter Lunch-Start (SUN-SAT) Default 12:00 PM Value Range Same as Day Description/Function Specifies the start time for Lunch Service. Reference • 1.3 System Features (F/G) – Night Service Parameter Lunch-End (SUN-SAT) Default 1:00 PM Value Range Same as Day Description/Function Specifies the end time for Lunch Service.
Page 81 System Parameter Music on Hold Source Default MUS1 Value Range None MUS1 MUS2 Tone Description/Function Specifies the Music Source port to be used for Music on Hold. Reference • 1.3 System Features (F/G) – Music on Hold • 2.8.2 External Music Source (I/M) Parameter BGM Source Default...
Page 82 System Parameter System Speed Dialing Entries Max. Default Tenant No. 1: 1000, Tenant No. 2: 1000, Tenant Nos. 3-8: 0 Value Range 0-1000 in 20 codes increments Description/Function Specifies the maximum number of Speed Dialing codes available for each tenant. Note •...
Page 83 System Parameter System Speed Dial TRS Level Override Default No check Value Range Check [Enable] No check [Disable] Description/Function Enables or disables "Toll Restriction Override for System Speed Dial Numbers" feature. If enabled (Check), all extension users in the tenant can make System Speed Dialing calls without toll restriction.
Page 84: Numbering Plan
System 2.3 Numbering Plan Used to assign the leading digits of extension numbers, and feature numbers for system features. Parameter 1 1st Hundred Block Extension Default Value Range 1-2 digits consisting of 0-9 Description/Function Specifies the leading 1 or 2 digits of the extension number. Any number "0 through 9"...
Page 85 System Parameter 2 2nd Hundred Block Extension Default Value Range 1-2 digits consisting of 0-9 Description/Function Same as the Parameter 1. Reference • 1.3 System Features (F/G) – Flexible Numbering Parameter 3 3rd Hundred Block Extension Default Value Range 1-2 digits consisting of 0-9 Description/Function Same as the Parameter 1.
Page 86 System Parameter 7 7th Hundred Block Extension Default Value Range 1-2 digits consisting of 0-9 Description/Function Same as the Parameter 1. Reference • 1.3 System Features (F/G) – Flexible Numbering Parameter 8 8th Hundred Block Extension Default Value Range 1-2 digits consisting of 0-9 Description/Function Same as the Parameter 1.
Page 87 System Parameter 11-16 11th Hundred Block Extension - 16th Hundred Block Extension Default Blank Value Range 1-2 digits consisting of 0-9 Description/Function Same as the Parameter 1. Reference • 1.3 System Features (F/G) – Flexible Numbering Parameter 17 Operator Call Default Value Range 1-4 digits consisting of 0-9,...
Page 88 System Parameter 20 Speed Dialing - System Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for making a call using a System Speed Dialing number. Reference • 4.3.73 System Speed Dialing (U/M) Parameter 21 Speed Dialing - Station Default Value Range...
Page 89 System Parameter 25 External Paging Answer / TAFAS Answer Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for answering paging announcements through External Pagers or TAFAS (Trunk Answer From Any Station) calls. Reference •...
Page 90 System Parameter 29 Group Call Pickup Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for answering a call ringing at another extension in the same Extension Group. Reference • 4.3.13 Call Pickup (U/M) Parameter 30 Directed Call Pickup Default...
Page 91 System Parameter 34 Redial Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for dialing the last number dialed. Reference • 4.3.66 Redial (U/M) Parameter 35 Call Park / Call Park Retrieve Default Value Range 1-4 digits consisting of 0-9, or # Description/Function...
Page 92 System Parameter 39 Station Program Clear Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for Station Program Clear. Reference • 4.3.71 Station Program Clear (U/M) Parameter 40 Message Waiting Set / Cancel / Call Back Default Value Range 1-4 digits consisting of 0-9,...
Page 93 System Parameter 43 Dial Call Pickup Deny Set / Cancel Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for setting / canceling the Dial Call Pickup deny feature. Reference • 4.3.14 Call Pickup Deny (U/M) Parameter 44 Data Line Security Set / Cancel Default...
Page 94 System Parameter 48 Absent Message Set / Cancel Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for setting / canceling Absent Message feature. Reference • 4.3.1 Absent Message Capability (U/M) Parameter 49 Timed Reminder Confirm / Set / Cancel Default Value Range 1-4 digits consisting of 0-9,...
Page 95 System Parameter 53 External BGM On / Off Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for turning on / off External BGM. [For Manager, Operator only] Reference • 4.4.2 Background Music (BGM) — External (U/M) Parameter 54 Live Call Screening Default...
Page 96 System Parameter 57 Timed Reminder, Remote Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for setting / canceling Timed Reminder, Remote feature. [For Manager, Operator only] Reference • 4.4.11 Timed Reminder, Remote (Wake-Up Call) (U/M) •...
Page 97 System Parameter 61 MODEM Control Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for External Modem Control. An external modem can be connected to RS-232C port 1. Reference • 4.3.36 External Modem Control (U/M) Parameter 62 Reserved (Reserved for future use.) Default...
Page 98 System Parameter 73 Remote FWD Cancel-Once Default Value Range 1-4 digits consisting of 0-9, or # Description/Function With this feature number, the Manager or the Operators can reach an extension that has set Call Forwarding. It is one time ("once") cancellation, not a permanent cancellation of Call Forwarding on the destination.
Page 99 System Parameter 77-92 Other PBX 01 - Other PBX 16 Default Blank Value Range 1-2 digits consisting of 0-9 Description/Function Specifies the leading 1 or 2 digits of the other PBX extension numbers. If you employ PBX code method for TIE calls, this programming is not required.
Page 100 System Parameter 96 CLIP Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for selecting a CLIP (Calling Line Identification Presentation) number for an outside line or an extension. Reference • 4.3.19 Calling Line Identification Presentation (CLIP) (U/M) Parameter 97 CLIR / CNIR Default...
Page 101 System Parameter 100 COS Primary Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for setting the COS Primary. Reference • 4.4.10 Switching COS (U/M) Parameter 101 COS Secondary Default Value Range 1-4 digits consisting of 0-9, or # Description/Function Specifies the feature number for setting the COS Secondary.
Page 102 System Parameter 105-120 Reserved (Reserved for future use.) Default Blank Value Range Description/Function Reference Programming Guide...
Page 103: Class Of Service (Cos)
System 2.4 Class of Service (COS) 2.4.1 Class of Service (COS) 1/2 Used to assign the Class of Service (COS) parameters. Parameter COS No. Default Value Range 1-96 Description/Function Specifies the COS (1-96) which you are going to program. Reference •...
Page 104 System Parameter TRS Level – Day / Night Default Value Range Description/Function Specifies the Toll Restriction level (1-8) for each COS number in Day / Night mode respectively. Reference • 1.6 Originating Features (F/G) – Toll Restriction Parameter Account Code Mode Default Optional Value Range...
Page 105 System Parameter Switching Day / Night Mode Default Disable Value Range Enable Disable Description/Function Enables or disables switching the Day / Night / Lunch / Break service on a Class of Service (COS) basis. Reference • 1.3 System Features (F/G) –...
Page 106 System Parameter Transfer to CO Default Disable Value Range Enable Disable Description/Function Enables or disables "Call Transfer to Trunk" feature. Reference • 4.3.16 Call Transfer (U/M) Parameter Call FWD to CO/TIE Default Disable Value Range Enable Disable Description/Function Enables or disables "Call Forwarding to Trunk" feature. Reference •...
Page 107 System Parameter Call FWD Follow Me Default Enable Value Range Enable Disable Description/Function Enables or disables "Call Forwarding - Follow Me" feature. Reference • 4.3.9 Call Forwarding (U/M) Parameter Busy Override Default Disable Value Range Enable Disable Description/Function Enables or disables "Executive Busy Override" feature. Reference •...
Page 108 System Parameter Released Link Operation Default Disable Value Range Enable Disable Description/Function Used to turn on / off "Released Link Operation" mode of the extension. When Released Link Operation is enabled, an extension user will be automatically released from a call (extension, outside) after transferring it to the destination, if the destination extension is idle.
Page 109 System Parameter Automatic Hold Default Disable Value Range Enable Disable Description/Function Used to turn on / off "Automatic Hold" feature. Reference • 1.10 Holding Features (F/G) – Automatic Hold—For Hold – Automatic Hold—For Transfer Parameter SDN COS Default Own Extension Value Range Own Extension Description/Function...
Page 110 System 2.4.2 Trunk Group Setting Used to specify the trunk group that the extension user can use for making an outside call. The following screen is shown on the display by clicking on "Class of Service" screen. Parameter Trunk Group No. 01-48 – Day / Night Default All: Check Value Range...
Page 111 System 2.4.3 Class of Service (COS) 2/2 Used to assign the Class of Service (COS) parameters. Parameter Secret Busy Override Default Disable Value Range Enable Disable Description/Function Enables or disables "Secret Busy Override" feature. Reference • 1.6 Originating Features (F/G) –...
Page 112 System Parameter Transfer to TIE Default Disable Value Range Enable Disable Description/Function Enables or disables "Call Transfer to TIE line" feature. Reference • 4.3.16 Call Transfer (U/M) • 1.11 Transferring Features (F/G) – Call Transfer Parameter Incoming Group FWD Default Disable Value Range Disable...
Page 113: System Timer
System 2.5 System Timer 2.5.1 System Timer 1/2 Used to assign various system timers. Parameter Hold Recall Time Default 60 s Value Range 0-240 s Description/Function Specifies the length of time in seconds that the system is to wait before alerting the extension user who held the call by Held Call Reminder ringing.
Page 114 System Parameter Transfer Recall Time Default 12 rings Value Range 0-48 rings Description/Function Specifies the number of rings before transfer recall occurs. If a transferred call is not answered before the programmed number of rings, the call returns to the extension user who originally transferred it or an Operator depending on the setting of "6.
Page 115 System Parameter Call Duration Count Start Time Default Value Range 0-60 s Description/Function Specifies the length of time in seconds the system is to wait after sending all dialing digits to the Central Office before starting the call duration count. Note •...
Page 116 System Parameter Call Forwarding-No Answer Time Default 3 rings Value Range 1-12 rings Description/Function Specifies the number of rings before the Call Forwarding No Answer feature is activated. If a call is not answered before the programmed number of rings, the call is redirected to the pre-assigned extension.
Page 117 System Parameter CO-to-CO Line Call Duration Time Default 10 min Value Range 1-64 min Description/Function Specifies the maximum time allowed for a call between two outside parties (CO-to-CO line call). If this timer expires during a CO-to-CO line call, it will be disconnected.
Page 118 System 2.5.2 System Timer 2/2 Used to assign various system timers. Parameter Timed Reminder Ringing Time Default 30 s Value Range 30-240 s Description/Function Specifies the length of ringing time in seconds of the Timed Reminder alarm. Reference • 1.8 Ringing Features (F/G) –...
Page 119 System Parameter Call Parking Recall Time Default 60 s Value Range 0-1800 s Description/Function Specifies the length of time in seconds the system is to wait before alerting (Call Parking Recall) the extension who parked the call. Note • If "0" is specified, Call Parking Recall does not occur. Reference •...
