Table of Contents
Advertisement
Available languages
Available languages
5 of 6 - English
Auto retract
The auto retract feature can be toggled on or off depending on
user preference or specific job requirement. To turn auto
retraction off, remove rubber grommet and use a flat blade
screwdriver to rotate the indicator 90 degrees to either position
as shown below:
Troubleshooting guide:
Before you begin
1. Make sure that the battery is charged. Recheck the battery
after several minutes to make sure the battery is holding its
charge.
2. Use a nonflammable contact cleaner or pencil eraser to clean
the electrical contacts on the battery and tool.
3. Reinstall the battery and check the tool again.
Problem
Motor runs but
Insufficient hydraulic oil Contact Tool Service Center
the tool jaws will
not advance
Air block in hydraulic
Defective hydraulic circuit Contact Tool Service Center
Motor runs, tool
Insufficient hydraulic oil Contact Tool Service Center
jaws advance, but
will not build
Defective suction valve or
pressure
bypass cartridge
Motor will not run
Defective battery
at all
Bad contact or loose
battery connections
Misaligned switch
Tool jaws will not
Tool did not complete a full
release
cycle and bypass
Connector is jammed in
Release trigger is bent or
For parts or service, contact Tool Service Center at 1-800-284-TOOL (8665)
ON
OFF
Cause
for repair service
Invert tool to allow air to
system
rise towards the top of the
oil bladder
for repair service
for repair service
Contact Tool Service Center
for repair service
Charge or replace battery
Check all connections and
Check to make sure that
switch is properly aligned
with trigger
Contact Tool Service Center
for repair service
Press trigger and allow tool
to bypass,
then release tool jaws
Press and hold release
tool jaws
trigger while prying tool
jaws apart
Contact Tool Service
misaligned
Center for repair service
Parts list: TBM62PCR-LI
No.
901
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Solution
25
26
P-5 Back-Up Ring (E.L.)
27
28
29
30
31
32
33
35
36
37
38
39
wires
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
P-2 Back-Up Ring (B.C.)
Description
Housing L&R
MKHS-6REC
Cover
Switch Knob
Ratchet
Pin (280)
Spring (599)
Spring (720)
JE-3 Snap Ring
Terminal
Release Knob
Support Plate
Spring (719)
3 x 22 Parallel Pin
Indication Plate
M4x35 Parallel pin
On/Off switch pin
3 x 10 Drive Pin (AW)
Hanging Strap
M4 x 10 Screw
Switch Unit (24)S
MKREC-PCB
Power Unit
Pump Piston
Spring (699)
Cylinder Insert
P-5 O-ring (U565)
M5 X 5 Screw (F.P.)
Bush
5/32" Ball
Plug
G35 O-Ring
Plug
Oil Reservoir (43)
P-3 O-Ring (U801)
SI-9 Ring
Filter
Suction Plug
Spring (688)
Spring (718)
7/32" Ball
Valve Screw
Spring (686)
Valve Cartridge
Earth wire
KK Stem
Stem (1)
Lever Retainer
P-5 O-Ring (B)
S-7 O-Ring
Screw
9/64" Ball
Pressure sensor
Set screw
Cam Lever
Release Lever
Spring (689)
G4x12 Dowel Pin
Spring (77)
Spring (68)
Code
Qty
1
758-02
1
758-05
1
751-06
1
751-08
1
R150-09
1
751-09
1
51-39
2
7ND-04
1
751-10
1
751-11
1
751-12
1
ROB-121A
1
7ND-03
1
7ND-05
1
751-13
1
32-12
1
558-07A
3
ROB-159
9
1
751-15
1
751-16
4
LI200-04
4
LI200-05
4
LI200-06
4
LI200-07
4
510A-05
2
R14A-19
1
22-21
8
751-17
4
658-11
2
SLND-12
1
658-01
1
EZ-21
8
751-19
4
751-20
4
751-21
4
EZ-22
4
751-22
1
16-26
1
EZ-27
6
EZ-26
4
751-23B
1
758-06
1
751-24
1
751-25
2
751-26
1
610F-18
2
150A-05
1
751-27
1
751-30
2
758-07
1
758-08
1
751-28
1
758-04
1
EZ-23
1
658-10
2
16-37
1
26-21
2
RCP-37
1
Advertisement
Table of Contents
