Page 1
Please follow the information provided in this section to perform the complete disassembly procedure of the Notebook. Be sure to use proper tools described before. SUS FX505DY series notebook consists of various modules. This chapter describes the procedure for the complete notebook disassembly and assembly (Assemble document please look up from the last page).
Disassembly Procedure Service Overview Please pay special attention to the cautions below to prevent any damages to the notebook and also please be sure to select the appropriate tools described in this section to perform any services desired. Precautions Before you perform any service and or repair on the notebook, please follow the steps below first. 1.
Page 3
Disassembly Procedure If the screws have the following damaged appearance, please do not use. a. Shape deformed b. Paint scratched off c. Rusty d. Damaged head – unable to drive in e. Damaged unable to securely tighten BACK 2 - 3 V1.0...
Page 4
Disassembly Procedure Appropriate Tools The illustrations below show the appropriate tools that should be used for the notebook’s service and repair. Cross Screwdriver Please according to different screw specification and choose different screwdriver and head. Below photos are for reference only. Use a cross screwdriver to fasten/remove screws.
Page 5
Disassembly Procedure Thickness gauge (PN: 20LT0-0002J000) Thickness compass specification 0.05mm-1.5mm Use it to measure the gap. Hand rollers (PN: 20LT0-00082000,order or local buy) Use the roller to press touch pad mylar. BACK 2 - 5 V1.0...
Page 6
Disassembly Procedure Bottom case Module The illustration below shows how to remove the bottom case module. 1. Remove 11 pcs screws on the bottom case. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 3kgf-cm 13050-B2813000 *6 13GMBKXD061Z-1 *5 13GMBKXD061Z-1:...
Disassembly Procedure Battery Module The illustration below shows how to remove the battery module. 1. Disconnect the connector at PCB end. 2. Remove 1 screws on battery module. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 3kgf-cm 13GMBKXD061Z-1: SCREW M2.5*6L (4.6,0.85) (K) B-ZN NY...
Page 9
Disassembly Procedure The illustration shows how to remove the HDD. 1. Remove 2 screws on HDD. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 3kgf-cm 13GMBKXD061Z-1: SCREW M2.5*6L (4.6,0.85) (K) B-ZN NY #1 2. Disconnect HDD. 3.
Page 10
Disassembly Procedure The illustrations below show how to remove the SSD. 1. Remove a screw from SSD. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0kgf-cm 13GMBK3C036Z-1: SCREW M2*3L (4.6,0.8) (K) B-ZN NY #1 2 - 10 V1.0...
Page 11
Disassembly Procedure Notice: Add KB BL TAPE. Alignment 13NR01A0L08011 FX505DY SSD ABSORBER Notice: Add SSD AL FOIL. 13NR00S0L83021 FX505GE SSD AL FOIL BACK 2 - 11 V1.0...
Disassembly Procedure Memory Module The illustration shows how to remove the Memory. 1. Tear off the Mylar and remove the memory. 13NR00S0L43011 BACK 2 - 13 V1.0...
Page 14
Disassembly Procedure Thermal and Fan Module The illustration below shows how to remove the Thermal and fan module. 1. Remove 13 screws on the thermal module and take it away. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0kgf-cm 13GMBK3C045W-1: SCREW M2*4.5L (4.5,0.8) (K) W-NI NY #1...
Page 15
Disassembly Procedure Notice: Add MB TOP CU FOIL. 13NR01A0M02011 FX505DY MB TOP CU FOIL 2 - 15 V1.0...
Page 16
Disassembly Procedure 13NR00S0M10011 Assemble Notice: After replace new MB, please clean remaining CPU and GPU thermal pad on thermal module and then paste new one. Please use the correct technique of taking fans in order to avoid being out of shape BACK 2 - 16 V1.0...