Page 120 System Parameter DISA Delayed Answer Time Default 1 ring Value Range 0-6 rings Description/Function Specifies the number of rings the system is to wait after receiving a DISA call before answering it. Note • A DISA call is answered after a ringback tone is returned to the caller after the "DISA Delayed Answer Time"...
Page 121 System Parameter DISA IRNA Time Default 60 s Value Range 5-240 s Description/Function Specifies the length of time in seconds the system is to wait before activating IRNA (Intercept Routing No Answer) feature for DISA calls. If a DISA call directed to a single extension is not answered within this timer, the system redirects the DISA call to another pre- programmed IRNA destination.
Page 122 System Parameter Timed Reminder Arrive Wait Time Default 60 s Value Range 20-240 s Description/Function Specifies the interval time between each Timed Reminder / Remote Timed Reminder (Wake-Up Call) attempt. Reference • 1.8 Ringing Features (F/G) – Timed Reminder (Wake-Up Call) –...
Page 123: Local Hunt Sequence
System 2.6 Local Hunt Sequence Specifies the trunk group hunt sequence to be used when an extension user attempts to make an outside call by dialing the feature number for "Local CO Line Access / ARS" or by pressing a Loop-CO key. Parameter Trunk Group No.
Page 124: Trunk To Trunk Restriction
System 2.7 Trunk to Trunk Restriction Used to allow or restrict the trunk-to-trunk relay function (routing a trunk call from one Trunk Group to another) on a trunk group basis. Please refer to "TIE Line Network – Alternate Routing" of Section "3.1 TIE Line Features" in the Features Guide for further information.
Page 125: System Option
System 2.8 System Option 2.8.1 System Option 1 Used to assign system option parameters (No.1 — No.10). Parameter 1. Sound source during transfer Default Music on Hold Value Range Ringback Tone Music on Hold Description/Function Used to determine whether the system sends "Music on Hold" or "Ringback Tone"...
Page 126 System Parameter 2. SLT On-hook with consulting held call Default Consulting Hold Value Range Consulting Hold Disconnect Description/Function Specifies the result of pressing the switchhook lightly and then replacing the handset during an outside call. This setting applies to SLT users only. Reference •...
Page 127 System Parameter 5. Limited call duration Default Both calls Value Range Outgoing call only Both calls Description/Function Limited call duration is a system programmable feature that disconnects an outside call when a specified timer expires. A warning tone is sent to the extension user 15 seconds, 10 seconds, and 5 seconds before the time limit.
Page 128 System Parameter 7. Checking dial *, # by toll restriction Default Check Value Range No check [Disable] Check [Enable] Description/Function Specifies whether or not the system checks the user-dialed " " and "#" during Toll Restriction procedure. Note • This assignment is required for certain Central Offices (COs) to prevent toll fraud.
Page 129 System Parameter 10. Station Speed Dialing Initial display Default Name Value Range Name Number Description/Function Specifies the initial display of a display DPT, such as KX-T7235 / KX-T7436, in Station Speed Dialing. Reference • 4.5.8 KX-T7235 Display Features - Call Directory (U/M) •...
Page 130 System Parameter 12. Automatic adjustment of the clock using Caller ID information Default Value Range Description/Function Enables or disables the automatic adjustment of the clock by Caller ID information once a day. Reference • 1.5 Attended Features (F/G) – Caller ID Service Parameter 13.
Page 131 System Parameter 15. Special dial tone after setting feature Default Enable Value Range Enable Disable Description/Function If enabled, the system notifies the extension user by sending a special dial tone (Dial Tone 2) when one or more of the following features are assigned on his extension.
Page 132 System Parameter 18. Destination Busy - DID Default Send busy tone Value Range Send busy tone Transferred to IRNA destination Wait till the destination becomes idle Description/Function Specifies the treatment of DID callers when they dial a busy extension. Reference •...
Page 133 System 2.8.3 System Option 3 Used to assign system option parameters (No.21 — No.30). Programming Guide...
Page 134 System Message Waiting lamp patterns (1/2) The available message waiting lamp patterns are as follows: 5.12 1.28 Pattern #01 5.12 1.28 Pattern #02 512 ms 5.12 1.28 Pattern #03 256 ms 2.56 768 ms Pattern #04 256 ms 2.56 512 ms Pattern #05 1.28 Pattern #06...
Page 135 System Message Waiting lamp patterns (2/2) 1.28 Pattern #07 256 ms 1.28 Pattern #08 1.28 Pattern #09 t=1.28 Pattern #10 t=1.28 Pattern #11 5.12 768 ms Pattern #12 256 ms Programming Guide...
Page 136 System Parameter 21. Illegal Number - DISA Default Send reorder tone Value Range Send reorder tone Transferred to IRNA destination Description/Function Specifies the treatment of the invalid DISA calls. Reference • 1.5 Attended Features (F/G) – Direct Inward System Access (DISA) Parameter 22.
Page 137 System Parameter 25. Pressing DSS key operation in CO talking Default Hold Value Range Disconnect Hold Description/Function If set to "Hold," the PT user engaged in a CO call can transfer the current call to another extension simply by pressing the DSS button associated with the destination extension.
Page 138 System Parameter 28. Trunk hunting mode Default Forced Value Range Forced Loop Detection Description/Function Specifies the trunk hunting mode. Forced: The system seizes a trunk line whether or not loop current is detected from the local CO. Loop Detection: The system seizes a trunk line after detecting loop current from the local CO.
Page 139 System 2.8.4 System Option 4 Used to assign system option parameters (No.31 — No.49). Parameter 31. Answering Call Waiting call by SLT hooking Default Disable Value Range Enable Disable Description/Function If enabled, an SLT user can answer a call waiting call simply by flashing the switchhook.
Page 140 System Parameter 33. FWD / DND lamp pattern Default FWD: Flash, DND: On Value Range FWD: Flash, DND: On FWD: On, DND: Flash Description/Function Specifies the lamp patterns of the FWD / DND button. Reference • 1.8 Ringing Features (F/G) –...
Page 141 System Parameter 36. Tone Mode Default Type-1 Value Range Type-1 Type-2 Type-3 Type-4 Type-5 Type-6 Type-7 Description/Function Specifies the Tone output type. Note • The change of this parameter is activated after resetting the system. Reference None Parameter 37. Ring Mode Default Type-1 Value Range...
Page 142 System Parameter 41. Fixed Feature Number Default Type-1 Value Range Type-1 Type-2 Description/Function Specifies a type of Fixed Feature Numbers. Reference • 1.3 System Features (F/G) – Flexible Numbering • 6.1.2 Feature Numbers List (U/M) Parameter 42. DPT Ringer OFF Default Enable Value Range...
Page 143 System Parameter 47. Tone Type for Outgoing Calls Default Busy + Reorder Value Range Busy + Reorder Busy Reorder Description/Function Specifies a tone type for outgoing calls. Reference None Parameter 48. Call Pickup with DSS S-CO key Default Disable Value Range Enable Disable Description/Function...
Page 144 System 2.8.5 System Option 5 Used to assign system option parameters (No.56 — No.60). Parameter 56. Redial with ISDN Default Do not send dials entered during conversation Value Range Do not send dials entered during conversation Send dials entered during conversation Description/Function This parameter is available only when redialing using ISDN.
Page 145 System Parameter 58. Release of BRI/PRI line while talking when 'DISCONNECT' signal is received Default Don’t Release Value Range Release Don't Release Description/Function Specifies whether or not the system releases the ISDN BRI / PRI line, when receiving the line disconnection message from the ISDN Network while the line is in talking.
Page 146 System 2.8.6 System Option 6 Used to assign system option parameters (No.61 — No.67). Parameter 61. Auto Answer with held call Default Disable Value Range Disable Enable Description/Function Specifies whether the PT user automatically answers the intercom call on Consultation Hold or not. Reference •...
Page 147 System Parameter 64. CNIP Service Default Disable Value Range Disable Enable Description/Function Specifies whether or not to use the CNIP (ISDN) service on outgoing CO calls. Reference • 2.2 ISDN Originating Features (F/G) – Calling Name Identification Presentation (CNIP) Parameter 65.
Page 148: Pri Originating Control
System 2.9 PRI Originating Control Used to specify the inter-digit timers and the trunk group on an outgoing call using an ISDN PRI line. Parameter PRI Inter-digit Timer-1 Default Value Range 1-30 s Description/Function Specifies the maximum time allowed between each digit on an outgoing call using an ISDN PRI line.
Page 149 System Parameter PRI Inter-digit Timer-2 Default Value Range 1-30 s Description/Function Specifies the maximum time allowed between each digit on an outgoing call using an ISDN PRI line. Note • This timer applies to the call before the number of digits determined by "Dial counter for PRI Inter-digit Timer-2"...
Page 150 System Programming Guide...
Page 151: Group
Group Section 3 Group Programming Guide...
Page 152: Group
Group 3.1 Group Used to assign various group parameters. Programming Guide...
Page 153: Trunk Group
Group 3.2 Trunk Group 3.2.1 Trunk Group 1/2 Used to assign parameters for each trunk group. Up to 48 trunk groups can be created in the system. Note • To support efficient utilization of trunks, it is desirable to group them together in trunk groups according to a type of each trunk (Incoming Only, Outgoing Only or Both-Way) determined by the contract with the Central Office.
Page 154 Group Trunk Group Copy Used to copy a part of or all settings of a certain Trunk Group to all other Trunk Groups at a time. You can also specify one or several Trunk Groups as the copy destination. Copying the Trunk Group Parameters to Other Trunk Groups 1.
Page 155 Group Parameter Group No. Default Value Range 1-48 Description/Function Specifies the trunk group (1-48) which you are going to program. Reference 1.3 System Features (F/G) – Trunk Group Parameter Copy Default — Value Range — Description/Function You can enter into "Trunk Group Copy" screen by clicking this button.
Page 156 Group Parameter Pause Time before Flash Signal Default 512 ms Value Range None 512 ms 1024 ms 1536 ms 2048 ms Description/Function Specifies the pausing time required before sending the Flash Signal. Reference None Parameter Max. Dial No. after EFA Signal Default Value Range 0-32...
Page 157 Group Parameter Line Hunting Order Default Reverse Value Range Normal Reverse Sequential Description/Function Specifies the hunting sequence of idle lines on a trunk group basis. Normal: The system connects the user to an idle trunk line with the lowest physical number. Reverse: The system connects the user to an idle trunk line with the highest physical number.
Page 158 Group Parameter Flash Time Default 600 ms Value Range None 80 ms 300 ms 600 ms 900 ms 1200 ms Description/Function Specifies the length of flash time. Notes • When you need finer resolution, assign this to 80 ms and use "Flash Time"...
Page 159 Group Parameter Pause Time Default 1.5 s Value Range 1.5 s 2.5 s 3.5 s 4.5 s Description/Function Specifies the length of pause time (dialing delay). The programmed pause time is automatically inserted after a line access code or a host PBX access code, or manually inserted when the PAUSE button is pressed by the extension user.
Page 160 Group Parameter [Numbering Plan ID] Outgoing—Private Default Private Value Range Default Unknown ISDN / Telephony National Standard Private Description/Function Specifies the Numbering Plan ID applied to the outgoing CO calls via ISDN Private Network. Reference None Parameter [Numbering Plan ID] Incoming—Public Default Default Value Range...
