GE Hydran 201 i Instruction Manual page 14

Instruction Manual
5.2 Installation Overview. . . . . . . . . . . . . . . . . . . . . . . . 5-7
5.2.1 Tools and Material Required . . . . . . . . . . . . . . . . . 5-9
5.2.2 Mounting Location of the Hydran 201Ti . . . . . . . . . . . . . 5-9
5.2.2.1
5.2.2.2
5.2.3 Mounting Location of Hydran 201Ci Controllers . . . . . . . . . 5-12
5.2.4 Cabling and Network Configuration. . . . . . . . . . . . . . . 5-13
5.2.4.1
5.2.4.2
5.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6
Hydran 201Ti Installation
6.1 Incoming Inspection and Verification . . . . . . . . . . . . . . . . . 6-1
6.1.1 Receiving and Unpacking. . . . . . . . . . . . . . . . . . . 6-1
6.1.2 Shipping List. . . . . . . . . . . . . . . . . . . . . . . . 6-2
6.1.3 Inspecting . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
6.1.4 Storage and Battery Care . . . . . . . . . . . . . . . . . . . 6-5
6.2 Verification of Operation Prior to Installation . . . . . . . . . . . . . . 6-6
6.2.1 Preparation . . . . . . . . . . . . . . . . . . . . . . . . 6-6
6.2.2 Initial Observations . . . . . . . . . . . . . . . . . . . . . 6-7
6.2.3 Adjusting the Date and Time . . . . . . . . . . . . . . . . . 6-8
6.2.4 Verifying the Alarm Relays . . . . . . . . . . . . . . . . . . 6-9
6.2.4.1
6.2.4.2
6.2.4.3
6.2.4.4
6.2.4.5
6.2.4.6
6.2.5 Verifying the Backup Battery . . . . . . . . . . . . . . . . . 6-12
6.2.6 Sensor Serial Number Verification and Sensor Test . . . . . . . . 6-12
6.2.7 Adjusting the Temperature Set Point . . . . . . . . . . . . . . 6-13
6.2.8 Verifying the Analog Output (Facultative) . . . . . . . . . . . . 6-14
6.2.9 Verifying the RS-232 Communication (Facultative) . . . . . . . . 6-15
6.2.10 Completing the Verification . . . . . . . . . . . . . . . . . . 6-17
6.3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.1 Verifying the ac Power Supply Voltage and the Serial Numbers. . . . 6-18
6.3.2 Preparing the Hydran 201Ti . . . . . . . . . . . . . . . . . . 6-19
6.3.2.1
6.3.2.2
xiv
Warnings . . . . . . . . . . . . . . . . . . . . . 5-9
Typical Locations . . . . . . . . . . . . . . . . . . 5-10
Parameter Settings. . . . . . . . . . . . . . . . . . 5-13
Cabling . . . . . . . . . . . . . . . . . . . . . . 5-14
Gas High Alarm . . . . . . . . . . . . . . . . . . 6-9
Gas High-High Alarm . . . . . . . . . . . . . . . . 6-10
Fail Alarm . . . . . . . . . . . . . . . . . . . . . 6-10
Cancelling the Fail Alarm . . . . . . . . . . . . . . . 6-11
Cancelling the Gas Alarms . . . . . . . . . . . . . . 6-11
Conclusion . . . . . . . . . . . . . . . . . . . . 6-12
Removing the CPU Module . . . . . . . . . . . . . . 6-19
Separating the Brass Adaptor From the Heating Plate . . . . 6-20
Rev. 6, March 2011
5-15
6-17
Part 17997