Disassembly Procedure Main Board The illustrations below show how to remove the main board. 1. Disconnect eDP/FFC/Touchpad FFC/Speaker cable/DC IN cable from MB. a. Remove KB FFC. b. Remove touchpad FFC. c. Remove KB FFC. 2 - 17 V1.0...
Page 18
Disassembly Procedure d. Disconnect EDP cable. e. Disconnect speaker cable. f. Disconnect DC jack cable. 2 - 18 V1.0...
Page 19
Disassembly Procedure 2. Remove 5 screws on MB. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0kgf-cm 13GMBK3C036Z-1: SCREW M2* 3L (4.6,0.8) (K) B-ZN NY #1 3. Remove LED FFC from MB. 2 - 19 V1.0...
Disassembly Procedure LED Board The illustration below shows how to remove the LED board. 1. Disconnect LED FFC and remove LED board & mylar & Sponge. FX505GE TOP LED SPONGE 2 Cleaved under FX505GE LED SPONGE 2 - 21 V1.0...
Page 22
Disassembly Procedure *Notice: Add MB TOP ABSORBER. Alignment 13NR01A0L04011 FX505DY MB TOP ABSORBER/ Don’t cover this part. Notice: Add MB TOP SSD ABSORBER. 13NR01A0L09011 FX505DY MB TOP Alignment SSD ABSORBER 2 - 22 V1.0...
Page 24
Disassembly Procedure Top case Module The illustration below shows how to remove the Top case module. 1. Remove speaker. 2. Remove 4 screws on Hinge. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 3.0kgf-cm 13GMBKXD061Z-1: SCREW M2.5*6L (4.6,0.85) (K) B-ZN NY #1...
Disassembly Procedure LCD Module The illustration below shows how to remove the LCD module. 1. Remove the mylar on the both corners of bezel. 2. Remove 2 screws underneath. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 3.0kgf-cm 13050-B2504100: SCREW M2.5 *4.5L (4.5,0.5) (K) W-NI NY #1 2 - 27...
Page 28
Disassembly Procedure 3. Separate the bezel and LCD with Plastic Blade *Hooks inward (red frame position); hooks outward (blue frame position). 2 - 28 V1.0...
Page 29
Disassembly Procedure 4. Remove 6 screws and disconnect the EDP cable from LCD panel. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0kgf-cm; 3.0kgf-cm 13GMBK3C036Z-1: SCREW M2 *3L (4.6,0.8) (K) B-ZN NY #1 13050-B2803100*2 13050-B2803100: SCREW M2.5*...
Page 30
Disassembly Procedure * This Sponge will be shipped from the Hinge factory in the future. After the old material is consumed, it does not need to be posted in the factory. 5. Remove 2 LCD panel adhesives on the LCD cover. Notice: Slowly pull the adhesive up about 30 degrees.
Page 31
Notice: How to remove the LCD adhesive. Please refer to the below information. Notice: You can download the video from the link below to learn how to remove the adhesive. (Video name: GL504GS LCD Disassemble) http://sip.asus.com/document/DisplayDocument.aspx?folder_type=PUB&doc_id=210889 Notice :please slowly pull the adhesive up about 30 degree 30゜...
Page 32
Disassembly Procedure FX505GE LCD PANEL MYLAR UP// SUNYIEH 13NR00S0LC1011 FX505GE LCD PANEL MYLAR UP// TIANLIDA 13NR00S0LC1021 FX505DY LCD PANEL MYLAR Cleaved to the top of FX505DY LCD PANEL MYLAR 7. Remove camera with tweezers carefully. 8. Remove the EDP cable. 2 - 32 V1.0...
Page 33
Disassembly Procedure 9. Remove Antenna with tweezers carefully. Notice: If you need to replace hinges (hinge covers), please make sure hinge (hinge cover) R and hinge (hinge cover) L are the same vendor Notice: How to remove the LCD adhesive. Please refer to the below information. BACK 2 - 33 V1.0...
Page 34
Disassembly Procedure Gap Step 2 - 34 V1.0...