Page 161 Group Parameter PBX Dial Tone Default Disable Value Range Enable Disable Description/Function If enabled, the system sends a dial tone to the extension user who seizes a T1 digital trunk line. (Available for T1 digital trunk lines only.) Note • In case of the T1 digital trunk line, the Central Office does not send a dial tone to the caller.
Page 162 Group Parameter [Type of Number] Outgoing—Private Default Default Value Range Default Unknown International National Network Specific Subscriber Description/Function Specifies the Type of Number applied to the outgoing CO calls via ISDN Private Network. Reference None Parameter [Type of Number] Incoming—Public Default Default Value Range...
Page 163 Group Parameter Cyclic Signal Detection Default Check Value Range No check [Disable] Check [Enable] Description/Function Used to disconnect the trunk line when the system detects a cyclic signal during a CO-to-CO line call by DISA or AGC. Reference • 1.5 Attended Features (F/G) –...
Page 164 Group 3.2.2 Trunk Group 2/2 Used to assign parameters for each trunk group. Up to 48 trunk groups can be created in the system. Parameter ISDN Progress Tone Mode Default Automatic Value Range Automatic Network Description/Function Selects the way to supply the progress tone to an extension when the extension user makes an outgoing call via ISDN.
Page 165 Group Parameter IRNA for TIE Line Default Disable Value Range Enable Disable Description/Function Specifies whether the "Intercept Routing" feature on an incoming TIE call is enabled or not. Reference • 1.11 Transferring Features (F/G) – Intercept Routing • 4.2 Trunk Line (P/G) Programming Guide...
Page 166: Extension Group
Group 3.3 Extension Group Used to assign various parameters for up to 128 (1-128) Extension Groups. Which parameters apply to your Extension Group? Please refer to the table on the Page 167 and Page 168. Note • By default, the Group Type of Group No.126 is VM, No.127 is AA and No.128 is Operator.
Page 167 Group Applicability of Parameters to Group Types Group Type Parameter None Ter. Cir. Ring Ope. Group No. Tenant No. [Overflow Setting] Destination – Day / Night [Overflow Setting] Timer FWD / DND Mode Extension Call Hunting Calls to Empty Group [Operator Setting] Ringing Type [Operator Setting]...
Page 168 Group Applicability of Group Types to Overflow Destinations Overflow Destination Group External Extension Phantom Incoming Type Pager Group Group Extension Group None Terminate Circular Operator ( = assignable) When "DIL 1:N" is specified in "Group Type" programming of Incoming Group, this feature does not work.
Page 169 Group Extension Group Copy Used to copy a part of or all settings of a certain Extension Group to all other Extension Groups at a time. You can also specify one or several Extension Groups as the copy destination. Copying the Extension Group Parameters to Other Extension Groups 1.
Page 170 Group 6. Point to and click. • "Copying" is displayed while the source data is being copied to the destination. • Parameters of the destination Extension Groups are immediately effective when copying is finished. Parameter Group No. Default Value Range 1-128 Description/Function Specifies the Extension Group (1-128) which you are going to...
Page 171 Group Parameter Tenant No. Default Value Range Description/Function Specifies the tenant (1-8) to which the Extension Group is assigned. (Required when "Tenant Service" is employed.) Reference •1.3 System Features (F/G) – Tenant Service • 2.2 Tenant (P/G) Parameter [Overflow Setting] Destination – Day / Night Default Blank Value Range...
Page 172 Group Parameter Group Type Default Group No.126: VM, Group No.127: AA, Group No.128: Operator, Others: None Value Range None Terminate Circular Ring Operator Description/Function Specifies the Group Type for each Extension Group. This determines how the Extension Group handles the incoming calls directed to it.
Page 173 Group Parameter FWD / DND Mode Default Enable Value Range Disable Enable Description/Function Specifies whether to enable or disable the FWD / DND (Call Forwarding or Do Not Disturb) feature assigned on all extensions in the Extension Group. (Assignable only when "Terminate," "Ring," "Circular" or "UCD" is specified in "Group Type"...
Page 174 Group Parameter Calls to Empty Group Default Disable Value Range Enable Disable Description/Function Allows for calls to empty (all Logout) Operator or UCD Groups to be queued. If enabled, calls will be queued to the group. If disabled, the extension will receive a reorder tone, and the CO call will be transferred to the overflow destination immediately.
Page 175 Group Parameter [UCD Setting] FWD No Answer Default Disable Value Range Disable Enable Description/Function Specifies the treatment of the call which is not answered by the extension in the UCD group within a specified period of time (Call Forwarding - No Answer Time). Disable: The call continues to ring the current destination extension.
Page 176 Group Parameter [UCD Setting] Supervisor Extension Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the Supervisor Extension per UCD Group. The extension specified as the Supervisor Extension can monitor the number of waiting calls (calls placed in the waiting queue). Reference •...
Page 177 Group Parameter [UCD Setting] UCD Call Waiting Default Enable Value Range Disable Enable Description/Function This feature is different from regular Call Waiting. This feature (if enabled) allows UCD group members to hear a Call Waiting tone when an inside / outside call arrives but all the extensions in the UCD Group are busy.
Page 178 Group Parameter [Operator Setting] Ringing Type Default Single Value Range Multi Single Description/Function Specifies whether the calls coming in on an Operator Group ring one Operator (Single) or all Operators in the group (Multi) simultaneously. (Assignable only when "Operator" is specified in "Group Type" programming.) Reference •1.3 System Features (F/G)
Page 179: Paging Group
Group 3.4 Paging Group Used to program up to 16 Paging Groups. Each Paging Group consists of up to 24 Extension Groups. One Extension Group can be assigned to only one Paging Group. Parameter Paging Group No. Default Value Range 1-16 Description/Function Specifies the Paging Group (1-16) which you are going to program.
Page 180: Incoming Group
Group 3.5 Incoming Group Used to program a list of up to 96 Incoming Groups. Which parameters apply to your Incoming Group? Please refer to the table on Page 181 and Page 182. Programming Guide...
Page 181 Group Applicability of Parameters to Group Types Group Type Parameter DIL 1:N Ter. Ring Ope. [Overflow Setting] Destination — Day / Night [Overflow Setting] Timer FWD / DND Mode Search Mode Calls to Empty Group [Operator Setting] Ringing Type [Operator Setting] Call Priority [UCD Setting] Time Table No.
Page 182 Group Applicability of Group Types to Overflow Destinations Overflow Destination Group External Extension Phantom Incoming Type Pager Group Group Extension Group Terminate Operator ( = assignable) When "DIL 1:N" is specified in "Group Type" programming of Incoming Group, this feature does not work.
Page 183 Group 3. Select the Incoming Group parameters to copy in "Copy Item" field. • Only parameters which are available to copy are shown in "Copy Item" field. This depends on the Group Type assignment of the copy source Incoming Group. •...
Page 184 Group Parameter Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the FDN (Floating Directory Number) for the Incoming Group. Reference • 1.3 System Features (F/G) – Floating Station Parameter DN Refer Default — Value Range — Description/Function Displays the list of DNs/FDNs which are already assigned to the extensions / system resources.
Page 185 Group Parameter [Overflow Setting] Destination – Day / Night Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the destination extension where the call is transferred to when all extensions in the Incoming Group are unavailable or logged-out in Day / Night mode respectively. (Assignable only when "Terminate,"...
Page 186 Group Parameter FWD / DND Mode Default Enable Value Range Disable Enable Description/Function Specifies whether to enable or disable the FWD / DND (Call Forwarding or Do Not Disturb) feature assigned on all extensions in the Incoming Group. (Assignable only when "Terminate," "Ring" or "UCD" is specified in "Group Type"...
Page 187 Group Parameter Calls to Empty Group Default Disable Value Range Enable Disable Description/Function Allows for calls to empty (all Logout) Operator or UCD Groups to be queued. If enabled, calls will be queued to the group. If disabled, the extension will receive a reorder tone, and the CO call will be transferred to the overflow destination immediately.
Page 188 Group Parameter [UCD Setting] FWD No Answer Default Disable Value Range Disable Enable Description/Function Specifies the treatment of the call which is not answered by the extension in the UCD group within a specified period of time (Call Forwarding - No Answer Time). Disable: The call continues to ring the current destination extension.
Page 189 Group Parameter [UCD Setting] Supervisor Extension Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the Supervisor Extension per UCD Group. The extension specified as the Supervisor Extension can monitor the number of waiting calls (calls placed in the waiting queue) and the Login/Logout status of UCD Group members through the corresponding DSS buttons.
Page 190 Group Parameter [Operator Setting] Call Priority Default CO Call: 1, Intercept Routing: 2, Recall: 3, Extension Call: 4 Value Range Priority 1-4 Description/Function Specifies the answering priority of incoming calls to the Operator Group by a type of call when more than one call is ringing at an Operator extension.
Page 191 Group 3.5.1 Destination for Incoming Group You can assign up to 72 extensions or Extension Groups or both per Incoming Group so that an incoming CO call rings multiple extensions simultaneously. Parameter [Destinations] DN Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies extensions or Extension Groups or both that you are going to assign to the specified Incoming Group.
Page 192 Group Parameter [Destinations] Ringing Type Default Immediate Value Range Immediate 1-ring Delay 3-ring Delay 6-ring Delay No Ring Description/Function Specifies the ringing delay of the calls arriving at extensions whose "Group Type" programming is specified as "DIL 1:N." Immediate: An extension rings immediately. 1-ring Delay: An extension rings in 1-ring delay timing.
Page 193: Ogm Group
Group 3.6 OGM Group Used to assign parameters for OGM Groups (1-8). OGM resources on the DISA card can be grouped together as an OGM Group. Parameter Group No. Default Value Range Description/Function Specifies the OGM Group (1-8) which you are going to program. Reference None Parameter...
Page 194 Group Parameter DN Refer Default — Value Range — Description/Function Displays the list of DNs/FDNs which are already assigned to the extensions/system resources. Reference None Parameter Tenant No. Default Value Range Description/Function Specifies the tenant (1-8) to which you are going to assign this OGM Group.
Page 195 Group Parameter Security Mode Default Trunk Value Range None Trunk Description/Function Specifies the Security Mode for DISA callers. (Assignable only when "DISA" is specified in "OGM Type" programming.) None (Non security mode): DISA callers can make both outside and intercom calls via DISA without restriction.
Page 196 Group Programming Guide...
Page 197: Line
Line Section 4 Line Programming Guide...
Page 198: Line
Line 4.1 Line Used to assign various parameters for both trunk and extension lines. Programming Guide...
Page 199: Trunk Line
Line 4.2 Trunk Line Used to assign various parameters for trunk lines. Programming Guide...
Page 200 Line Trunk Line Copy Used to copy a part of or all settings of a certain Trunk Line to all other same type Trunk Lines at a time. You can also specify one or several Trunk Lines as the copy destination. This copy function is available between the Trunk Lines of the same type Trunk Cards.
Page 201 Line 6. Point to and click. • "Copying" is displayed while the source data is being copied to the destination. • Parameters of the destination Trunk Lines are immediately effective when copying is finished. Parameter Card No. Default — Value Range XXX: YYY [XXX: Card No.
Page 202 Line Parameter Name Default CO001-CO192 Value Range Up to 10 characters consisting of 0-9, A-Z, a-z or the following marks: ! # $ % ( ) + , - / : ; < = > ? @ &. Description/Function Specifies the name for the trunk line. Note •...
