Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Samsung 400MPX
Summary of Contents for Samsung 400MPX
-
Page 1: Lcd Monitor
LCD MONITOR quick start guide 400MP 460MP 400MPX 460MPX... -
Page 2: Package Contents
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type. Unpacking Manuals Quick Setup Guide... - Page 3 Others Remote Control (Not available in all loca- BNC to RCA Adaptor Jack Sold separately DVI Cable TV tuner box (Applicable to the MP model BNC Cable Note • You can purchase and connect a separate network box or TV tuner box. For information on how to use these, refer to their respective user manuals.
- Page 4 Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu val- ues.
- Page 5 Use this button for turning the LCD Display on and off. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods.
- Page 6 RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input)) DVI / PC / HDMI IN [HDMI] Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your dig- ital output device using a HDMI cable.
- Page 7 BNC/COMPONENT OUT[R/PR, G/Y, B/PB, H, V] (BNC/Component Connection Terminal (Out- put)) BNC (Analog PC) Connection: connecting the R, G, B, H, V ports. Component Connection: connecting the PR, Y, PB ports. BNC/COMPONENT IN[R/PR, G/Y, B/PB, H, (BNC/Component Connection Terminal (Input)) RGB OUT (Applicable to the MPn model only) LAN (LAN Connection Terminal)
-
Page 8: Remote Control
Note See Connecting Cables for further information regarding cable connections. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. Kensington Lock The Kensington Lock is a device used to physi- cally fix the system when using it in a public... - Page 9 POWER 3. Number Buttons POWER Number Buttons button + VOL - MUTE TV/DTV MENU INFO COLOR BUTTONS TTX/MIX STILL AUTO S.MODE LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT MagicInfo P.MODE DUAL/MTS SWAP Turns the product On. Turns the product Off.
- Page 10 4. DEL button 5. + VOL - MUTE 7. TV/DTV MENU INFO 11.COLOR BUTTONS TTX/MIX 13.STILL 14.AUTO 15. S.MODE 16.MDC 17.LOCK SOURCE ENTER/PRE-CH 20. CH/P 21.D.MENU 22.GUIDE RETURN The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV.
- Page 11 24. Up-Down Left-Right but- tons EXIT 27.MagicInfo 28. P.MODE DUAL/MTS 30. PIP 31.SWAP Mechanical Layout(400MP(N)) Mechanical Layout Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Exits from the menu screen. Selects SRS TruSurround XT mode. MagicInfo Quick Launch Button.
- Page 12 Introduction...
-
Page 13: Lcd Display Head
Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion. -
Page 14: Wall Bracket Installation
• Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. - Page 15 When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. Captive Screw Wall Bracket Hinge (Left) Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.
-
Page 16: To Mount The Product On The Wall Bracket
To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) Remove the 4 screws on the back of the product. Insert the screw B into the plastic hanger. -
Page 17: Wall Bracket Angle Adjustment
Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. Wall Bracket Angle Adjustment Adjust the bracket angle to -2°... - Page 18 Introduction Make sure to use the top center, and not the leftor the right side of the product to adjust the angle. Mechanical Layout(460MP(N)) Mechanical Layout...
- Page 19 Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display. • SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion.
- Page 20 • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
- Page 21 When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. Captive Screw Wall Bracket Hinge (Left) Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.
- Page 22 To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) Remove the 4 screws on the back of the product. Insert the screw B into the plastic hanger.
- Page 23 Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. Wall Bracket Angle Adjustment Adjust the bracket angle to -2°...
- Page 24 Introduction Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
-
Page 25: Connecting A Computer
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCR's or camcorders as well as your computer can be con- nected to the LCD Display. -
Page 26: Connecting To Other Devices
Turn on both your computer and the LCD Display. • The DVI cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. -
Page 27: Connecting To A Camcorder
Select AV using the SOURCE . Note The LCD Display has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the LCD Display is turned on. Connecting to a Camcorder Locate the A/V output jacks on the camcorder. -
Page 28: Connecting A Dtv Set Top Box
Connect a Component cable between the BNC/COMPONENT IN - P Display and the P Note • Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control. •... -
Page 29: Connecting Using A Dvi To Hdmi Cable
Connecting Using a HDMI Cable Note • Input devices such as digital DVD are connected to the HDMI terminal of the LCD Display using the HDMI cable. • You cannot connect a PC to the HDMI terminal. Connecting Using a DVI to HDMI Cable Note •... -
Page 30: Connecting A Usb Device
Connecting a LAN Cable Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un- wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCR's or camcorders as well as your computer can be con- nected to the LCD Display. - Page 31 Connections Note You can connect USB devices such as a mouse or keyboard. (Applicable to the MPn model only)
-
Page 32: Troubleshooting
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display. -
Page 33: Symptoms And Recommended Actions
• Do not use benzene, thinner or other flammable substan- ces, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen sur- face.) -
Page 34: Problems Related To The Screen
Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. The screen is blank and the power indicator is off. Ensure that the power cord is firmly connected and the LCD Display is on. -
Page 35: Problems Related To Audio
Adjust color using Custom under OSD Color Adjustment menu. The color image is distorted by dark shadows. Adjust color using Custom under OSD Color Adjustment menu. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The Power Indicator blinks. -
Page 36: Problems Related To Magicinfo
Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Problems related to MagicInfo Note Making a Bootable USB Flash Disk. Making a Bootable USB Flash Disk 1) You can turn a common 512-MB or bigger USB storage media into a bootable disk using a USB bootable disk creation tool. - Page 37 Set the resolution at the Control Panel → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Man- ual). How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the LCD Display with a soft cloth, using either a cleaning solution or plain water.