Page 1
Introduction For more information — EZClean Compressed air The EZClean compressed air supply unit is a rugged, Publications for the associated AWT420 transmitter supply unit reliable cubicle that delivers compressed air to an and ADS420 optical dissolved oxygen probe are...
This symbol indicates the need for protective hand Electrical – high voltage wear. The EZClean air compressor unit requires a 230 or 115 V AC mains supply to operate. A mains isolation switch must be Recycle separately from general waste under the fitted in the supply to the unit.
Health and Safety …1 Product recycling and disposal (Europe only) ABB is committed to ensuring that the risk of any environmental damage or pollution caused by any of its products is minimized as far as possible. The European Waste Electrical and Electronic...
E Z C L E A N | C O M P R E S S E D A I R S U P P LY U N I T | O I/ E ZC L E A N - E N R E V. A System overview EZClean components are shown in Figure 1 shows the EZClean compo: Figure 1 EZClean components...
E Z C L E A N | C O M P R E S S E D A I R S U P P LY U N I T | O I/ E ZC L E A N - E N R E V. A Handrail/wall-mounting This procedure is for handrail/wall-mounting using the optional Referring to Figure 3:...
E Z C L E A N | C O M P R E S S E D A I R S U P P LY U N I T | O I/ E ZC L E A N - E N R E V. A …3 Installation Pole-mounting Referring to Figure 4:...
Referring to Figure 5: 1 Connect one end of the 6 mm OD nylon tubing bulkhead push-fit connector Figure 6 Connecting 6 mm OD nylon tubing to the ABB compressed air adaptor 3 Proceed to "Electrical connections" on page 10 to make electrical connections.
E Z C L E A N | C O M P R E S S E D A I R S U P P LY U N I T | O I/ E ZC L E A N - E N R E V. A …4 Connections Electrical connections Relay connections...
– see "Sensor 2 Ensure pneumatic connections are made between the Setup" on page 12: EZClean compressed air unit and an ABB compressed air S1(to 2) :DO adaptor to be fitted on the sensor. 3 Ensure electrical connections are made between the EZClean PV Type compressed air unit and the AWT420 transmitter –...
E Z C L E A N | C O M P R E S S E D A I R S U P P LY U N I T | O I/ E ZC L E A N - E N R E V. A …5 Configuration Sensor Setup Used to set the tag, measurement units, operational range and clean functions and to...
E Z C L E A N | C O M P R E S S E D A I R S U P P LY U N I T | O I/ E ZC L E A N - E N R E V. A 6 Maintenance Annual maintenance 1 Ensure compressed air supply unit mountings are secure.
E Z C L E A N | C O M P R E S S E D A I R S U P P LY U N I T | O I/ E ZC L E A N - E N R E V. A Specifications Compressed air unit Environmental ratings...
4 × handrail/wall mounting plates, 2 × extension – 15 m (45 ft) × 6 mm OD nylon tubing plates, U-bolts, nuts and washers – G3/8 push-fit connector EZClean compressor unit – 230 and 115 V AC EZClean compressor pneumatic fittings kit Part number Description...
Page 16
We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.