Page 203 Line Parameter Incoming Type Description/Function <Available selections and the default values per Card Type> Card Type Selection Default DID(ISDN)/MDN DID(ISDN) T1(TIE) DIL/TIE LCOT, GCOT, ELCOT, T1 (LCO), T1 (GCO) T1 (DID) DIL/DID PRI23 TIE/DID(ISDN) DID(ISDN) Note • In some cases, the default cannot be changed. Reference •...
Page 204 Line Parameter Dial Type Default DTMF-80: ELCOT/GCOT/LCOT/T1/DID card, ISDN: BRI/ PRI23 card Value Range Pulse-10 (10 PPS) Pulse-20 (20 PPS) DTMF-80 (80 ms) DTMF-160 (160 ms) ISDN Description/Function Specifies the dial type for each trunk line. This is the dial type regardless of the dial mode of the extension telephone.
Page 205 Line Parameter Destination—Day/Night/Lunch/Break Default Day, Night: 1001, Lunch, Break: Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the destination for the trunk line whose "Incoming Type" is set to "DIL." The following numbers can be assigned as the destination: Extension numbers, FDNs.
Page 206 Line Parameter [DID/TIE] Digits to delete Default Value Range 0-16 digits Description/Function Specifies the number of digits to be deleted from the number received from the DID/DID (ISDN)/other PBX via TIE lines. Reference • 1.5 Attended Features (F/G) – Direct Inward Dialing (DID) •...
Page 207 Line Parameter Wink Signal Time-out Default 1024 ms Value Range 64 ms 128 ms 256 ms 512 ms 1024 ms 2048 ms 4096 ms 8128 ms Description/Function Specifies the length of time in milliseconds that the system is to wait for the Wink Signal after seizing the trunk. (Assignable only when "Start Signal Type"...
Page 208 Line Parameter Answer Wait Timer Default None Value Range None 1 min 2 min 3 min 4 min Description/Function Specifies the length of time in minutes the system waits, after an outgoing CO call is made, before the other party answers the call. If the call is not answered before this timer expires, the call will be disconnected automatically.
Page 209 Line Parameter [CPC Signal] IN Detection Default Enable: DID/ELCOT/GCOT/LCOT/T1 [GCO]/T1 [LCO] card Value Range Enable Disable Description/Function Specifies whether CPC Detection on incoming CO calls is enabled or disabled. If enabled, the system disconnects the line with the time set in program "[CPC Signal] IN Detection—Detection Time"...
Page 210 Line Parameter [TIE Line] Sending TIE Caller ID Default Value Range Description/Function Specifies whether to send or not the TIE Caller ID to the other end. Reference • 3.1 TIE Line Features (F/G) – TIE Line Service Parameter Caller ID Default Disable Value Range...
Page 211: Extension Line
Line 4.3 Extension Line 4.3.1 Extension Line 1/2 Used to assign parameters for extension lines. Programming Guide...
Page 212 Line Extension Line Copy Used to copy a part of or all settings of a certain Extension Line to all other Extension Lines at a time. You can also specify one or several Extension Lines as the copy destination. Copying the Extension Line Parameters to Other Extension Lines 1.
Page 213 Line Parameter Card No. Default — Value Range XXX: YYY [XXX: Card No. (101-314), YYY: Card Type] Description/Function Specifies the physical number of the extension card and its type, which you are going to program. Reference • 1.2 Slot Assignment (P/G) Parameter Port No.
Page 214 Line Parameter Copy Default — Value Range — Description/Function You can enter into "Extension Line Copy" screen by clicking this button. Reference — Parameter Name Default Blank Value Range Up to 10 characters consisting of 0-9, A-Z, a-z or the following marks: ! # $ % ( ) + , - / : ;...
Page 215 Line Parameter Mailbox No. Default Same as the extension number Value Range Up to 16 digits consisting of 0 - 9, , # or P [Pause] Description/Function Specifies the mailbox number which is usually the same as the extension number. Note •...
Page 216 Line Parameter Initial Display Selection Default Caller ID Value Range Caller ID Trunk Name DID Name Description/Function Specifies the initial display of a display PT when an incoming CO call with Caller ID information comes in on it. Reference • 2.2.6 Initial Display Selection (U/M) Parameter [COS No.] Primary Default...
Page 217 Line Parameter [Preferred Line] Outgoing - Key No. Default Blank Value Range 1-24 Description/Function Specifies the CO button to which the extension is connected when the extension user goes off-hook to make a call. This assignment is required when "Prime Line - CO" is specified in "[Preferred Line] Outgoing"...
Page 218 Line Parameter [Pickup Dialing] Dial Default (Display only) Value Range Up to 24 digits Description/Function Displays the telephone number for "Pickup Dialing" feature. The system automatically dials this number when an extension user goes off-hook to make a call, if "Pickup Dialing" is enabled. Reference •...
Page 219 Line Parameter [LCS Setting] Recording Mode Default Stop Rec Value Range Keep Rec Stop Rec Description/Function Assigns whether to close the mailbox or keep recording the conversation after a call is interrupted. Reference • 1.9 Answering Features (F/G) – Live Call Screening (LCS) Parameter [LCS Setting] LCS Password Default...
Page 220 English Value Range English French Description/Function Specifies the language shown on a PANASONIC display PT. The language is set for each extension, so phones on the same system can display different languages. Reference • 2.2.1 Bilingual Display Selection (U/M) Parameter...
Page 221 Line Parameter ISDN Bearer Mode Default Automatic Value Range Automatic Speech 3.1 KHz Audio Description/Function Specifies the ISDN Bearer Mode on an extension basis. Note • When "Automatic" (Default) is selected, Bearer Mode is set automatically depending on the type of extension telephone as follows: PT - Speech, SLT - 3.1 KHz Audio, ISDN extension - depending on the bearer mode of the ISDN extension.
Page 222 Line Parameter [CLIP Number] Public Default Blank Value Range Up to 16 digits consisting of 0 - 9, or # Description/Function Specifies a CLIP number used for the incoming / outgoing calls via Public Switched Telephone Network to each extension. Notes •...
Page 223 Line Parameter [Call Log Incoming] Overwrite Mode Default Value Range Description/Function Enables or disables Call Log Incoming, Overwrite Mode. If the Call Log is full (30 call records are already logged) when a new Caller ID call comes in. Yes: The new call record overwrites the oldest one in the Call Log.
Page 224 Line 4.3.2 Flexible CO Key Assignment Used to determine the usage of flexible CO buttons on PTs. The following screen is displayed by clicking on "4-2 Extension Line" screen. <Key Type Assignment> The following Key Type Assignment screen is displayed by clicking "Key Type Display" button (including "Not Stored") for each CO key on the above screen.
Page 225 Line Additional Key Type Parameters Description (default) SINGLE-CO Trunk Line Specifies the trunk port physical number (10101 to 31416). Tone (2) Specifies the ringer frequency (ring tone type: 1-8) for incoming calls. GROUP-CO Trunk Group Specifies the Trunk Group number (01 - 48). Tone (2) Specifies the ringer frequency (ring tone type: 1-8) for incoming calls.
Page 226 Line Additional Key Type Parameters Description (default) Specifies the Directory Number of the Voice Mail extension. 2WAY-REC Specifies the Directory Number of the Voice Mail extension. 2WAY-TRN Specifies the Directory Number of the Voice Mail extension. Parameter Key Type Default CO-01: Loop-CO, Others: Not Stored Value Range Please refer to "Description / Function."...
Page 227 Line 4.3.3 Flexible PF Key Assignment for PT Used to determine the usage of flexible PF buttons on PTs. The following screen is displayed by clicking on "4-2 Extension Line" screen. <Key Type Assignment> The following Key Type Assignment screen is displayed by clicking "Key Type Display" button (including "eNot Stored") for each PF Key on the above screen.
Page 228 Line <Additional Parameters Required by Key Type> Depending on a Key Type, additional parameters are required as follows. Additional Key Type Description Parameters ONE-TOUCH Dial Specifies the telephone number or feature access number (up to 24 digits consisting of 0 - 9, , #, -, P, S or F). Note •...
Page 229 Line 4.3.4 Extension Line 2/2 Used to assign parameters for extension lines. Parameter Intercept Destination — Day / Night Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the destination extension (3 or 4 digits) for Intercept Routing feature in both Day and Night modes respectively. Notes •...
Page 230 Line Parameter Call Forwarding-No Answer Time Default 0 ring Value Range 0-12 rings Description/Function Specifies the number of rings before the Call Forwarding No Answer feature is activated. If a call is not answered before the programmed number of rings, the call is redirected to the pre-assigned extension.
Page 231: Dss Console
Line 4.4 DSS Console Used to assign the paired extension for a DSS (Direct Station Selection) Console and the usage of DSS and PF buttons. Programming Guide...
Page 232 Line DSS Console Copy Used to copy a part of or all settings of a certain DSS Console to all other DSS Consoles at a time. You can also specify one or several DSS Consoles as the copy destination. Copying the DSS Console Parameters to Other DSS Consoles 1.
Page 233 Line Notes • Flexible DSS / PF Key Assignment should be done before executing this copy function. • Copy function is not available in the Interactive mode. Parameter Paired Extension Default — Value Range 3-4 digits consisting of 0-9 Description/Function Displays the extension paired with the DSS Console.
Page 234 Line Parameter PF Key Default — Value Range — Description/Function You can enter into "Flexible PF Key" screen (Section 4.4.2) by clicking on this screen. Reference • 2.2.3 Flexible Button Assignment (U/M) • 5.2.1 Station Programming (U/M) Parameter Copy Default —...
Page 235 Line <Key Type Assignment> The following Key Type Assignment screen is displayed by clicking "Key Type Display" button (including "Not Stored") for each DSS Key on the above screen. <Additional Parameters Required by Key Type> Depending on a Key Type, additional parameters are required as follows. Additional Key Type Description...
Page 236 Line Parameter Key Type Default Not Stored Value Range Please refer to "Description / Function." Description/Function Not Stored: Key Type is not assigned. SINGLE-CO: Single-CO button GROUP-CO: Group-CO button DSS: Direct Station Selection button ONE-TOUCH: One-Touch Dialing button MESSAGE: Message Waiting button MESSAGE-OTHER: Another Extension/Phantom Extension Message Waiting button FWD / DND: Call Forwarding / Do Not Disturb button...
Page 237 Line 4.4.2 Flexible PF Key Assignment for DSS Console Used to determine the usage of flexible PF buttons on DSS Consoles. The following screen is displayed by clicking on "4-3 DSS Console" screen. Programming Guide...
Page 238 Line <Key Type Assignment> The following Key Type Assignment screen is displayed by clicking "Key Type Display" button (including "Not Stored") for each PF Key on the above screen. <Additional Parameters Required by Key Type> Depending on a Key Type, additional parameters are required as follows. Additional Key Type Description...
Page 239 Line Parameter Key Type Default Not Stored Value Range Please refer to "Description / Function." Description/Function Not Stored: Key Type is not assigned. ONE-TOUCH: One-Touch Dialing button FWD / DND: Call Forwarding / Do Not Disturb button SAVE: Saved Number Redial button ACCOUNT: Account Code entry button CONF: Conference button VTR: Voice Mail Transfer button...
Page 240: Doorphone
Line 4.5 Doorphone Used to assign the destination extensions for incoming calls from doorphones. Parameter Card No. Default — Value Range XXX: DPH [XXX: Card No. (101-314)] Description/Function Specifies the physical number of a doorphone card which you are going to program. Reference •...
Page 241 Line Parameter Tenant No. Default Value Range 1 - 8 Description/Function Specifies the tenant (1-8) to which the doorphone port is assigned. Reference • 1.3 System Features (F/G) – Tenant Service • 1.12 Conversation Features (F/G) – Doorphone Call • 2.2 Tenant (P/G) Parameter Destination –...
Page 242: External Paging
Line 4.6 External Paging Used to assign parameters for External Paging. Parameter Pager No. Default (Display only) Value Range 1, 2 Description/Function Displays the Pager No. Reference • 2.8.1 External Pager (Paging Equipment) (I/M) Parameter Tenant No. Default Value Range Description/Function Specifies the tenant to which the External Pager is assigned.
Page 243 Line Parameter Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the FDN (Floating Directory Number) for the External Pager. Reference • 1.3 System Features (F/G) – Floating Station Parameter Default No check Value Range No check [Disable] Check [Enable] Description/Function Specifies whether BGM is sent or not when the External Pager is...
Page 244: Isdn Extension Line
Line 4.7 ISDN Extension Line Used to assign parameters for ISDN extension lines. Parameter Card No. Default — Value Range XXX: BRI [XXX: Card No. (101-314)] Description/Function Specifies the physical number of the BRI card which you are going to program. Reference •1.2 Slot Assignment (P/G) Parameter...
Page 245 Line Parameter Group No. Default (Display only) Value Range 1-128 Description/Function Displays the Extension Group to which the selected ISDN extension port is assigned. Reference • 1.8 BRI Port Assignment (P/G) Parameter Name Default Blank Value Range Up to 10 characters consisting of 0-9, A-Z, a-z or the following marks: ! # $ % ( ) + , - / : ;...
Page 246 Line Parameter ISDN Bearer Mode Default Automatic Value Range Automatic Speech 3.1 KHz Audio Description/Function Specifies the ISDN Bearer Mode on an ISDN extension basis. Note • When "Automatic" (Default) is selected, Bearer Mode is set automatically depending on the type of extension telephone as follows: PT –...
Page 247 Line Parameter [CLIP Number] Public Default Blank Value Range Up to 16 digits consisting of 0-9, or # Description/Function Specifies a CLIP number used for the incoming / outgoing calls via Public Switched Telephone Network to each ISDN extension. Notes •...
Page 248 Line Parameter [COS No.] Primary Default Value Range 1-96 Description/Function Specifies the Primary COS (Class of Service) (1-96) to the ISDN extension. Reference • 1.3 System Features (F/G) – Class of Service (COS) • 4.4.10 Switching COS (U/M) Parameter [COS No.] Secondary Default Value Range 1-96...
Page 249: Features
Features Section 5 Features Programming Guide...
Page 250: Features
Features 5.1 Features Used to assign parameters for various system features. Programming Guide...
Page 251: System Speed Dialing
Features 5.2 System Speed Dialing Used to program a list of up to 1000 (000-999) frequently dialed numbers per tenant. Anyone in the same tenant can dial these numbers. Up to 2000 Speed Dialing codes can be shared among tenants under the limitation of 1000 codes per tenant.
Page 252 Features Parameter Max. Entry Default (Display only) Value Range 0-1000 Description/Function Displays the maximum number of Speed Dialing codes allocated to the tenant. Reference • 1.3 System Features (F/G) – Tenant Service • 2.2 Tenant (P/G) Parameter Current Registration Default (Display only) Value Range 0-1000...
Page 253 Features Parameter Number Default Blank Value Range Up to 24 digits consisting of 0-9, , #, -, P, S or F Description/Function Specifies the telephone number for each speed dial code. Note • P: Pause, S: Secret Dialing, F: Hook Flash Reference None Programming Guide...
Page 254: Phantom Extension
Features 5.3 Phantom Extension Used to register up to 448 Phantom Extension numbers. Parameter Entry No. Default 001-048 Value Range 001-448 in 48 codes increments Description/Function Specifies the entry number of phantom extension number which you are going to program. Reference •...
Page 255 Features Parameter Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the FDN (Floating Directory Number) for each Phantom button. Note • A single Phantom extension number can be assigned to multiple extensions so that the caller can ring a group of extensions simultaneously.
Page 256: Emergency Dial Code
Features 5.4 Emergency Dial Code Used to program a list of up to 10 emergency numbers that any extension in the system can dial at any time, regardless of dialing restrictions. Parameter Dial Default 1: 911, Others: Blank Value Range Up to 24 digits consisting of 0-9 Description/Function Specifies emergency telephone numbers that can be dialed from...
Page 257: Quick Dialing
Features 5.5 Quick Dialing Used to store up to eight Quick Dialing numbers. Parameter Dial Default All: Blank Value Range Up to 24 digits consisting of 0-9, , #, F, P, S or "-" (hyphen) Description/Function Specifies the phone number for Quick Dialing. Note •...
Page 258: Account Code
Features 5.6 Account Code Used to program a list of up to 1000 account codes which are used to identify incoming and outgoing CO calls for accounting and billing purposes. Parameter Tenant No. Default Value Range Description/Function Specifies the tenant to which a list of Account Codes is assigned. (Required when "Tenant Service"...
Page 259 Features Parameter Code Default Blank Value Range Up to 10 digits consisting of 0-9 Description/Function Specifies the account codes. Reference • 1.3 System Features (F/G) – Account Code Entry • 4.3.2 Account Code Entry (U/M) Parameter TRS Level Default None Value Range None, 1-6 Description/Function...
Page 260: Special Carrier Code
Features 5.7 Special Carrier Code Used to program a list of up to 100 Special Carrier Codes. Parameter Code Default Blank Value Range Up to 10 digits consisting of 0-9, , # or X Description/Function Specifies special carrier access codes. Notes •...
Page 261: Absent Message
Features 5.8 Absent Message Used to program a list of up to nine absent messages. An absent message, if set by the extension user, is displayed on the calling extension’s display PT to show the reason of absence (no answer). Parameter Message Default...
Page 262: Disa/Tie User Code
Features 5.9 DISA/TIE User Code Used to program a list of up to 32 DISA/TIE User Codes. Each code is appended with a COS level. Programming Guide...
Page 263 Features Parameter Code Default All: Blank Value Range 4-10 digits consisting of 0-9 Description/Function Specifies the User Codes for DISA/TIE feature. Warning for the Direct Inward System Access Users When you enable the CO-to-CO Line Call feature of Direct Inward System Access (DISA) function, if a third party discovers the password (a DISA User Code) of the system, you have a risk that they will make illegal phone calls using your telephone line, and the cost may be charged to your account.
Page 264: Vps Integration
Features 5.10 VPS Integration 5.10.1 VPS Integration 1/2 Used to assign Integration Code and Voice Mail Command for VPS Integration. Integration Code When DTMF tone Integration is activated, the KX-TD500 informs the VPS (Voice Processing System) of the status of the call (busy, answered, ringing, etc.) by sending a code with DTMF tone before sending the normal call progress tone (busy tone, ringback tone, etc.).
Page 265 Features Parameter [Integration Code] Busy Tone Default Value Range Up to 3 digits consisting of 0-9, or # Description/Function Specifies the Busy Tone code. Sent to the Voice Mail port when the extension dialed is busy. Reference • 1.3 System Features (F/G) –...
Page 266 Features Parameter [Integration Code] Extension Disconnection Default Value Range Up to 3 digits consisting of 0-9, or # Description/Function Specifies the Extension Disconnection code. Sent to the Voice Mail port when the caller disconnects. The Central Office must set a CPC signal to the PBX line for this signal to work for CO calls.
Page 267 Features Parameter [Integration Code] FWD to VM Busy Tone Default Value Range Up to 3 digits consisting of 0-9, or # Description/Function Specifies the FWD to VM Busy Tone code. Sent to the Voice Mail port when the extension dialed is forwarded to Voice Mail and no other Voice Mail ports are available to accept the call.
Page 268 Features Parameter [Voice Mail Command] Get Message Default Value Range Up to 16 digits consisting of 0-9, , # or H Description/Function Specifies the Get Message command. This command is transmitted to a VM port when the message receiver presses the MESSAGE button to retrieve a voice message. Reference •...
Page 269 Features 5.10.2 VPS Integration 2/2 Used to assign optional parameters for VPS Integration. Parameter DTMF signal duration Default 80 ms Value Range 80 ms 160 ms Description/Function Specifies the duration of the DTMF signals sent to the Voice Mail ports. Reference •...
Page 270 Features Parameter Pause timing before sending DTMF signal (Follow-on ID) Default 1.5 s Value Range 0.5 s 1.0 s 1.5 s 2.0 s Description/Function Specifies the length of time in seconds the system is to wait after Voice Mail port answers a call before sending DTMF signals (such as a mailbox number = Follow-on ID) to Voice Mail port.
Page 271 Features Parameter Start AA service after FWD, IRNA of CO call Default Do not start Value Range Do not start Start Description/Function Specifies whether the system starts the AA (Automated Attendant) Service or not when a CO call is directed to Voice Mail port by Call Forwarding or Intercept Routing.
Page 272 Features Parameter Sending out Follow-on ID after FWD Default Enable Value Range Disable Enable Description/Function Specifies whether or not the system sends Follow-on ID to a Voice Mail port after forwarding a call to the Voice Mail port. Reference • 1.3 System Features (F/G) –...
Page 273: Caller Id Modification
Features 5.11 Caller ID Modification Used to modify the telephone number sent from the Central Office by Caller ID Service to make up a telephone number for callback purposes. Parameter [Local Call] Area Code Default Blank Value Range Up to 6 digits consisting of 0-9 Description/Function Specifies the area code of the location where your KX-TD500 system is installed.
Page 274 Features Parameter [Local Call] Digits to delete Default No.1: 3, Others: 0 Value Range Description/Function Specifies the number of digits to be deleted from the telephone number (sent from the Central Office by Caller ID Service) to make up a telephone number for local call. Digits are removed from the beginning of the received digits.
Page 275 Features Parameter [Long Distance Call] Number to be added Default Value Range Up to 4 digits consisting of 0-9, or # Description/Function Specifies the number to be added to the telephone number (sent from the Central Office by Caller ID Service) to make up a telephone number for long distance call.
Page 276: Caller Id Registration
Features 5.12 Caller ID Registration 5.12.1 Caller ID Registration Used to assign the Caller ID code (identification code of the calling party) to utilize Caller ID Service provided by a specific Central Office (CO). If an ID Code transmitted from CO is found in the Caller ID Code Table, the caller's ID Code or a name given to the code is displayed on the display PT, allowing the called party to recognize the caller before answering a call.
Page 277 Features Operation Specify the Tenant No. in "5-12 Caller ID Registration" screen. • This determines the tenant no. of the System Speed Dial Data to be copied. Click on "5-12 Caller ID Registration" screen. • The message "W5022 Existing entries will be lost. Do you wish to continue?" is displayed.
Page 278 Features Parameter Name Default Blank Value Range Up to 16 characters consisting of 0-9, A-Z, a-z or the following marks: ! # $ % ( ) + , - / : ; < = > ? @ &. Description/Function Specifies the name to a Caller ID code. Note •...
Page 279: Ucd Time Table
Features 5.13 UCD Time Table If all extensions in a UCD group are busy, the incoming CO calls will be handled by the UCD Time Table procedure. Up to 32 UCD Time Tables, max.16 steps for each, can be assigned. Parameter Table No.
Page 280 Features Parameter Command Sequence (1-16) Default None Value Range None, S1 - S8, 1T - 4T, TR, RET, OFF Description/Function The following commands are provided to construct a UCD Time Table procedure. <Commands list and their functions> None: Skips to the next sequence. S1 - S8: OGM (1-8) is sent to the caller if available.
Page 281: Toll Restriction
Toll Restriction Section 6 Toll Restriction Programming Guide...
Page 282: Toll Restriction
Toll Restriction 6.1 Toll Restriction Used to assign TRS (Toll Restriction) Deny Codes and TRS Exception Codes. Programming Guide...
Page 283: Trs Deny Code
Toll Restriction 6.2 TRS Deny Code Used to program a list of up to 400 TRS (Toll Restriction) Deny Codes - telephone numbers that extension users cannot dial. Parameter TRS Level Default Value Range 2 - 6 Description/Function Specifies a TRS (toll restriction) level. Reference •...
Page 284 Toll Restriction Parameter Dial Default Blank Value Range Up to 10 digits consisting of 0-9, X, or # Description/Function Specifies the leading 10 digits of the toll-restricted telephone numbers. Note • "X" can be used as a wild card character which substitutes any digit in its position.
Page 285: Trs Exception Code
Toll Restriction 6.3 TRS Exception Code Used to program a list of numbers that an extension is allowed to dial, even if these numbers are listed in a TRS Deny Code Table. Up to 200 TRS Exception codes can be assigned. Parameter TRS Level Default...
Page 286 Toll Restriction Parameter Dial Default Blank Value Range Up to 10 digits consisting of 0-9, X, or # Description/Function Specifies the leading 10 digits of the telephone numbers which are excepted from the toll restriction. Note • "X" can be used as a wild card character which substitutes any digit in its position.
Page 287: Ars (Automatic Route Selection)
ARS (Automatic Route Selection) Section 7 ARS (Automatic Route Selection) Programming Guide...
Page 288: Ars (Automatic Route Selection)
ARS (Automatic Route Selection) 7.1 ARS (Automatic Route Selection) Used to assign ARS parameters. Programming Guide...
Page 289: Time Table
ARS (Automatic Route Selection) 7.2 Time Table Used to make up ARS time schedules. It is possible to split a day into four time zones (maximum) so that the least expensive line is selected for that time. Enter the starting time of each zone according to the service hours and charges offered by your carriers.
Page 290: Leading Digits Table
ARS (Automatic Route Selection) 7.3 Leading Digits Table Used to determine the appropriate Route Plan Table number for a call by analyzing the extension user-dialed number. Up to 800 Leading Digits entries can be programmed in the system. Parameter Entry No. Default 001-020 Value Range...
Page 291 ARS (Automatic Route Selection) Parameter Dial Default Blank Value Range Up to 10 digits consisting of 0-9, , # or X Description/Function Specifies the leading 10 digits of the telephone number which will be routed by ARS procedure. Note • "X" can be used as a wild card character which substitutes any digit in its position.
Page 292: Routing Plan
ARS (Automatic Route Selection) 7.4 Routing Plan Used to specify the Trunk Group number (1-48) and Modified Digit Table number (1-48) to be used for each route plan and time schedule. Up to 48 Routing Plan entries can be programmed in the system.
Page 293 ARS (Automatic Route Selection) Parameter [Time-A, -B, -C, -D] Modification Table No. Default None Value Range None, 1-48 Description/Function Specifies the MOD (Modified Digit) table (1-48) which is used to modify the user-dialed number so that it matches the requirements of the carrier.
Page 294: Digits Modification Table
ARS (Automatic Route Selection) 7.5 Digits Modification Table Used to modify the user-dialed number so that it matches the requirements of the carrier. Up to 48 Digits Modification entries can be programmed in the system. Parameter Entry No. Default 01-08 Value Range 01-48 in 8 entries increments Description/Function...
Page 295 ARS (Automatic Route Selection) Parameter Number to be added Default Blank Value Range Up to 20 digits consisting of 0-9, , # or P [Pause] Description/Function Specifies the dialing number to be added to the beginning of the user-dialed number. Reference •...
Page 296 ARS (Automatic Route Selection) Programming Guide...
Page 297: Private Network
Private Network Section 8 Private Network Programming Guide...
Page 298: Private Network
Private Network 8.1 Private Network Used to assign parameters required to utilize TIE line service. Programming Guide...
Page 299: Tie Routing Table
Private Network 8.2 TIE Routing Table Used to specify trunk groups and parameters required for making TIE calls. This table is referenced by the system to identify the trunk route, when an extension user made a TIE call by dialing the feature number for "TIE Line Access" or "Other PBX 01-16." The first 3 digits (other than TIE Line Access Code) of the dialed number decide a routing pattern appropriate for each call.
Page 300 Private Network Parameter Leading Digit Default Blank Value Range Up to 3 digits consisting of 0-9 or X Description/Function Specifies the leading one, two or three digits of the number for TIE calls. Used to determine the trunk group for routing a TIE call. Note •...
Page 301: Did Dial
DID Dial Section 9 DID Dial Programming Guide...
Page 302: Did Dial
DID Dial 9.1 DID Dial Used to assign parameters required to utilize DID/MDN service. Programming Guide...
Page 303: Did Dial Registration
DID Dial 9.2 DID Dial Registration 9.2.1 DID Dial Registration Used to specify several parameters for DID/MDN service. Parameter Entry No. Default 0001-0010 Value Range 0001-1000 in 10 entries increments Description/Function Specifies the entry number of DID/MDN No. which you are going to program.
Page 304 DID Dial Parameter DID/MDN No. Default Blank Value Range Up to 16 digits consisting of 0-9 Description/Function Specifies the DID/MDN number which will be sent from the Central Office to the KX-TD500 system. Note • The DID/MDN number which has already been assigned cannot be registered.
Page 305 DID Dial Parameter Destination – Day/Night Default Blank Value Range 3-4 digits consisting of 0-9 Description/Function Specifies the DN/FDN (Extension Group, TAFAS, Phantom Extension, Remote Resource, OGM Group, Incoming Group) and the other PBX extension numbers where a DID call comes in during Day/Night mode respectively.
Page 306 DID Dial 9.2.2 Automatic Registration of DID/MDN Numbers Provides quick registration of DID/MDN numbers. Up to 100 entries can be registered at once with a simple operation. 1. Click on "9-1 DID Dial Registration" screen. • "Automatic Registration" screen is displayed. 2.
Page 307 DID Dial 3. Click • The following DID/MDN numbers are registered in Entry Nos. 1–100 of "DID/MDN No." automatically. Programming Example: Entry No.1: 123456 (00) Entry No.2: 123456 (01) Entry No.3: 123456 (02) • • • • Entry No.99: 123456 (98) Entry No.100: 123456 (99) Notes •...
Page 308 DID Dial Parameter [Additional Number] Number of Registrations Default 10 entries Value Range 10-100 entries in 10 entries increments Description/Function Specifies the number of DID/MDN entries to be registered automatically. Reference None Parameter [Additional Number] Number of Digits Default 2 digits (00-99) Value Range 1-16 digits Description/Function...
Page 309: Maintenance
Maintenance Section 10 Maintenance Programming Guide...
Page 310: Maintenance
Maintenance 10.1 Maintenance Used to assign parameters for system maintenance. Programming Guide...
Page 311: External Modem 1/2
Maintenance 10.2 External Modem 1/2 The system supports an external modem plugged into the RS-232C port for remote system administration. Parameter Manual Initialization Command (1- 5) Default All: Blank Value Range Up to 80 characters consisting of 0-9, A-Z, a-z or the following marks: ! # $ % ( ) + , - / : ;...
Page 312 Maintenance Parameter Automatic Initialization Command Default AT&F0Q0E0V1S0=1X0&D0 Value Range Up to 80 characters consisting of 0-9, A-Z, a-z or the following marks: ! # $ % ( ) + , - / : ; < = > ? @ &. Description/Function Specifies Modem Automatic Initialization Command.
Page 313: External Modem 2/2
Maintenance 10.3 External Modem 2/2 Parameter Connection Message (1-5) Default Message 1: CONNECT, Others: Blank Value Range Up to 80 characters consisting of 0-9, A-Z, a-z or the following marks: ! # $ % ( ) + , - / : ; < = > ? @ &. Description/Function Specifies Connection Message from Modem.
Page 314: Smdr
Maintenance 10.4 SMDR 10.4.1 SMDR 1/2 Station Message Detail Recording (SMDR) automatically records detailed information for outside calls. Parameter SMDR Connection Default Value Range Description/Function Enables or disables SMDR. Reference • 2.8.3 Personal Computer/Printer (I/M) Programming Guide...
Page 315 Maintenance Parameter Output Type Default Type-A Value Range Type-A Type-B Description/Function Specifies the output type of SMDR Printout. For further information, please refer to "Station Message Detail Recording (SMDR)" of Section "1.3 System Features" in the Features Guide. You can also get information on "Output Type" by clicking on this screen.
Page 316 Maintenance Parameter [Format] Skip Perforation Default Value Range 0-95 lines Description/Function Determines the number of lines to be skipped at the end of every page. The number of lines to skip is simply the number specified in this parameter. The number of lines printed is the difference between the Page Length number and the Skip Perforation number.
Page 317 Maintenance Parameter Print out Caller ID Information Default Number Value Range Number Name Disable Description/Function SMDR can print out Caller ID information. This setting specifies whether priority is given to Caller ID Name or to Caller ID Number. Reference • 1.3 System Features (F/G) –...
Page 318 Maintenance Parameter Print out Timed Reminder Information Default Disable Value Range Enable Disable Description/Function If this is enabled, SMDR will print out "Timed Reminder / Start" each time the timed reminder alarm starts ringing. In addition, if it is answered, SMDR will print out "Timed Reminder / Answer," and if it is not answered, SMDR will print out "Timed Reminder / No Answer."...
Page 319 Maintenance Parameter Time Display Mode Default Value Range Description/Function Specifies the time display mode, 12-hour or 24-hour notation, which will be printed out by SMDR. Reference • 1.3 System Features (F/G) –Station Message Detail Recording (SMDR) 10.4.2 SMDR 2/2 Station Message Detail Recording (SMDR) automatically records detailed information for outside calls.
Page 320: Power Failure Transfer
Maintenance 10.5 Power Failure Transfer Power Failure Transfer connects specific telephones (any SLT and a certain type of APT) to pre-determined CO lines in the event of system power failure. Parameter Trunk Card (1-24) Default None Value Range None, XXX: YYY [XXX: Card No. (101-314), YYY: Card Type] Description/Function Specifies the trunk card number and its type, which will be used in case of Power Failure Transfer.
Page 321 Maintenance Parameter Extension Card (1-24) Default None Value Range None, XXX: YYY [XXX: Card No. (101-314), YYY: Card Type] Description/Function Specifies the extension card number and its type, which will be used in case of Power Failure Transfer. Notes • DPTs and some APTs cannot be used during a power failure. •...
Page 322: System Parameters
Maintenance 10.6 System Parameters Used to assign various system parameters. Passwords for System Programming by PC Required to perform the System Programming and Maintenance in the interactive mode using the Maintenance Console software from a PC (Personal Computer). There are four passwords for System Programming by PC.
Page 323 PC and check the Password with programming screen. • If you don't have the backup system data, you have to program again or contact your Panasonic dealers. The higher the password level (level 1 is the highest) is, the more programming items the...
Page 324 Maintenance Parameter [Password] System Programming – Protection Level 1 Default 1234 Value Range 4-7 digits of alphanumeric characters Description/Function Specifies the password required for entering the System Programming and Maintenance mode from a PC (Personal Computer). Reference • 3.5 Operational Mode (I/M) •...
Page 325 Maintenance Parameter [Password] User Programming – PT Default 1234 Value Range 4-7 digits consisting of 0-9 Description/Function Specifies the password required for entering the User Programming mode by PT. Reference • 1.2 System Administration (F/G) – User Programming with Proprietary Telephone •...
Page 326 Maintenance Parameter [Serial Interface Port] PROG – NL Code Default CR + LF Value Range CR+LF Description/Function Specifies the NL (New Line) Code for your printer or personal computer. If your printer or personal computer automatically feeds lines with a carriage return, select "CR (Carriage Return)." If not, select "CR+LF (Line Feed)."...
Page 327 Maintenance Parameter [Serial Interface Port] PROG – Baud Rate Default 9600 bps Value Range 2400 bps 4800 bps 9600 bps 19200 bps Description/Function Specifies the data transmission speed from the system to the printer or personal computer. Reference None [Serial Interface Port] SMDR (Port 2) Please refer to "Station Message Detail Recording (SMDR)"...
Page 328 Maintenance Parameter [Serial Interface Port] SMDR – NL Code Default CR + LF Value Range CR+LF Description/Function Specifies the NL (New Line) Code for your printer or personal computer. If your printer or personal computer automatically feeds lines with a carriage return, select "CR (Carriage Return)." If not, select "CR+LF (Line Feed)."...
Page 329 Maintenance Parameter Remote FDN Default 1499 Value Range Up to 4 digits consisting of 0-9 Description/Function Specifies the FDN (Floating Directory Number) for Remote Administration. Reference • 1.2 System Administration (F/G) – System Programming and Diagnosis with Personal Computer • 3.4.3 Remote Administration (Remote Connection) (I/M) Parameter DN Refer Default...
Page 330: System Time
Maintenance 10.7 System Time Used to assign System Time. For information on the default values of summer time, please refer to the table on the Page 331. Programming Guide...
Page 331 Maintenance Default values of summer time Start 2001 2001 2002 2002 2003 2003 2004 2004 2005 2005 2006 2006 2007 2007 2008 2008 2009 2009 2010 2010 2011 2011 2012 2012 2013 2013 2014 2014 2015 2015 2016 2016 2017 2017 2018 2018...
Page 332 Maintenance System Time Parameter (Year) Default Value Range 00-99 Description/Function Specifies the last two digits of the year by entering the value directly. Reference 1.8 Ringing Features (F/G) – Timed Reminder (Wake-Up Call) – Timed Reminder, Remote (Wake-Up Call) 1.17 Display Features (F/G) –...
Page 333 Maintenance Parameter (Day of the week) Default Value Range Sun - Sat Description/Function Selects the day of the week by clicking the small triangle. Reference 1.8 Ringing Features (F/G) – Timed Reminder (Wake-Up Call) – Timed Reminder, Remote (Wake-Up Call) 1.17 Display Features (F/G) –...
Page 334 Maintenance Parameter (AM / PM) Default Value Range AM / PM Description/Function Selects AM / PM by clicking the small triangle. Reference 1.8 Ringing Features (F/G) – Timed Reminder (Wake-Up Call) – Timed Reminder, Remote (Wake-Up Call) 1.17 Display Features (F/G) –...
Page 335 Maintenance Parameter End (Month) Default Please refer to "Default values of summer time." Value Range Jan-Dec Description/Function Selects the month by clicking the small triangle. Reference None Parameter Start (Day) Default Please refer to "Default values of summer time." Value Range 01-31 Description/Function Specifies the date in two digits by entering the value directly.
Page 336 Maintenance Programming Guide...
Page 337: Programming Error Messages
Programming Error Messages Section 11 Programming Error Messages Programming Guide...
Page 338: Error Messages (Exxxx)
Programming Error Messages 11.1 Error Messages (EXXXX) Error Message Error Code Description E0000 System error. (Error code: XXX) A system error occurred. Please inform your distributor how the error was generated and what the error code was. E0001 Cannot create temporary file. There is insufficient free space on your hard disk or this software is not installed correctly.
Page 339 Programming Error Messages Error Message Error Code Description E0012 Another maintenance device is connected. There are three ways to access the PBX: (1) By PC System Programming, (2) by Remote System Programming, or (3) by User Programming. But only one at a time. E0013 Please reconnect after the PBX becomes on-line or off-line completely.
Page 340 Programming Error Messages Error Message Error Code Description E1006 You have exceeded the system limit of AGC cards. There is a limit of 8 AGC cards per system. E1007 You have exceeded the system limit of remote cards. One RMT card or one ERMT card can be installed in the system -- only one. E1008 You have exceeded the system limit of DPH cards.
Page 341 Programming Error Messages Error Message Error Code Description E1023 Assign the directory numbers for EXT#1 and EXT#2. For the VPS port you must assign directory numbers for both voice mail numbers, EXT#1 and EXT#2. These cannot be assigned individually. E1024 Cannot assign the port which does not have VPS (DPT) attribute.
Page 342 Programming Error Messages Error Message Error Code Description E1037 Cannot change the status of the port. Cannot change the status of the SLT port because the PT port is activated as a "Parallel Mode" extension. Please change the PT port status to "XDP Mode" and then press "Apply."...
Page 343 Programming Error Messages Error Message Error Code Description E2005 Maximum entry number of System Speed Dialing exceeded. The system provides up to 1000 / tenant, 2000 / system of System Speed Dialing entries available to all extension users. E2006 Cannot change System Speed Dialing Entries Maximum. Please delete System Speed Dialing entries until there is less than the setting you want.
Page 344 Programming Error Messages Error Message Error Code Description E3004 Extension group number duplicated. Each extension group in the same paging group must have a unique number. E3005 The extension group already belongs to another paging group. An extension group cannot belong to two or more paging groups. E3006 Invalid directory number for Incoming group destination.
Page 345 Programming Error Messages Error Message Error Code Description E4013 Cannot assign SDN key without assigning PDN key. An SDN button should have its associated PDN button. E4014 Cannot assign more than 8 SDN keys for one PDN key. Up to eight SDN keys per PDN key can be assigned on eight different PTs respectively. E4015 Invalid directory number for SDN key.
Page 346 Programming Error Messages Error Message Error Code Description E4026 Please enter CO key number assigned to S-CO, G-CO, L-CO or SDN key. The CO key number which is assigned to Single-CO, Group-CO, Loop-CO or SDN key should be entered when "Prime Line - CO" is specified in "[Preferred Line] Outgoing / Incoming"...
Page 347 Programming Error Messages Error Message Error Code Description E5010 Specify the code. The account code also must be entered when the TRS Level is assigned and the TRS Level also must be deleted when the account code is deleted. E5011 Specify the leading digits.
Page 348 Programming Error Messages Error Message Error Code Description E9007 Invalid User Programming password. Please assign the 4 through 7-digit User Programming password consisting of 0–9. E9008 Invalid Walking COS password. Please assign the 4 through 7-digit Walking COS password consisting of 0–9. E9009 DID / MDN number duplicated.
Page 349: Warning Messages (Wxxxx)
Programming Error Messages 11.2 Warning Messages (WXXXX) Message Code Description W0001 Save system data? Some parameters on the screen were changed. A click on "OK" or a screen switch was attempted without saving data. W0002 The status of the port is In-Service (INS). Would you like to continue? When the status of a port is In-Service (INS), and you change some parameters (screens of "1 Configuration"), the port is reset.
Page 350 Programming Error Messages Message Code Description W4002 Extension name must not exceed 10 characters. Truncate it? Truncate means that the leading 10 characters are saved and the rest are deleted. W4003 One-Touch dial number must not exceed 24 digits. Truncate it? Truncate means that the leading 24 digits are saved and the rest are deleted.
Page 351 Programming Error Messages Message Code Description W5013 Caller ID name must not exceed 16 characters. Truncate it? Truncate means that the leading 16 characters are saved and the rest are deleted. W5014 Caller ID number must not exceed 24 digits. Truncate it? Truncate means that the leading 24 digits are saved and the rest are deleted.
Page 352: Information Message (Ixxxx)
Programming Error Messages 11.3 Information Message (IXXXX) Message Code Description I0001 Upload completed. Please change PBX to on-line mode. Uploading the system programming data from PC to PBX is completed. How to change PBX to on-line mode: 1. Set CPU Mode Rotary-Switch position to 0. 2.
Page 353: Default Values
Default Values Section 12 Default Values Programming Guide...
Page 354 Default Values 1 Configuration 1.1 Configuration 1.2 Slot Assignment 1.2.1 Slot Assignment Program Default Card Type Blank Status — 1.2.2 Card Properties (HLC/SLC/OPX/SLC-M) Program Default % Break Detection 16-96 ms Flash Detection 1.2.3 Card Properties (DHLC/ESLC/DLC) Program Default % Break Detection 16-96 ms Flash Detection LPR Version...
Page 355 Default Values 1.2.5 Card Properties (ELCOT) Program Default First Dial Timer 1.0 s % Break Flash Time 608 ms Pulse Feedback Tone Caller ID — Inter-digit Pause 830 ms Pulse Break Time Adjustment 0 ms Bell Detection Time 144 ms DTMF Inter-digit Pause Time 112 ms Bell Disappearance Timer...
Page 356 Default Values Program Default Pulse Feedback Tone Signaling Bit Monitor (Port No.) Disable Signaling Bit Monitor (Mode) Mode 3 Software Information (Display only) Inter-digit Pause 830 ms Flash Detection Flash Detection Timer 208-1016 ms Answer Decision Timer 32 ms % Break Detection 16-96 ms Transmission of RAI 1.2.8 Card Properties (BRI)
Page 357 Default Values Program Default Blank 1.2.10 Card Properties (PRI23) Program Default Network Type (Display only) Status Message Enable Status Receive Disconnect [DTMF Signal] Duration 80 ms [DTMF Signal] Inter-digit Pause 112 ms Line Coding B8ZS Frame Sequence Extended Superframe (ESF) Software Information (Display only) Timer Setting...
Page 358 Default Values Program Default [CO/Qsig-Master(PRI only)/Qsig-Slave(PRI 0 s (BRI), 30 s (PRI23) only)] T304 [CO/Qsig-Master(PRI only)/Qsig-Slave(PRI 30 s only)] T305 [CO/Qsig-Master(PRI only)/Qsig-Slave(PRI 30 s (BRI), 0 s (PRI23) only)] T306 [CO/Qsig-Master(PRI only)/Qsig-Slave(PRI 0 s (BRI), 30 s (PRI23) only)] T310 [CO/Qsig-Master(PRI only)/Qsig-Slave(PRI 10 s (BRI), 30 s (PRI23) only)] T3D3...
Page 359 Default Values 1.2.13 Card Properties (ERMT) Program Default Baud Rate (Modem Speed) 33600 bps 1.2.14 CPU Card Information Program Default Software Version (Display only) Area Code (Display only) 1.2.15 TSW Card Configuration Program Default [Option Card Status] Conference Expansion Card (Display only) [Option Card Status] Digital OHCA Card (Display only) System Clock Status...
Page 360 Default Values Program Default Group No. Parallel / XDP (DHLC card) Parallel Parallel / XDP (HLC card) None Status — DN Refer — 1.5 VPS (DPT) Port Assignment Program Default TVS No. VPS Card None Type None Jack No. (Display only) Port No.
Page 361 Default Values 1.7 DISA Port Assignment Program Default [Card No. 1-8] Location (Display only) [Card No. 1-8] OGM Group No. 1.8 BRI Port Assignment Program Default Card No. — Type Blank Group No. Status — DN Refer — 1.9 PRI Port Assignment Program Default Card No.
Page 362 Default Values Program Default Inter-tenant Calling (1 - 8) No check (Auto Start Time) Day (SUN-SAT) 9:00 AM Night (SUN-SAT) 5:00 PM Lunch-Start (SUN-SAT) 12:00 PM Lunch-End (SUN-SAT) 1:00 PM Break-Start (SUN-SAT) 3:00 PM Break-End (SUN-SAT) 3:30 PM Music on Hold Source MUS1 BGM Source MUS1...
Page 363 Default Values Program Default 17 Operator Call 18 Local CO Line Access / ARS 19 Trunk Group Access 20 Speed Dialing - System 21 Speed Dialing - Station 22 Speed Dialing - Station Programming 23 Doorphone Call 24 External Paging 25 External Paging Answer / TAFAS Answer 26 Station Paging 27 Station Paging Answer...
Page 364 Default Values Program Default 48 Absent Message Set / Cancel 49 Timed Reminder Confirm / Set / Cancel 50 Station Lock Set / Cancel 51 Night Mode Set / Cancel 52 Parallel Telephone Mode 53 External BGM On / Off 54 Live Call Screening 55 Call Log Incoming, Overwrite Mode 56 Call Log Incoming, Log Lock...
Page 365 Default Values Program Default 101 COS Secondary 102 Reserved (Reserved for future use.) Blank 103 Group Login / Logout 104 Group FWD 105-120 Reserved (Reserved for future use.) Blank 2.4 Class of Service (COS) 2.4.1 Class of Service (COS) 1/2 Program Default COS No.
Page 366 Default Values 2.4.2 Trunk Group Setting Program Default Trunk Group No. 01-48 – Day / Night All: Check 2.4.3 Class of Service (COS) 2/2 Program Default Secret Busy Override Disable Transferring CO dial tone (exempted from TRS) Enable Transfer to TIE Disable Incoming Group FWD Disable...
Page 367 Default Values Program Default DISA Prolong Time 3 min DISA Delayed Answer Time 1 ring Timed Reminder Arrive Count 3 times DISA Automated Attendant Time DISA IRNA Time 60 s Intercept Timer after OGM Auto Shut-off Time 15 s Timed Reminder Arrive Wait Time 60 s Intercept Time Day: 12 rings, Night/Lunch/Break: 0 ring...
Page 368 Default Values Program Default 8. Confirmation tone for Override, Barge-in, Enable Conference and Privacy Release 9. Confirmation tone for Call Pickup, Paging, Enable Paging- Answer, TAFAS-Answer, Hold Retrieve and Call Park Retrieve 10. Station Speed Dialing Initial display Name 2.8.2 System Option 2 Program Default 11.
Page 369 Default Values Program Default 30. Net CODEC Mu Law 2.8.4 System Option 4 Program Default 31. Answering Call Waiting call by SLT hooking Disable 32. Whisper OHCA to extensions other than Disable T74XX 33. FWD / DND lamp pattern FWD: Flash, DND: On 34.
Page 370 Default Values 2.8.6 System Option 6 Program Default 61. Auto Answer with held call Disable 63. VM Trunk Service for DID Disable 64. CNIP Service Disable 65. Alert Ringing Disable 67. Sending DID Number to VPS Disable 2.9 PRI Originating Control Program Default PRI Inter-digit Timer-1...
Page 371 Default Values Program Default PBX Access Code Blank [Numbering Plan ID] Outgoing—Public Default [Numbering Plan ID] Outgoing—Private Private [Numbering Plan ID] Incoming—Public Default [Numbering Plan ID] Incoming—Private Private PBX Dial Tone Disable PBX Ringback Tone Disable [Type of Number] Outgoing—Public Default [Type of Number] Outgoing—Private Default...
Page 372 Default Values Program Default FWD / DND Mode Enable Extension Call Hunting Enable Calls to Empty Group Disable [UCD Setting] Time Table No. None [UCD Setting] FWD No Answer Disable [UCD Setting] Auto LOGOUT Mode Disable [UCD Setting] Supervisor Extension Blank [UCD Setting] LOGIN Monitor Disable...
Page 373 Default Values Program Default Calls to Empty Group Disable [UCD Setting] Time Table No. None [UCD Setting] FWD No Answer Disable [UCD Setting] Auto LOGOUT Mode Disable [UCD Setting] Supervisor Extension Blank [UCD Setting] UCD Call Waiting Enable [Operator Setting] Call Priority CO Call: 1, Intercept Routing: 2, Recall: 3, Extension Call: 4 [Operator Setting] Ringing Type...
Page 374 Default Values 4 Line 4.1 Line 4.2 Trunk Line Program Default Card No. — Port No. Copy — Group No. (Display only) Name CO001-CO192 Incoming Type (1) DIL: ELCOT/GCOT/LCOT/T1 [GCO]/T1 [LCO] card (2) DID: DID/T1 [DID] card (3) DID (ISDN): BRI/PRI23 card (4) TIE: T1 [TIE] card Dial Type DTMF-80: ELCOT/GCOT/LCOT/T1/DID card,...
Page 375 Default Values 4.3 Extension Line 4.3.1 Extension Line 1/2 Program Default Card No. — Port No. — Group No. (Display only) Copy — Name Blank Message Lamp Mailbox No. Same as the extension number CO Key — PF Key — Initial Display Selection Caller ID [COS No.] Primary...
Page 376 Default Values Program Default JOG Dial Speed Normal [CLIP Number] Public Blank [CLIP Number] Private Blank [Call Log Incoming] Overwrite Mode [Call Log Incoming] Lock Password Blank 4.3.2 Flexible CO Key Assignment Program Default Key Type CO-01: Loop-CO, Others: Not Stored 4.3.3 Flexible PF Key Assignment for PT Program Default...
Page 377 Default Values 4.4.1 Flexible DSS Key Assignment Program Default Key Type Not Stored 4.4.2 Flexible PF Key Assignment for DSS Console Program Default Key Type Not Stored 4.5 Doorphone Program Default Card No. — Port No. Tenant No. Destination – Day / Night Blank 4.6 External Paging Program...
Page 378 Default Values Program Default Tone Enable ISDN Bearer Mode Automatic Numbering Plan ID Default Type of Number Default [CLIP Number] Public Blank [CLIP Number] Private Blank [COS No.] Primary [COS No.] Secondary 5 Features 5.1 Features 5.2 System Speed Dialing Program Default Tenant No.
Page 379 Default Values 5.5 Quick Dialing Program Default Dial All: Blank 5.6 Account Code Program Default Tenant No. Entry No. 0001-0020 Code Blank TRS Level None 5.7 Special Carrier Code Program Default Code Blank 5.8 Absent Message Program Default Message MSG1: Will Return Soon, MSG2: Gone Home, MSG3: At Ext %%%% (Extension No.), MSG4: Back at %% : %% (Hour: Minute), MSG5: Out Until %% / %% (Month / Day), MSG6: In a Meeting,...
Page 380 Default Values 5.10 VPS Integration 5.10.1 VPS Integration 1/2 Program Default Integration Code [Integration Code] Ringback Tone [Integration Code] Busy Tone [Integration Code] Reorder Tone [Integration Code] DND Tone [Integration Code] Extension Answer [Integration Code] Extension Disconnection [Integration Code] Confirmation Tone [Integration Code] FWD to VM Ringback Tone [Integration Code] FWD to VM Busy Tone [Integration Code] FWD to Extension Ringback...
Page 381 Default Values Program Default Sending out Follow-on ID after FWD Enable Sending out Follow-on ID after IRNA Disable 5.11 Caller ID Modification Program Default [Local Call] Area Code Blank [Local Call] Digits to delete No.1: 3, Others: 0 [Local Call] Number to be added Blank [Long Distance Call] Digits to delete [Long Distance Call] Number to be added...
Page 382 Default Values 6 Toll Restriction 6.1 Toll Restriction 6.2 TRS Deny Code Program Default TRS Level Entry No. 001-020 Dial Blank 6.3 TRS Exception Code Program Default TRS Level Entry No. 001-020 Dial Blank 7 ARS (Automatic Route Selection) 7.1 ARS (Automatic Route Selection) 7.2 Time Table Program Default...
Page 383 Default Values 7.4 Routing Plan Program Default Plan No. [Time-A, -B, -C, -D] Trunk Group No. None [Time-A, -B, -C, -D] Modification Table No. None 7.5 Digits Modification Table Program Default Entry No. 01-08 Digits to delete Number to be added Blank 8 Private Network 8.1 Private Network...
Page 384 Default Values Program Default Automatic Registration — DID/MDN No. Blank Tenant No. VPS Trunk Group No. Destination – Day/Night Blank Name Blank 9.2.2 Automatic Registration of DID/MDN Numbers Program Default [Base Number] Dial Blank [Additional Number] Number of Registrations 10 entries [Additional Number] Number of Digits 2 digits (00-99) Beginning Entry No.
Page 385 Default Values 10.4 SMDR 10.4.1 SMDR 1/2 Program Default SMDR Connection Output Type Type-A Print out Error Information Disable [Format] Page Length 24 lines [Format] Skip Perforation [Duration Log] Outgoing Calls [Duration Log] Incoming Calls Print out Caller ID Information Number Print out DID Information Disable...
Page 386 Default Values 10.6 System Parameters Program Default [Password] System Programming – Protection 1234 Level 1 [Password] System Programming – Protection 1234 Level 2 [Password] System Programming – Protection 1234 Level 3 [Password] System Programming – Protection 1234 Level 4 [Password] User Programming – PT 1234 [Password] Walking COS 1234...
Page 387 Default Values Program Default (Month) (Day) (Day of the week) (Hour) (Minute) (AM / PM) Summer Time / Daylight-saving Time Setting Setting Disable Start (Month) Please refer to "Default values of summer time." End (Month) Please refer to "Default values of summer time." Start (Day) Please refer to "Default values of summer time."...
Page 388 Copyright: This manual is copyrighted by Panasonic Communications Co., Ltd. (PCC). You may print out this manual solely for internal use with this model. Except above, you may not reproduce this manual in any form, in whole or part, without the prior written consent of PCC and its licensee.

Panasonic LX-TD500 Programming Manual

Quick Links

Related Manuals for Panasonic LX-TD500

Summary of Contents for Panasonic LX-TD500

Table of Contents